• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 춘계학술대회 논문집
• /
• pp.18-22
• /
• 1992

This paper presents the process of manufacturing technology of ceramics ferrule for optical fiber connector. Precision zirconia ceramic ferrules is widely used for high performance and low cost single mode optical fiber connectors. To polish the hole of the zirconia ceramic ferrule, the wire lapping instrument is developed and the machining experiment is conducted. Through the centerless grinding using diamond wheel the surface roughness of zirconia ceramics ferrule is below the 1 .mu. m Rmax.

• 한국도로학회논문집
• /
• 제13권2호
• /
• pp.115-123
• /
• 2011

본 연구는 도심지 버스전용차로의 교차로 구간 아스팔트 포장을 프리캐스트 패널을 이용하여 강성 포장으로 교체하는 조립식 포장 시공을 수행한 후 이러한 포장의 초기 거동 및 공용성을 분석하기 위해 수행되었다. 조사 항목으로는 차량 진출입 구간에서 아스팔트 포장과 프리캐스트 패널과의 단차, 프리캐스트 패널간의 단차 및 줄눈 간격, 프리캐스트 패널의 침하, 패널 표면의 미끄럼저항 성능등을 선정하였다. 시공 후 일정시간이 지난 후에 다이아몬드 그라인딩 공법을 적용하여 이의 효과도 분석하였다. 추적조사 결과 시간이 경과함에 따라 프리캐스트 패널의 단차, 줄눈 간격, 침하, 미끄럼저항 등은 거의 변화가 없었으며, 이로 인해 프리캐스트 패널이 안정되게 하중을 지지하고 있다는 것을 알 수 있었다. 또한 다이아몬드 그라인딩 공법의 적용은 프리캐스트 패널의 단차 감소를 가져오는 것으로 확인되었다.

• 한국도로학회논문집
• /
• 제13권1호
• /
• pp.229-237
• /
• 2011

본 연구는 조립식 콘크리트 포장 공법을 이용하여 도심지 버스전용차로의 정거장 구간 아스팔트 포장을 강성 포장으로 교체하는 시공을 수행한 후 이러한 포장의 초기 공용성을 분석하기 위해 수행되었다. 추적조사 항목으로는 조립식포장의 진출입 구간에서 아스팔트 포장과 조립식포장과의 단차, 프리캐스트 슬래브간의 줄눈 간격 및 단차, 슬래브의 침하, 슬래브의 미끄럼저항 성능 등을 선정하였으며, 다이아몬드 그라인딩 공법의 적용성도 분석하였다. 추적조사 결과 조립식포장의 단차, 줄눈 간격, 미끄럼저항, 침하 등은 시간에 따라 변화가 거의 없었으며, 이를 통해 프리캐스트 슬래브가 차량하중을 안정되게 지지한다는 것을 알 수 있었다. 또한 다이아몬드 그라인딩 공법을 적용하면 슬래브의 단차 및 미끄럼저항 성능을 크게 개선할 수 있는 것도 확인할 수 있었다.

• 한국정밀공학회지
• /
• 제30권3호
• /
• pp.324-330
• /
• 2013

This paper describes a novel method to surface large optics mirror with an extremely high hardness, which could replace the high cost of the repetitive off-line measurement steps and the large ultra-precision grinding machine with ultra-positioning control of 10 nm resolution. A lot of diamond pellet to be attached on the convex aluminum base consists of a grinding tool for the concave large mirror, and the tool was pressured down on the large mirror blank. The tool motion at an interval on the spiral path was controlled with each feed rate as the dwell time in the conventional computer-controlled polishing. The shape to be surfaced was measured directly by a touch probe on the machine without any separation of the mirror blank. Total 40 iterative steps of the surfacing and measurement could demonstrate the form error of RMS $7.8{\mu}m$, surface roughness of Ra $0.2{\mu}m$ for the mirror blank with diameter of 1 m and spherical radius of curvature of 5400 mm.

• The Journal of Advanced Prosthodontics
• /
• 제6권6호
• /
• pp.434-443
• /
• 2014

PURPOSE. The purpose of this study was to evaluate and compare the effects of different surface pretreatment techniques on the surface roughness and shear bond strength of a new self-adhering flowable composite resin for use with lithium disilicate-reinforced CAD/CAM ceramic material. MATERIALS AND METHODS. A total of one hundred thirty lithium disilicate CAD/CAM ceramic plates with dimensions of $6mm{\times}4mm$ and 3 mm thick were prepared. Specimens were then assigned into five groups (n=26) as follows: untreated control, coating with $30{\mu}m$ silica oxide particles ($Cojet^{TM}$ Sand), 9.6% hydrofluoric acid etching, Er:YAG laser irradiation, and grinding with a high-speed fine diamond bur. A self-adhering flowable composite resin (Vertise Flow) was applied onto the pre-treated ceramic plates using the Ultradent shear bond Teflon mold system. Surface roughness was measured by atomic force microscopy. Shear bond strength test were performed using a universal testing machine at a crosshead speed of 1 mm/min. Surface roughness data were analyzed by one-way ANOVA and the Tukey HSD tests. Shear bond strength test values were analyzed by Kruskal-Wallis and Mann-Whitney U tests at ${\alpha}=.05$. RESULTS. Hydrofluoric acid etching and grinding with high-speed fine diamond bur produced significantly higher surface roughness than the other pretreatment groups (P<.05). Hydrofluoric acid etching and silica coating yielded the highest shear bond strength values (P<.001). CONCLUSION. Self-adhering flowable composite resin used as repair composite resin exhibited very low bond strength irrespective of the surface pretreatments used.

• 대한치과기공학회지
• /
• 제38권3호
• /
• pp.157-163
• /
• 2016

Purpose: It is to compare and evaluate the change of the wear rate and phase variation of the Zirconia before and after the sintering after the grinding by a high speed equipment manufactured for the Zirconia. Methods: The specimen of the sintered Zirconia was manufactured as size of $15mm{\times}15mm{\times}2mm$. The grinding has been applied to each of all pieces of each test groups for a minute fit for each condition at same speed of 50,000 rpm by a diamond bur at high speed handpiece with injection of the air and water. For the observation of the surface before and after the sintering of the each test piece, the cross section of it was observed as 100 magnification by a scanning electron microscope after it was coated by PT, and the diffraction analysis was performed by XDR to compare the crystal phase of the Zirconia. The average surface roughness value of all specimens were evaluated. The wear test was performed at room temperature by applying a load of 1kg for 120,000 cycles for the chewing period 6 months. Wear was analyzed for the enamel cusps by measurement of the vertical substance loss with a laser scanner. Conclusion: The phase variation from the tetragonal phase to the monoclinic phase was confirmed in the test group of the pre-sintered Zirconia after the grinding, and the value of the surface roughness and the wear rate was increased in experimental group.

• 한국화재소방학회논문지
• /
• 제32권6호
• /
• pp.108-116
• /
• 2018

구리 용융흔(Melted bead) 미세조직(Microstructure)은 변형층(Deformed layer)과 원조직(Undeformed layer)으로 구분할 수 있다. 변형층이 존재하는 경우에는 측정오류가 발생되어 연마/미세연마(Grinding/Polishing)를 통하여 변형층을 제거하고 원조직을 관측하여야 한다. 이에 따라 본 연구에서는 구리 용융흔의 미세조직 분석을 위한 연마/미세연마 절차(Process)를 제시하였다. 변형층 제거를 위해 연마재 종류/크기, 연마시간, 연마율의 상관성을 분석하였고 변형층의 두께를 $1{\mu}m$ 이하가 되도록 하였다. 연구결과, 실리콘카바이드 연마재 $15{\mu}m$ (SiC P1200) 2 min, $10{\mu}m$ (SiC P2400) 1 min, 다이아몬드 연마재 $6{\mu}m$ 8 min, $3{\mu}m$ 6 min, $1{\mu}m$ 10 min, $.25{\mu}m$ 8 min 실시하는 새로운 연마/미세연마 절차를 제시하였다. 또한 최종 단계에서 3 min 동안 콜로이달 실리카 $.04{\mu}m$로 화학적 미세연마를 실시함으로써 미세조직의 선명성을 증대시키는 방안도 제시하였다. 연마/미세연마 시간은 총 38 min이 소요되며, 기존에 제시된 시간, 절차보다 단순화 하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.178-178
• /
• 2009

High-density optical information storing equipment, which is using Blu-ray, is the next generation information storing equipment that has about form six times to thirty-five times capacities. and high-density optical information storing equipment uses high NA(Numerical Aperture) aspheric glass objective lens as optical pick-up equipment to record and recognize high-density date. Generally this objective lens is developed and produced through a way of GMP(Glass Molding Press) that uses molding core that is performde by Ultra precision grinding, but grinding performing that has high-accuracy is very difficult because objective lens form is high NA. In this research, we preformed Ultra precision turning, using single crystal diamond bite, about WC(Co 0.5%), sintering brittleness material that is used molding core's material for GMP. and we confirmed aspheric glass lens compression of deformities molding core's Ultra precision turning possibility by measuring surface roughness(Ra) and processing surface's condition.

• The Journal of Advanced Prosthodontics
• /
• 제10권2호
• /
• pp.132-137
• /
• 2018

PURPOSE. The purpose of this study was to evaluate and compare three polishing systems on the surface roughness and phase transformation of monolithic zirconia. MATERIALS AND METHODS. 100 disk shaped specimens (10 mm diameter, 3 mm thickness) were fabricated from monolithic zirconia blocks. 20 specimens were left as a control group and remaining specimens were grinded by diamond bur to simulate the occlusal adjustments. Grinded specimens were randomly divided into 4 groups: group G (no polishing), group M (Meisinger, zirconia polishing kit), group E (EVE Diacera, zirconia polishing kit), and group P (EVE Diapol, porcelain polishing kit). Surface roughness was measured with profilometer and surface topography was observed with SEM. XRD analysis was performed to investigate the phase transformation. Statistical analysis was performed with one-way ANOVA and Tukey's post hoc tests at a significance level of P=.05. RESULTS. All polishing groups showed a smoother surface than group G. Among 3 polishing systems, group M and group E exhibited a smoother surface than the group P. However, no significant differences were observed between group M and group E (P>.05). Grinding and polishing did not cause phase transformations in zirconia specimens. CONCLUSION. Zirconia polishing systems created a smoother surface on zirconia than the porcelain polishing system. Phase transformation did not occur during the polishing procedure.

• 한국기계가공학회지
• /
• 제17권1호
• /
• pp.63-68
• /
• 2018

At present, ultra-precision cutting technology has been studied in Korean research institutes, focusing on development of ultra-precision cutting tool technology and ultra-precision control engineering. However, the developed technologies are still far behind advanced countries. It focuses on metals including aluminum, copper and nickel, and nonmetals including plastics, silicone and germanium which require high precision while using a lathe. It is hard to implement high precision by grinding the aforementioned materials. To address the issue, the ultra-precision cutting technology has been developing by using ultra-precision machine tools very accurate and strong, and diamond tools highly abrasion-resistant. To address this issue, this study aims to conduct ultra-precision cutting by using ECTS (Error Compensation Tool Servo) to improve motion precision of elements and components, and compensate for motion errors in real time. An IR camera is used for analyzing cutting accuracy differences depending on the heat generated in diamond tools in cutting to examine the heat generated in cutting to study cutting accuracy depending on generated heat.