• 한국항해항만학회지
• /
• 제29권7호
• /
• pp.627-634
• /
• 2005

Gunsan-Janghang Harbor is located at the mouth of Gum River, on the central west coast of Korea The harbor and coastal boundaries are protected from the effects of the open ocean by natural coastal islands and shoals due to depositions from the river, and two breakwaters. The navigation channel commences at the gap formed by the outer breakwater and extends through a bay via a long channel formed by an isolated jetty. For better understanding and analysis of wave transformation process where a wide coastline changes appear due to on-going reclamation works, we applied the spectral wave model including wind effect to the related site, together with the energy balance models. This paper summarizes comparisons of coastal responses predicted by several numerical wave predictions obtained at the coastal waters near Gunsan-Janghang Harbor. Field and numerical model investigations were initially conducted for the original navigation channel management project. We hope to contribute from this study that coastal engineers are able to use safety the numerical models in the area of port and navigational channel design.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.303-308
• /
• 2004

The failure at the head section of rubble mound breakwaters is more important than other failure modes. because this initial failures will occur the failure of the trunk section and lead to the instability of the structure. The three-dimensional failure modes are discussed using the experimental data with multi-directional waves considering the failure modes. It was occurred by the topographical characteristics around the head of rubble mound breakwater. The spacial characteristics of failure mode around the rubble-mound structures can be summarized as follows: 1) It was clarified that the failure modes at the round head of a detached breakwater are classified as failure by plunging breaker on the slope, failure by direct incident wave force and failure at the rubble mound breakwaters. 2) The failure mode was found in the lower wave height than the design wave by the breaker depth effects and topography around structures. It is clarified that the structure was monitored safely designed for the design wave but the failure was occurred by the reason of breaker waves.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.447-449
• /
• 2004

The purpose of this study is measured surface acoustic wave(SAW) characteristics to confirm utilization possibility as SAW sensor using new Pb(Mg$_{1}$3/Nb$_{2}$3/) $O_3$-PbTiO$_3$ (PMN-PT) piezoelectric substrate. We have tried to see if the material can be practically available as a new surface acoustic wave (SAW) biosensor to detect protein. The experimental results clarified that the frequency filtering of the central frequency of the PMN-PT substrate is a superior result to that of the LiTaO$_3$ (LT) substrate, but the result was not completely satisfactory. We know there is a problem in the design of inter-digital transducer (IDT) pattern. The waves transferred through the input terminal forms SAW which is sure to be transferred to the direction of the output terminal and the backward direction of the input terminal. This reflected wave is reiterated with SAW, which is transferred to the output direction, and so the frequency filtering gives a not good result. The electromechanical coupling coefficient of the PMN-PT substrate is excellent, and we can use it as a SAW sensor, in the near future, provided that there will be a new IDT design to increase the frequency filtering.

• Journal of electromagnetic engineering and science
• /
• 제1권1호
• /
• pp.95-99
• /
• 2001

According to the progress of the electronic industy and radio communication technologies, mankind might enjoy its abundant life On the other hand, many social problems such as EMI, and unnecessary electromagnetic wave occur due to the increased use of electromagnetic wave. Therefore, the organiztions such as CISPR, FCC, ANSl,etc. have provided the standard of electromagnetic wave enviroment for the countermeasure of the EMC. It had been required that the absorbing ability of an electromagnetic wave absorber is more than 20 dB, the bandwidth of which is required through 30 MHz to 1,000 MHz for satisfying the international standard about an anechoic chamber for EMI/EMS measurment. From November of 1998, however, the CISPRll has accepted the extended frequency band from 1 GHz to 18 GHz additionally in the bandwidth of EMI measurementent$^{[1]}$ . In this paper, we proposed a new type absorber satisfying the above requirements and carried out broadband design using the equivalent material constants method. Futheremore, the experiments were carried out over the frequency band from 30 MHz to 2 GHz, and hence, the validity of the proposed design theory was confirmed.

• 한국의류산업학회지
• /
• 제11권1호
• /
• pp.156-165
• /
• 2009

The purpose of this study was to compare men's hair style preference by gender according to occassion. Data were collected through a survey of 149 males and 175 females and analyzed by SPSS packages. The results of this study were as follows : 1) Male prefers to short, straight and black hair while female prefers to shot, nature wave and black hair. 2) Both male and female don't prefer to permanent and hair dyeing. 3) On the occasion of job interview, both male and female prefer to short, straight and black hair. On the occasion of blind date, male prefers to short, straight and black hair while female prefers to short, natural wave and natural brown hair. On the occasion of matchmaker meeting for marriage, male prefers to short, straight and black hair while female prefers to short, natural wave and dark brown hair. On the occasion of club party, male prefers to middle length, straight and black hair while female prefers middle length, natural wave and natural brown hair. On the occasion of leasure time, male prefers to short, straight and black hair while female prefers to short, natural wave and natural brown hair. And both male and female prefer to use hats for skin protection during outdoor leasure time.

• 드라이브 ㆍ 컨트롤
• /
• 제11권3호
• /
• pp.31-40
• /
• 2014

This paper proposes a multi absorbing wave energy converter design, in which a hydrostatic transmission is used to transfer wave energy to electric energy. The most important feature of this system is its combination of the pressure coupling principle with the use of a hydraulic accumulator to eliminate the effects of wave power fluctuation; this maintains a constant speed of the hydraulic motor. Tilt motion of a floating buoy was employed as the power take-off mechanism. Furthermore, a PID controller was designed to carry out the speed control of the hydraulic motor. The design offers some advantages such as extending the life of the hydraulic components, increasing the amount of energy harvested, and stabilizing the output speed.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제12권1호
• /
• pp.283-296
• /
• 2020

A numerical model is established to investigate the run-up of a solitary wave after propagating over a triangular saw-tooth-shaped submerged breakwater. A rectangular-shaped submerged breakwater is simulated for comparison. Several factors, including the submerged depth, the lagoon length and the beach slope, are selected as independent variables. The free surface motions and velocity fields of the solitary wave interacting with the submerged breakwater are discussed. The results show that the submerged depth and lagoon length play significant roles in reducing the run-up. The influence of the beach slope is not significant. At the same submerged depth, the triangular saw-tooth-shaped submerged breakwater has only a slightly better effect than the rectangular-shaped submerged breakwater on the run-up reduction. However, a calmer reflected wave profile could be obtained with the rougher surface of the saw-tooth-shaped submerged breakwater. The study conclusions are expected to be useful for the conceptual design of saw-tooth-shaped submerged breakwaters.

• Nuclear Engineering and Technology
• /
• 제54권9호
• /
• pp.3540-3550
• /
• 2022

The supercritical carbon dioxide (S-CO₂) Brayton cycle is an important energy conversion technology for the fourth generation of nuclear energy. Since the printed circuit heat exchanger (PCHE) used in the S-CO₂ Brayton cycle has narrow channels, Rayleigh-Bénard (RB) convection is likely to exist in the tiny channels. However, there are very few studies on RB convection in supercritical fluids. Current research on RB convection mainly focuses on conventional fluids such as water and air that meet the Boussinesq assumption. It is necessary to study non-Boussinesq fluids. PRB convection refers to RB convection that is affected by horizontal incoming flow. In this paper, the computational fluid dynamics simulation method is used to study the PRB convection phenomenon of non-Boussinesq fluid-supercritical carbon dioxide. The result shows that the inlet Reynolds number (Re) of the horizontal incoming flow significantly affects the PRB convection. When the inlet Re remains unchanged, with the increase of Rayleigh number (Ra), the steady-state convective pattern of the fluid layer is shown in order: horizontal flow, local traveling wave, traveling wave convection. If Ra remains unchanged, as the inlet Re increases, three convection patterns of traveling wave convection, local traveling wave, and horizontal flow will appear in sequence. To characterize the relationship between traveling wave convection and horizontal incoming flow, this paper proposes the relationship between critical Reynolds number and relative Rayleigh number (r).

• 한국지반공학회논문집
• /
• 제25권9호
• /
• pp.45-55
• /
• 2009

철도 토공노반의 품질은 현장 밀도나 평판재하시험을 통해 관리되어 왔다. 현재 지반반력계수($k_{30}$)의 경우 일반철도와 고속철도의 설계기준으로도 사용되기 때문에 설계와 품질관리에서 일관성을 갖는다. 그럼에도 불구하고 지반반력계수($k_{30}$), 또는 반복평판재하시험의 결과인 변형계수($E_{v2}$)와 변형계수의 비($E_{v2}/E_{v1}$) 같은 설계인자에 대해 간편한 실내기준 설정 방법이 없어 설계과정의 치명적인 결함으로 남는다. 본 예비연구에서는 이러한 단점을 극복하고자 최근 개발된 철도 토공노반의 역학적-경험적 설계 방법에도 합당한 새로운 품질관리 기준으로 압축파 속도를 도입하였고 계측 기법을 제안하였다. 품질관리 방안의 핵심은 다짐시험과 병행하여 획득한 최적함수비에서의 압축파 속도를 현장의 품질관리 기준으로 설정하고 현장에서는 시공 중에 직접도달파 기법으로 품질을 확인하는 것이다. 직접도달파 기법은 현장의 기술자가 지표면 얕은 깊이의 균질한 층에서 간편하게 적용할 수 있고 저림하며 결과의 신뢰성이 높다. 시험 부지에서 직접도달파 시험으로부터 계측한 압축파 속도가 다짐도에 따라 식별 가능한지 확인하였고, 품질관리 지표로서 압축파 속도를 효과적으로 적용할 수 있음을 입증하였다. 본 논문의 현장 및 실내 압축파 계측을 통해 동반논문(박철수 등, 2009)에서 수행할 실험적 토대를 마련하였다.

• 한국해양공학회지
• /
• 제28권3호
• /
• pp.227-235
• /
• 2014

Using a 3-D numerical scheme (LES-WASS-3D) that considered wave-structure-sandy seabed interactions in a 3-D wave field, we analyzed the wave reflection and hydraulic characteristics inside a slit caisson with two chambers in a 3-D oblique wave field. To verify the 3-D numerical analysis method suggested in this study, we compared the numerical results with existing experimental results and found good agreement. The numerical analysis revealed that a standing wave field is generated on the front side of the slit caisson due to the effect of wave reflection. For incident waves propagating perpendicular to the slit caisson, the nodes and anti-nodes of the standing wave are apparent and symmetrical. However, in an oblique wave field, as the incident wave angle decreases, the nodes and anti-nodes of the standing wave become ambiguous and unsymmetrical. It was also found that the wave reflection coefficient decreases as the incident wave angle decreases. It can be pointed out that as the incident wave angle decreases, the turbulent intensity in the chamber increases. Thereby, the increased wave energy dissipation by the increased turbulent intensity reduces the rate of wave reflection. In addition, a strong turbulent intensity generally occurs in the first chamber.