• 대한기계학회논문집 C: 기술과 교육
• /
• 제5권2호
• /
• pp.115-126
• /
• 2017

본 논문은 특수 차량용 동력 전달계 부품인 구동축의 가속 수명 시험을 수행하는 것이다. 동력 전달계 부품의 수명 평가를 위하여 사용환경의 주행 부하 스펙트럼의 데이터가 필요하나, 특수 차량의 경우 부하 스펙트럼을 구할 수 없는 경우가 대부분이다. 따라서, 본 논문에서는 차량 데이터와 특수 주행로 조건에 기반하여 주행 부하 로드 스펙트럼을 모델링하고 시뮬레이션 하였다. 가속 수명 시험에는 역승 모델을 적용하였고, 마이너 법칙을 사용하여 등가 토크를 구하였으며, 구동축 가속 수명 시험을 위하여 교정 가속법을 사용하였다. 피로시험은 세 수준의 스트레스로 수행하였으며, 사용자 스트레스 수준의 수명은 외삽법을 사용하여 예측 하였고, 실제 시험 결과와 부하 스펙트럼 데이터와의 비교로 수명을 검증하였다.

• Advances in Computational Design
• /
• 제7권4호
• /
• pp.371-393
• /
• 2022

This paper presents a three-dimensional flexible pavement simulated in ANSYS subjected to moving vehicular load on the surface of the pavement typical for the road section in Nepal. The adopted finite element (FE) model of pavement is validated with the classical theoretical formulations for half-space pavement. The validated model is further utilized to understand the damping and dynamic response of the pavement. Transient analysis of the developed FE model is done to understand the time varying response of the pavement under a moving vehicle. The material properties of pavement considered in the analysis is taken from typical road section used in Nepal. The response quantities of pavement with nonlinear viscoelastic asphalt layer are found significantly higher compared to the elastic pavement counterpart. The structural responses of the pavement decrease with increase in the vehicle speed due to less contact time between the tires of the vehicle and the road pavement.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.816-823
• /
• 2007

As the South Korean rolling stock industry is developing designs for full compliance with the European Standards, it is fitting to take a look at these two core standards. The paper presents an overview of the load cases and structural requirements developed in Europe for the design of safe and compatible rolling stock vehicles. These load cases and structural requirements have been compiled into two standards namely EN12663 and EN15227. Standard EN12663 was developed as a reference design requirements standard. The work was mandated and sponsored by the European Committee for Standardization and Standard issuing National Institutions. EN12663 specifies a series of proof and fatigue load cases for European rolling stock regulations compliant vehicle designs. As EN12663 does not address the crashworthiness issue, a dedicated crashworthiness standard, EN15227, was therefore developed in a similar manner through industry wide consultations managed by a Trans-European working group of experienced engineers and specialists. In both standards, the vehicle and/or trains are grouped into categories reflecting the vehicle types and/or their indented operational function. EN15227, developed to complement EN12663, addresses the "passive" crashworthiness capability of the vehicles and trains. EN15227 specifies reference crash scenarios similar to those found in the Technical Specification for Interoperability (TSI) of high speed trains operating in Europe. The overview also touches on a general comparison with the corresponding British Group Standard (GM/RT2100) and also the UIC leaflet based load cases. The exercise is extended to pertinent design load cases specified by the Federal Railroad Administration (FRA) in the US.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.179-184
• /
• 2005

In the present study, conceptual design of the main wing for 20 seats WIG{wing in Ground Effect) flight vehicle, which will be a high speed maritime transportation system for the next generation, was performed. The high stiffness and strength Carbon-Epoxy material was used for the major structure and the skin-spar with a foam sandwich structural type was adopted for improvement of lightness and structural stability. As a design procedure for this study, firstly the design load was estimated with maximum flight load, and then flanges of the front and the rear spar from major bending load and the skin structure and the webs of the spars were preliminarily sized using the netting rules and the rule of mixture. In order to investigate the structural safety and stability, stress analysis was performed by Finite Element Codes such as NASTRAN/PA TRAN[6] and NISA II [7]. From the stress analysis results, it was confirmed that the upper skin structure between the front spar and rear spar was very unstable for the buckling. Therefore in order to solve this problem, a middle spar and the foam sandwich structure at the upper skin and the web were added. After design modification, even thought the designed wing weight was a little bit heavier than the target wing weight, the structural safety and stability of the final design feature was confirmed. Moreover, in order to fix the wing structure at the fuselage, the insert bolt type structure with six high strength bolts was adopted for easy assembly and removal.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1553-1555
• /
• 2005

This paper presents a design of lossless hybrid-type magnetically-levitated vehicle. The lossless hybrid-type system is implemented by a permanent magnet and electromagnet. The target plant consists of eight hybrid-type magnets and in the steady-state, no current is needed to support the load. The design procedure is described and the results of this work are shown.

• 한국자동차공학회논문집
• /
• 제23권6호
• /
• pp.591-600
• /
• 2015

The efficiency of a powertrain system of hybrid vehicle is highly dependent on the design and control of the hybrid powertrain system. In other words, the optimal design of the powertrain systems is coupled with optimal control of the powertrain system. Therefore, the solution of an optimal design problem for hybrid vehicles is computationally and timely very expensive. For example, dynamic programming, which is a recursive optimization method, is usually used to evaluate the best fuel economy of certain hybrid vehicle design, and, thus, the evaluation takes tens of minutes to several hours. This research aims to accelerate the speed of efficiency evaluation of hybrid vehicles. We suggest a mathematical treat and a methodological treat to reduce the computational load. The mathematical treat is that the dynamics of system is discretized with sparse sampling time without loss of energy balance. The methodological treat is that the efficiency of the hybrid vehicle is inferred by characteristic loss evaluation that is computationally inexpensive. With the suggested methodology, evaluating a design candidate of hybrid powertrain system is taken few minutes, which was taken several hours when dynamic programming is used.

• 농업과학연구
• /
• 제51권2호
• /
• pp.133-146
• /
• 2024

Selection of gear reduction ratio is essential for machine design to ensure suitable power and speed during agricultural operations. The goal of the study was to evaluate the gear reduction ratio for a 1.6 kW four-wheel-drive (4WD) multi-purpose agricultural electric vehicle platform using workload data under different off-road conditions. A data acquisition system was fabricated to collect workload (torque) of the vehicle acting on the gear shaft. Field tests were performed under three driving surfaces (asphalt, concrete, and grassland), payload operations (981, 2,942, and 4,903 N), and slope conditions (0 - 4°, 4 - 8°, and 8 - 12°), respectively. Commercial speed reduction gear phases were attached to the input shaft of the vehicle powertrain. The maximum required torque was recorded as 37.5 Nm at a 4,903 N load with 8 - 12° slope levels, and the minimum torque was 12.32 Nm at 0 - 4° slope levels with a 981 Nm load for a 4 km/h speed on asphalt, concrete, and grassland roads. Based on the operating load condition and motor torque and rotational speed (TN) curve, the minimum and maximum gear reduction ratios were chosen as 1 : 50 and 1 : 64, respectively. The selected motor satisfied power requirements by meeting all working torque criteria with the gear reduction ratios. The chosen motor with a gear reduction ratio of 1 : 50 was suitable to fit with the motor T-N curve, and produced the maximum speeds and loads needed for driving and off-road activities. The findings of the study would assist in choosing a suitable gear reduction ratio for electric vehicle multi-purpose field operations.

• 한국전산구조공학회논문집
• /
• 제27권6호
• /
• pp.533-542
• /
• 2014

본 연구에서는 차량과 교각의 직접충돌해석을 통하여 기존 설계기준(도로교설계기준, AASHOTO LRFD)에서 아직 고려하고 있지 않은 동적영향을 고려한 실제 교각의 충돌 파괴 거동을 다양한 경계조건별로 검토하였다. 선정된 차량은 10톤, 16톤, 38톤의 Cargo 트럭이며 교각은 경부고속도로 상 일반적인 제원으로 선정하였다. 해석결과 가장 많은 파괴는 상부구조의 고려없이 교각의 상부면을 구속하였을 시에 발생하였으며 상부구조는 2차적인 영향을 교각에 전달하기 보다는 충돌에너지를 일부 흡수하는 역할을 하며 파괴를 감소시키는 것으로 확인되었다. 또한 해석의 효율성을 위해 차량과 강체간 충돌시 발생하는 충돌하중이력곡선을 교각에 외력으로 부여한 간접충돌해석을 수행하고, 이를 직접충돌해석 결과와 비교하였다. 해석 결과 직접충돌해석 결과와 매우 유사하게 교각의 거동을 예측하는 것으로 확인되었으며 해석효율성 또한 높아져 해석시간은 약 92%정도 감소하였다. 이러한 간접충돌해석법은 다양한 기존 모델이나 다른 해석프로그램에도 쉽게 부여될 수 있어 그 활용범위가 증가할 것으로 판단된다.

• Structural Engineering and Mechanics
• /
• 제60권2호
• /
• pp.237-249
• /
• 2016

There are constraints on truck weight, axle configurations and size imposed by departments of transportation around the globe due to structural capacity limitations of highway pavements and bridges. In spite of that, freight movers demand some vehicles that surpass the maximum size and legal weight limits to use the transportation network. Oversized trucks serve the purpose of spreading the load on the bridge; thus, reducing the load effect on the superstructure. For such vehicles, often a quick structural analysis of the existing bridges along the traveled route is needed to ensure that the structural capacity is not exceeded. For a wide vehicle having wheel gage larger than the standard 1830 mm, the girder distribution factors in the design specifications cannot be directly used to estimate the live load in the supporting girders. In this study, a simple approach that is based on finite element analysis is developed by modifying the AASHTO LRFD's girder distribution factors for slab-on-steel-girder bridges to overcome this problem. The proposed factors allow for determining the oversized vehicle bending moment and shear force effect in the individual girders as a function of the gage width characteristics. Findings of the study showed that the relationship between the girder distribution factor and gage width is more nonlinear in shear than in flexure. The proposed factors yield reasonable results compared with the finite element analysis with adequate level of conservatism.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1127-1132
• /
• 2003

Suspension system of vehicle have enough endurance during its life time to protect passenger. Spring is one of major part of vehicle. Thus, a fatigue strength evaluation for leaf spring based on road load response was carried out. At first, strain of leaf spring is measured on the city condition and proving ground condition. And next, the damage analysis of road load response data was carried out. And fatigue test of leaf spring were also carried out. Based on -N life relation, fatigue life of leaf spring was evaluated at belgian mode, city mode and drawing test specification. After that, it is compared the design life of leaf spring and evaluated fatigue life by belgian mode, city mode and drawing test specification. From the above, the maximum load-fatigue life relation of leaf spring was defined by test. and new test target of belgian mode and city mode was proposed to accept design specification of leaf spring. It is expect that proposed test target can verify leaf spring fatigue endurance at specific road condition.