• Journal of Aerospace System Engineering
• /
• v.16 no.2
• /
• pp.63-72
• /
• 2022

As interest in microsatellites increases, research has been actively conducted recently on the performance and use, as well as the orbital design and deployment techniques, for the microsatellite constellations. The purpose of this study was to investigate orbital deployment techniques using thrust and differential atmospheric drag control (DADC) for the Walker-delta constellation. When using thrust, the time and thrust required for orbital deployment vary, depending on the separation speed and direction of the satellite with respect to the launch vehicle. A control strategy to complete the orbital deployment with limited performance of the propulsion system is suggested and it was analyzed. As a result, the relationship between the deployment period and the total thrust consumption was derived. It takes a relatively longer deployment time using differential air drag rather than consuming thrusts. It was verified that the satellites can be deployed only with differential air drag at a general orbit of a microsatellite constellation. The conclusion of this study suggests that the deployment strategy in this paper can be used for the microsatellite constellation.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.6
• /
• pp.93-101
• /
• 2022

RC Slab bridges in Korea account for more than 70% of the total bridges for more than 20 years of service. As the number of aging structures increases, the importance of safety diagnosis and maintenance of structures increases. For highway bridges, cracks are a main cause of deck deterioration, which is very closely related to the decrease in bridge durability and service life. In addition, the damage rate of expansion joints and bearings accounts for approximately 73% higher than that of major members. Therefore, this study defined damage scenarios combined with devices damages and deck deterioration. The stress distribution and maximum stress on the deck were then evaluated using design vehicle load and daily temperature gradient for single and combined damage scenarios. Furthermore, this study performed damage-spread analysis and predicted condition ratings according to a deck deterioration model generated from the inspection and diagnosis history data of cracks. The heterogeneous damages combined with the member damages of expansion joints and bearings increased the rate of crack area and damage spread, which accelerated the time to reach the condition rating of C. Therefore, damage to bridge members requires proper and prompt repair and replacement, and otherwise it can cause the damage to bridge deck and the spread of the damage.

• Journal of The Korean Association of Information Education
• /
• v.25 no.6
• /
• pp.947-960
• /
• 2021

In this study, we examine the AI ethics perception of university students to explore the direction of AI ethics education. For this, 83 students wrote their thoughts about 5 discussion topics on online bulletin board. We analyzed it using language networks, one of the text mining techniques. As a result, 62.5% of students spoke the future of the AI society positively. Second, if there is a self-driving car accident, 39.2% of students thought it is the vehicle owner's responsibility at the current level of autonomous driving. Third, invasion of privacy, abuse of technology, and unbalanced information acquisition were cited as dysfunctions of the development of AI. It was mentioned that ethical education for both AI users and developers is required as a way to minimize malfunctions, and institutional preparations should be carried out in parallel. Fourth, only 19.2% of students showed a positive opinion about a society where face recognition technology is universal. Finally, there was a common opinion that when collecting data including personal information, only the part with the consent should be used. Regarding the use of AI without moral standards, they emphasized the ethical literacy of both users and developers. This study is meaningful in that it provides information necessary to design the contents of artificial intelligence ethics education in liberal arts education.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.6
• /
• pp.284-298
• /
• 2022

It is necessary to acquire information on traffic safety facilities installed on the roadways specifically for the operation of autonomous vehicles. The purpose of this study is to prepare a Korean version of an integrated message-set design as a way to provide to autonomous vehicles standardized information on traffic safety facilities. In this study, necessary facilities are classified according to four criteria (no legal basis; not providing information to autonomous vehicles; providing duplicate information; not standardized, and too difficult to generalize) based on information that must be provided to operate autonomous vehicles. The priority of information delivery (gross negligence followed by behavior change) was classified according to the importance of the information to be provided during autonomous driving, and the form was defined for the classification code in the information delivered. Finally, the information location and delivery method of traffic facilities for compliance with SAE J2735 were identified. This study is meaningful in that it provides a plan for roadway operations by suggesting a method for providing information to autonomously driven vehicles.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.4
• /
• pp.54-63
• /
• 2022

A 3-tonf class liquid rocket engine that powers the upper stage of a small launcher and lifts 500 kg payload to 500 km SSO is designed. The small launcher is to utilize the flight-proven technology of the 75-tonf class engine for the first stage. A combination of liquid oxygen and liquid methane has been selected as their cryogenic states can provide an extra boost in specific impulse as well as enable a weight saving via the common dome arrangement. An expander cycle is chosen among others as the low-pressure operation makes it robust and reliable while a specific impulse of over 360 seconds is achievable with the nozzle extension ratio of 120. Key components such as combustion chamber and turbopump are designed for additive manufacturing to a target cost. The engine system provides an evaporated methane for the autogenous pressurization system and the reaction control of the stage. This upper stage propulsion system can be extended to various missions including deep space exploration.

• Journal of the Institute of Convergence Signal Processing
• /
• v.23 no.4
• /
• pp.228-233
• /
• 2022

This study is an experimental study on how to use phase change materials(PCM) to generate electrical energy for long-term operation of underwater unmanned vehicles. The electrical energy generation method is a volume change and a pressure change that occur as a phase change material changes to a solid or liquid state according to temperature, and the change in pressure creates a flow of fluid to create electrical energy. Polyethylene glycol was used as a phase change material considering the temperature of the ocean. In addition, an electrical energy generating device that converts volume change into pressure at low temperature (1℃~2℃) in solid state and high temperature (21℃~25℃) in liquid state was fabricated. As a result of the experiment, the pressure change according to the phase change rapidly changed between 1 hour and 2 hours, and maintained a pressure of about 24MPa after 4 hours. Through this, it was confirmed that it can be used as a power source for underwater unmanned vehicles using phase change materials and temperature differences. In addition, it was found that a more improved design should be made in order to apply the phase change material to an underwater unmanned vehicle.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.9
• /
• pp.57-66
• /
• 2009

In the preliminary investigation (Park et al., 2009), the use of compressional wave velocity and its measurement techniques were proposed as a new quality control measure for trackbed fills. The methodology follows exactly the same procedure as the density control, except the density being replaced by the compressional wave velocity involving consistently with resilient modulus of design stage. The specifications for the control also include field compaction water content of optimum moisture content ${\pm}2%$ as well as the compressional wave velocity. In this sequel paper, crosshole and resonant column tests were performed as well direct-arrival method and laboratory compressional wave measurements to verify the practical applicability of a methodology far the new quality control procedure based upon compressional wave velocity. The stress-modified crosshole results reasonably well agree with the direct-arrival values, and the resonant column test results also agree well with the field crosshole results. The compressional wave velocity turned out to be an excellent control measure for trackbed fills both in the theoretical and practical point of view.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.22 no.3
• /
• pp.20-37
• /
• 2023

Although traffic signal installations are continuously expanding, the effect of preventing traffic accidents remains unverified. Totally, 7,045 traffic accident data (such as signal violations) registered with TCS were manually searched for a 7-year period from 2013 to 2019 for 1,602 traffic signals in Daejeon Metropolitan City. The top 20 traffic accident intersections were identified, the traffic accident investigation records and field maps were viewed to compare the driving direction and signal phase of the violated vehicle, and the cause of the traffic accident was divided into insufficient signal operation design (operation) and driver negligence (intentional). Results of the analysis revealed that 75% of traffic accidents occurred in thru-left-turn traffic signals and overlap; moreover, extending the yellow time or operating all red signals due to countermeasures against traffic accidents occurring in yellow signals resulted in reduced traffic accidents. Data indicated that Permissive Left Turn requires improvement with the signal operation. In addition, since The Korean National Police Agency is not computerized for traffic accident sites and signal-related data, the lack of manpower necessitates improvement and utilization of TCS when establishing traffic accident prevention measures. It is believed that it will contribute to signal operation by analyzing vast amounts of data collected in the field and presenting improvement measures.

• Composites Research
• /
• v.36 no.3
• /
• pp.211-216
• /
• 2023

When designing ships and aircraft structures, it is important to design them to satisfy weight reduction and strength. Currently, studies related to topology optimization using 3D printed composite materials are being actively conducted to satisfy the weight reduction and strength of the structure. In this study, structural analysis was performed to analyze the applicability of 3D printed composite materials to the flight control surface, one of the parts of an aircraft or unmanned aerial vehicle. The optimal topology shape of the flight control surface for the bending load was analyzed by considering three types (hexagonal, rectangular, triangular) of the topology shape of the flight control surface. In addition, the bending strength of the flight control surface was analyzed when four types of reinforcing materials (carbon fiber, glass fiber, high-strength high-temperature glass fiber, and kevlar) of the 3D printed composite material were applied. As a result of comparing the three-point bending test results with the finite element method results, it was confirmed that the flight control surface with hexagonal topology shape made of carbon fiber and Kevlar had excellent performance. And it is judged that the 3D printed composite can be sufficiently applied to the flight control surface.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.2D
• /
• pp.127-134
• /
• 2010

Tunnel sections on the highway are different from rest of sections on the highway in terms of velocity, the number of passing cars, and vehicle density which, in particular, affect drivers' behavior before and after drivers pass through the tunnel. However, literature review reveals that former studies are too focused on quantitative indicator to consider qualitative aspects. Therefore, this paper conducts survey questionnaire and IPA (Importance Performance Analysis) to find out qualitative improvements on velocity drop on the tunnel sections. The results show as follows: First, drivers require improvements of tunnel form (length and curved form inside tunnel) which is derived from long distance tunnel. Second, experts primarily ask for amendment of geometric characteristics. With comparison of requirements of both drivers and experts, there are many differences in length of tunnel and form of curved tunnel. This also presents that drivers don't satisfy with both length of tunnel and form of curved tunnel that are provided as a part of highway design factors.