• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1997년도 가을 학술발표회 논문집
• /
• pp.207-214
• /
• 1997

Current seismic design code is based on the assumption that the designed structures would be behaved inelastically during a severe earthquake ground motion. For this reason, seismic design forces calculated by seismic codes are much lower than the forces generated by design earthquakes which makes structures responding elastically. Present procedures for calculating seismic design forces are based on the use of elastic spectra reduced by a strength reduction factors known as "response modificaion factor". The effect of hysteretic behavior, as well as maximum ductility ratio and period on the inelastic strength demand is investigated. Special emphasis is given to the effects of the hysteretic characteristics such as strength degradation or pinching. Results indicate that inelastic strength demands are strongly dependent on level of inelastic deformation, period and hysteretic behavior.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1993년도 봄 학술회 논문집
• /
• pp.1-8
• /
• 1993

This paper concerns the analytical concept of tunnel design for the case where the groundwater level remains almost to a standstill even though the steady state groundwater flow occurs through tunnel drainage systems. The effect of the seepage force is considered in analysis. Two case strudies are made : the one the round shape tunnel ; the other the horse shape. The design moments, shear forces and axial forces are calculated and these results are compared to the case of water proof tunnel design as well as the case of the tunnel design without groundwater consideration.

• Coupled systems mechanics
• /
• 제2권1호
• /
• pp.23-51
• /
• 2013

An analytical algorithm for the estimation of the resistance forces exerted on the dipper of a cable shovel and the specific energy consumed in the cutting-loading process is presented. Forces due to payload and to cutting of geomaterials under given initial conditions, cutting trajectory of the bucket, bucket's design, and geomaterial properties are analytically computed. The excavation process has been modeled by means of a kinematical shovel model, as well as of dynamic payload and cutting resistance models. For the calculation of the cutting forces, a logsandwich passive failure mechanism of the geomaterial is considered, as has been found by considering that a slip surface propagates like a mixed mode crack. Subsequently, the Upper-Bound theorem of Limit Analysis Theory is applied for the approximate calculation of the maximum reacting forces exerted on the dipper of the cable shovel. This algorithm has been implemented into an Excel$^{TM}$ spreadsheet to facilitate user-friendly, "transparent" calculations and built-in data analysis techniques. Its use is demonstrated with a realistic application of a medium-sized shovel. It was found, among others, that the specific energy of cutting exhibits a size effect, such that it decreases as the (-1)-power of the cutting depth for the considered example application.

• 한국터널지하공간학회 논문집
• /
• 제17권1호
• /
• pp.49-63
• /
• 2015

본 논문에서는 가상 해저터널의 세그먼트 라이닝의 부재력 평가하여 수심별 세그먼트 최적 두께 산정 및 하중식에 따른 부재력 변화에 관한 내용을 다루었다. 가상 해저터널의 세그먼트 부재력을 평가하기 위해 먼저 다양한 설계 조건을 도출하고 이에 대해 2-Ring Beam 모델을 이용한 구조해석을 수행하여 부재력을 산출하였다. 산출한 부재력을 이용하여 예비 철근 배근을 통해 단면검토를 수행하여 각각의 지층별로 철근 배근을 조절하여 최적 두께를 산정하였다. 검토 결과를 토대로 시공조건에 따른 부재력 변화 경향을 검토하였으며 아울러 다양한 시공조건에 따른 최적 라이닝 단면을 제시하였다.

• 대한토목학회논문집
• /
• 제29권6A호
• /
• pp.641-650
• /
• 2009

파랑하중을 받는 콘크리트 부유식 구조물의 부재력 산정식을 제시하였다. 기존의 설계식은 구조물의 길이와 파장 길이가 일치할 때에 적용이 가능하다. 그러나 대부분의 경우 구조물의 길이와 파장 길이가 일치하지 않기 때문에 비평형부력에 의한 추가적인 모멘트가 발생한다. 따라서 본 연구에서는 부유구조물을 강체로 가정하고 비평형부력의 영향을 고려한 설계식을 제시하였다. 제안된 식의 타당성을 확인하기 위하여 강체거동하는 부유구조물에 대한 유한요소해석을 수행하여 이를 확인하였다. 그러나 초대형 부유구조물은 거대한 규모에 따른 유연성을 가지게 되므로 탄성거동하는 부유구조물에 대한 유한요소해석을 수행하여 강체거동에 근거한 설계식의 과대평가 양상을 파악하고자 하였다. 탄성변형을 고려하여 산정된 부재력은 강체거동으로 고려하여 산정된 부재력의 약 55%정도의 값으로 감소하는 것으로 나타났다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.281-285
• /
• 2002

A new method of dynamic contact force measurement between a pantograph and a contact wire is proposed in this paper The method does not require design modification of an original pantograph in order to install sensors such as load cells. Contact forces can be expressed as the sum of vertical shear forces at the support points and inertial forces. Using specially-designed strain gage rosettes. vertical shear forces at the supported points can be measured without noise mixing and thermal effects. In order to obtain contact forces from shear forces, 3 inertial force compansation methods are proposed and compared in this paper. By validation process, the new proposed measurement method is verified to be applicable to the on-line current collection test.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1993년도 봄 학술발표회논문집
• /
• pp.101-108
• /
• 1993

A simplified dynamic analysis method for high-rise building structures is proposed in this study. In the proposed method, member forces are obtained through static analysis using story forces derived from story shear forces which are obtained using dynamic analysis procedure. Major advantage of the proposed method is in the convenience in load combinations for design analysis.

• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.27-36
• /
• 1997

For the strength design of the brake system of a forklift truck, a procedure to calculate the internal forces acting on the system is presented in this paper. Vehicle dynamics, brake system kinematics, and internal force equilibrium analysis are integrated into the procedure. Design parameters such as stopping distance, maximum decceleration, and maximum torque generated by pedal force are considered in the vehicle dynamics, and geometric parameters of the brake system are considered in the brake system kinematics. With the two analysis results obtained, the internal forces acting in the brake system are finally calculated in the procedure.

• 한국안전학회지
• /
• 제27권3호
• /
• pp.104-110
• /
• 2012

It is a common practice to design basement walls acting as a one-way slab or plate with idealized boundary conditions, resulting in potentially inefficient design. The walls are often supported by buttress columns and side walls in the vertical direction, thereby acting as a two-way slab. In this study, structural behavior of single-story, three-span basement wall subjected to lateral soil pressure was investigated. Three dimensional finite element analyses were conducted to determine the force distribution on the wall. Based on the numerical studies, a regression analysis was carried out to determine the design values of moments in vertical and horizontal directions as well as shear forces on the wall and design charts are developed. The proposed design method with accompanying design charts would enable practicing engineers to estimate member forces on the wall for preliminary design purpose without resorting to finite element analysis. Numerical examples demonstrated the applicability of the proposed method.

• 한국철도학회논문집
• /
• 제17권6호
• /
• pp.397-401
• /
• 2014

신개념의 해상 교통 인프라인 부유식 해중철도의 합리적인 설계를 위해서는 파랑 중에 해중철도 구조체에 가해지는 유체력을 추정하여야 한다. 간편하지만 정확도 높은 유체력 추정을 위해 유체동력학 이론을 이용한 계산식을 제안하고, 수조에서 상사 모형에 대해 실험을 수행하여 비교 평가하였다. Morison식과 선형 미소진폭 파이론을 이용하여 계산된 관성력과 항력은 모형 실험 결과를 통해 계측된 유체력과 양호한 일치를 얻었다. 해중철도 구조체에 작용하는 항력은 관성력에 비해 무시할 만한 수준이었고, 파력은 파수에 따라 큰 변동을 보이지 않으나 파고에는 선형적으로 비례함을 알 수 있었다. 선형 파이론과 Morison식은 해중철도 설계 시에 간편하고 유용하게 활용될 수 있음을 확인하였다.