• Journal of the Korean Vacuum Society
• /
• v.7 no.1
• /
• pp.59-65
• /
• 1998

Multi-layer diamond-like carbon (DLC) films were deposited by 13.56 MHz r.f. PACVD method. Multi-layer DLC film was composed of 2.5 $mu extrm{m}$ thick pure DLC filml and 0.2$\mu\textrm{m}$ thick Si incorporated DLC (Si-DLC) film as a surface layer. Tribological behaviors of the multi-layer DLC film were investigated with a ball-on-disk type tribometer in ambient atmosphere using AISI 52100 steel ball. Low friction coefficient (<0.1) period increased with increasing the Si content in the surface Si-DLC film. The wear rate after 44,000 cycles and 158,400 cycles were the $2.5\times10^{-8}\sim1.8\times10^{-7}\textrm{mm}^3$/rev. and $7.1\times10^{-9}\sim1.8\times10^{-8}\textrm{mm}^3$/rev.,respectively. The wear rate of the multi-layer DLC film after 158,400 cycles was about 2 times smaller than that of pure DLC films of 2.7 $\mu\textrm{m}$ thickness. This high wear resistance and low friction coefficient was caused by the formation of Si oxide layer on the wear scar surface, as confirmed by the debris composition analysis. It was further shown that this si oxide debris layer on the wear scar surface is formed again even after removing the debris of the steel ball, which maintain the low friction coefficient between multi-layer DLC films and steel ball.

• Applied Chemistry for Engineering
• /
• v.19 no.2
• /
• pp.228-235
• /
• 2008

Nickel plating thickness increased with the electric current density, and the augmentation was more thick in $6{\sim}10A/dm^2$ than low current. Hull-cell analysis was tested to evaluate the current density. Optimum thickness was obtained at a temperature of $60^{\circ}C$, and the pH fluctuation of 3.5~4.0. Over the Nickel ion concentration of 300 g/L, plating thickness increased with the current density. The rate of decrease in nickel ion concentration was increased with the current density. The quantity of plating electro-deposition was increased at the anode surface, which was correlated with the increase of plating thickness. The plating thickness was increased because of the quick plating speed. However, the condition of the plating surface becomes irregular and the minuteness of nickel plating layer was reduced with the plating rate. After the corrosion test of 25 h, it was resulted in that maintaining low electric current density is desirable for the excellent corrosion resistance in lustered nickel plating. According to the program simulation, the thickness of diffusion layer was increased and the concentration of anode surface was lowered for the higher current densities. The concentration profile showed the regular distribution at low electric current density. The field plating process was controlled by the electric current density and the plating thickness instead of plating time for the productivity. The surface physical property of plating structure or corrosion resistance was excellent in the case of low electric current density.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.29 no.3
• /
• pp.393-408
• /
• 1996

The effect of various levels of ascidian tunic extracts and carophyll pink on the growth rate, pigmentation, lipid and total cholesterol accumulation, and fatty acid compositions were studied in kuruma prawn, Penaeus japonicus. The kuruma prawn was fed the purified diets with or without ascidian tunic extract and carophyll pink at the levels of 100, 200, and 400 ppm for 8 weeks. In the experiment diet with ascidian tunic extracts or carophyll pink, the values of daily growth rate were ranged between $1.065\;to\;1.292%$, compared with control group. The content of astaxanthin in kuruma prawn was not significantly affected by the feeding levels of tunic extracts. Feeding of the tunic extracts, on the other hand, increased the kuruma prawn lipid and total cholesterol content, and pigment deposition in concentration-dependent manners without influencing the free astaxanthin concentration of prawn flesh and heads between two feeding groups(200 and 400 ppm). And it was also demonstrated that the dietary astaxanthin was deposited in kuruma prawn body tissue mainly as astaxanthin esters. The results suggest that the best feeding strategy for pigmentation in kuruma prawns is the diets with ascidian tunic extracts at the level of 4g/kg feed (200 ppm) for 8 weeks.

• Korean journal of applied entomology
• /
• v.21 no.2 s.51
• /
• pp.87-94
• /
• 1982

The mymarids egg parasite of rice planthopper, Anagrus nr. flaveolus, were investigated to know their parasitic activities after overwitering in the paddy banks and barley fields, their host preferences and seasonal variations in the pesticide sprayed and unsprayed paddy fields of Gyeongnam province O.R.D. at Jinju from 1977 to 1979. The parasitic activities of Anagrus nr. flaveolus after overwintering in the paddy banks were high early in April and tended to decrease remarkably since mid-April by moving to the barley fields. The parasitic rate of Anagrus nr. flavelous was $47.2\~88\%$ between middle and late in April, the peak of egg deposition period. Anagrus nr. flaveolus parasitized Laodelphax striatellus, Nilaparvata lugens, and Sogatella furcifera, but didn't attack the eggs of Nephotettix cincticeps in the paddy fields. High preference was observed with Laodelphax steriatellus. The parasitic activities of Anagrus nr. flaveolus in the pesticide sprayed paddy fields were high in early July and from late August to early September. The parasitic rate in the pesticide unsprayed fields were higher than those of sprayed fields during the pesticide spraying period, from July to August and parasitic activities were active from October to before coming winter.

• Ecology and Resilient Infrastructure
• /
• v.2 no.2
• /
• pp.167-176
• /
• 2015

The water quality of the Gulpo Stream flowing through Incheon, Bucheon, Seoul, and Kimpo is getting worse due to a slow flow rate and bank constructions by stream channelization as well as an inflow of pollutants from living-sewages and factory-sewages. Besides, a dry stream phenomenon caused by a lack of maintenance water upstream makes a self-purification system worse, and the water quality of the Gulpo Stream is currently at its lowest level. The accumulated sludge of the streambed is mostly formed by the deposition of particle pollutants due to the slow flow rate and an artificially straightened stream channel. This accumulated sludge adsorbs a great quantity of organic materials and heavy metals. Because of the internal contamination possibility by a re-gushing, even after the pollution source is removed, it can cause future water pollution. Without a total examination as previously recommended, it is considered difficult to accomplish practical efficiency. In conclusion, the management of periodic sediment management such as dredging would be necessary in the Gulpo Stream because sediment could be an internal pollution source of stream water under anaerobic conditions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.6
• /
• pp.1047-1055
• /
• 2006

We patterned nano-width lines on a super hard bulk diamond substrate by varying the ion beam current and ion beam sources with a dual beam field ion beam (FIB). In addition, we successfully fabricated two-dimensional nano patterns and three-dimensional nano plate modules. We prepared nano lines on a diamond and a silicon substrate at the beam condition of 30 kV, 10 pA $\sim$ 5 nA with $Ga^+$ ion and $H_2O$ assisted ion sources. We measured each of the line-width, line-depth, etched line profiles, etch rate, and aspect ratio, and then compared them. We confirmed that nano patterning was possible on both a bulk diamond and a silicon substrate. The etch rate of $H_2O$ source can be enhanced about two times than that of Ga source. The width of patterns on a diamond was smaller than that on a silicon substrate at the same ion beam power The sub-100 nm patterns on a diamond were made under the charge neutralization mode to prevent charge accumulation. We successfully made a two-dimensional, 240 nm-width text of the 300-lettered Lord's Prayer on a gem diamond with 30 kV-30 pA FIB. The patterned text image was readable with a scanning electron microscope. Moreover, three dimensional nano-thick plate module fabrication was made successfully with an FIB and a platinum deposition, and electron energy loss spectrum (EELS) analysis was easily performed with the prepared nano plate module.

• Clean Technology
• /
• v.28 no.1
• /
• pp.1-8
• /
• 2022

To confirm the applicability of the water gas shift reaction for the production of high purity hydrogen for petroleum cokes, an unutilized low grade resource, Cu/ZnO/MgO/Al₂O₃ (CZMA), catalyst was prepared using the co-precipitation method. The prepared catalyst was analyzed using BET and H₂-TPR. Catalyst reactivity tests were compared and analyzed in two cases: a single LTS reaction from syngas containing a high concentration of CO, and an LTS reaction immediately after the syngas passed through a HTS reaction without condensation of steam. Reaction characteristics in accordance with steam/CO ratio, flow rate, and temperature were confirmed under both conditions. When the converted low concentration of CO and steam were immediately injected into the LTS, the CO conversion was rather low in most conditions despite the presence of large amounts of steam. In addition, because the influence of the steam/CO ratio, temperature, and flow rate was significant, additional analysis was required to determine the optimal operating conditions. Meanwhile, carbon deposition or activity degradation of the catalyst did not appear under high CO concentration, and high CO conversion was exhibited in most cases. In conclusion, it was confirmed that when the Cu/ZnO/MgO/Al₂O₃ catalyst and the appropriate operating conditions were applied to the syngas composition containing a high concentration of CO, the high concentration of CO could be converted in sufficient amounts into CO₂ by applying a single LTS reaction.

• Journal of the Korean Society of Radiology
• /
• v.16 no.3
• /
• pp.233-240
• /
• 2022

Research on the presence or absence of radiation shielding for FDM-type filaments has recently begun to be studied, but filaments with shielding capabilities are not sold in Korea, and not studies yet. Therefore, in this research, we will use HDPE (High Density Polyethylene) as a base material, select bismuth as a reinforcing material to manufacture a composite filament, evaluate the shielding ability, and provide basic data for the development of a radiation shielding composite material using 3D printing.A filament is produced by mixing Bismuth with an effective atomic number 83 with HDPE of PE series and adjusting the content of Bismuth to 20% wt, 30% wt, 40% wt. Compounded filaments were evaluated for their physical properties and shielding capabilities by ASTM evaluation methods. As the bismuth content increases, the density, weight, and tensile strength increase, and the shielding capacity is confirmed to be excellent. As a result of the radiation shielding capacity evaluation, it was confirmed that HDPE (80%) + Bi (20%) showed a shielding rate of 82% at 60 kV and a shielding rate of up to 94% or more at 40% bismuth content. In this study, we confirmed that it was possible to produce a radiation shield that is lighter than the metal particle-containing filaments. Furthermore, that have been shield radiation by using HDPE + Bi filaments, and radiation in the medical and radiation industries. The possibility of using it as a shielding complex was confirmed.

• Clean Technology
• /
• v.15 no.3
• /
• pp.194-201
• /
• 2009

Reductive reactivity of zero-valent iron nanoparticles was investigated for removal of nitrate-nitrogen which is considered one of the major water pollutants. To elucidate the difference in reactivity between preparation methods, iron nanoparticles were synthesized respectively from microemulsion and aqueous solution of ferric ions. Iron nanoparticles prepared from microemulsion were deposited on aluminum by electrophoretic method, and their reaction kinetics was compared to that of the same nanoparticles suspended in aqueous batch reaction. With an approximation of pseudo-first-order reaction, rate constants for suspended nanoparticles prepared from microemulsion and dilute aqueous solution were $3.49{\times}10^{-2}min^{-1}$ and $1.40{\times}10^{-2}min^{-1}$, respectively. Iron nanoparticles supported on aluminum showed ca. 30% less reaction rate in comparison with the identical nanoparticles in suspended state. However, supported nanoparticles showed the superior effectiveness in terms of nitrate-nitrogen removal per zero-valent iron input especially when excess amounts of nitrates were present. Iron nanoparticles deposited on aluminum maintained reductive reactivity for more than 3 hours, and produced nitrogen gas as a final reduction product of nitrate-nitrogen.

• Korean Chemical Engineering Research
• /
• v.61 no.4
• /
• pp.517-522
• /
• 2023

A chemical/mechanical durability test of polymer membrane evaluation method is used in which air and hydrogen are supplied to the proton exchange membrane fuel cell (PEMFC) and wet/dry is repeated in the open circuit voltage (OCV) state. In this protocol, when wet/dry is repeated, voltage increase/decrease is repeated, resulting in electrode degradation. When the membrane durability is excellent, the number of voltage changes increases and the evaluation is terminated due to electrode degradation, which may cause a problem that the original purpose of membrane durability evaluation cannot be performed. In this study, the same protocol as the department of energy (DOE) was used, but oxygen was used instead of air as the cathode gas, and the wet/dry time and flow rate were also increased to increase the chemical/mechanical degradation rate of the membrane, thereby shortening the durability evaluation time of the membrane to improve these problems. The durability test of the Nafion 211 membrane electrode assembly (MEA) was completed after 2,300 cycles by increasing the acceleration by 2.6 times using oxygen instead of air. This protocol also accelerated degradation of the membrane and accelerated degradation of the electrode catalyst, which also had the advantage of simultaneously evaluating the durability of the membrane and the electrode.