• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.6
• /
• pp.487-490
• /
• 2010

This paper describes the elecrtical and optical characteristics of $N_2$ doped porous 3C-SiC films. Polycrystalline 3C-SiC thin films are anodized by $HF+C_2H_5OH$ solution with UV-LED exposure. The growth of in-situ doped 3C-SiC thin films on p-type Si (100) wafers is carried out by using APCVD (atmospheric pressure chemical vapor deposition) with a single-precursor of HMDS (hexamethyildisilane: $Si_2(CH_3)_6)$. 0 ~ 40 sccm $N_2$ was used for doping. After the growth of doped 3C-SiC, porous 3C-SiC is formed by anodization with $7.1\;mA/cm^2$ current density for anodization time of 60 sec. The average pore diameter is about 30 nm, and etched area is increased with $N_2$ doping rate. These results are attributed to the decrease of crystallinity by $N_2$ doping. Mobility is dramatically decreased in porous 3C-SiC. The band gaps of polycrystalline 3C-SiC films and doped porous 3C-SiC are 2.5 eV and 2.7 eV, respectively.

• Journal of Korean Ophthalmic Optics Society
• /
• v.3 no.1
• /
• pp.115-120
• /
• 1998

The $TiN_x$ thin films were prepared on glass substrate by RF(radio-frequency) magnetron sputtering apparatus from a Ti target in a gaseous mixture of argon and nitrogen. In deposition, a RF power supply was used as a power source with a constant power of 240W, and the substrate was heated to $200^{\circ}C$. The films were obtained at nitrogen flow rates in the range 3-9 seem with a constant argon flow rate of 20 seem. For the films obtained, the chemical binding energy of the films was investigated by XPS (x-ray photoelectron spectroscopy) in order to analyze the chemical nature and composition of the films.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.6
• /
• pp.569-574
• /
• 2008

In the device structure of ITO/tris(8-hydroxyquinoline) aluminum ($Alq_3$)/Al device, we investigated the efficiency improvement of organic light-emitting diodes (OLEDs) depending on the hole-size of crucible boat. The device was manufactured using a thermal evaporation under the base pressure of $5{\times}10^{-6}\;Torr$. The $Alq_3$ organics were evaporated to be 100 nm thick at a deposition rate of $1.5\AA/s$, and in order to investigate the optimal surface roughness of $Alq_3$, the $Alq_3$ was thermally evaporated to be 0.8 mm, 1.0 mm, and 1.5 mm as a hole-size of the boat, respectively. We found that luminance and external quantum efficiency are superior when the hole-size of the boat is 1.0 mm. The external quantum efficiency of the device made with the hole-size of 1.0 mm boat were improved by a factor of ten compared to the devices made with the hole-size of non boat.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.5
• /
• pp.366-371
• /
• 2012

In this paper, fabricated by MEMS uncooled micro-bolometer detector for the study in the infrared sensitivity enhancement. Absorption layer SiOx-Metal series MDTF (metal-dielectric thin film) by high absorption rate and has a high thermal coefficient of resistance, low noise characteristics were implemented. Then MDTF were made in a vacuum deposition method. And MDTF for the analysis of the physical properties of silicon wafers were fabricated, TCR (temperature coefficient of resistance) value was made in order to measure the glass wafer and FT-IR (Fourier Transform Infrared spectroscopy) values were made in order to measure the germanium window. The analyzed results of MDTF -3 [%/K] has more characteristics of the TCR. And 8~12 um wavelength region close to 70% in the absorption characteristic.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.847-849
• /
• 1992

Fluorine-doped ($SnO_2$:F) thin films obtained by pyrosol deposition method have been exposed to R.F. excited pure hydrogen plasma under the following conditions; substrate temperature of 200$^{\circ}C$, $H_2$ pressure of 1 Torr, R.F. input power of 50 mW/$\textrm{cm}^{2}$, $H_2$ flow rate of 30cc/min and exposure time of 15-600 seconds. It is found that the sheet resistance of the films remains unchanged or rather slightly reduces for initial exposure time of 30-60 seconds, but increases sharply with further increasing the exposure time. The optical transmittance of $SnO_2$:F films slows a rapid fall with increasing exposure time except for a film obtained with a solution having $CH_3OH/H_2O$ mol ratio of 2.65, its degradations at the exposure time of 30-60 seconds are about 7-15%. In addition, the exposure of the films to hydrogen plasma atmosphere leads to remarkable changes in the microstructure and chemical composition, which should be attributed to the reduction of $SnO_2$ to SnO and to elemental Sn.

• Journal of the Korean Vacuum Society
• /
• v.7 no.3
• /
• pp.255-260
• /
• 1998

The ionized magnetron sputtering is very useful in filling of small metal contact or via in ULSI processing with very high ionization upto 80% based on incoming flux ratio. But fairly high sputtering gas pressure is required to get high ionization, which instead gives low deposition rate and diverse incoming neutral's angular distribution. The electron quenching by heavily sputtered metals and gas rarefaction were considered the main causes of decreased ionization in this process. RF pulsing of sputtering power was proposed to solve those two problems. The results showed that 10㎳/10 ㎳ and 100㎳/100 ㎳ of on/off pulsings were optimal pulse conditions from OES measurements and also XRD of deposited Ag film showed distinct change of (111) to (200) preferred orientation. These results were analysed in a view point of neutral gas heating and cooling by high power sputtering.

• Journal of the Korean Vacuum Society
• /
• v.8 no.3B
• /
• pp.346-352
• /
• 1999

Diamond-like carbon (DLC) lims were deposited by using end hall type ion gun. Benzene gas was used for the generation of carbon ions. In order to systematically control the ion energy, we applied to the substrate DC, pulsed DC or 250 kHz medium frequency bias voltage, DLC films of superior mechanical properties of hardness 39$\pm$4 GPa and elastic mudulus 290$\pm$50GPa (2 to 6 times better than those of the films deposited by plasma assisted CVD method) could be obtained. Deposition rate was much higher than when using Kaufman type ion source, which results from higher ion beam current of end hall type ion gun. The mechanical properties and atomic bond structure were independent of the bias voltage type ion gun. The mechanical properties and atomic bond structure were independent of the bias voltage type but intimately related with the magnitude of the bias voltage. With increasing the negative bias voltage, the structure of the films changed to graphitic one resulting in decreased content of three dimensional inter-links. Degradation of the mechanical properties with increasing bias voltage could be thus understood in terms of the content odf three dimensional inter-links.

• Journal of the Korean Vacuum Society
• /
• v.4 no.S1
• /
• pp.168-173
• /
• 1995

$GaxIn{1_x}As$ epitaxial layers were grown by a simplified hydrode vapor phase epitaxy(VPE) method bsed on the utilization of Ga/In alloy as the source metal. The effects of a wide range of experimental variables(i.e.,inlet mole fraction of HCI, deposition temperature, Ga/In alloy composition) on the ternary composition and growth rate were investigated. Layers of $Ga_{0.47}In_{0.53}As$ lattice matched to InP were successfully grown from alloys containing 5 to 8 at.% Ga. These layers were used to produce state-of-the art p-i-n photodetectors having the following characteristics: dark current, $I_d$(-5V) = 10-20 nA: responsivity, R=0.84-0.86 A/W; dark current, Id(-5V)=10-20 nA; responsivity, R=0.84-0.86 A/W; capacitance, C=0.88-0.92 pF; breakdown voltage, $V_b$ >40V. This study demonstrated for the first time that a simplified hydride VPE process with a Ga/In alloy source is capable of producing device quality epitaxial layers.

• Journal of the Korean Society of Combustion
• /
• v.7 no.3
• /
• pp.9-15
• /
• 2002

Soot generation by combustion process has been investigated with objective of understanding of chemical reaction responsible for its formation in a coaxial laminar propane jet diffusion flame. For the direct photos, as the coflowing air flow rate is reduced, the area of soot luminous zone increases at first, then becomes smaller and smaller, and even disappears. The aspects of soot deposition can be acquired by using nine $15{\mu}m$ thin SiC fibers are positioned horizontally across the flame. Deposited soots on SiC fibers show the soot inception point and growth and soot oxidation zone in a typical propane diffusion. Soot is not generated anymore in a oxidizer deficient conditions of near-extinction and flame is fully occupied by transparent blue flame. It suggests that nonsooting pyroligneous blue reaction is being dominant in a oxidizer deficient ambience. In comparison with luminosities of SiC fibers and flame itself, indirect evidence is found that the process of soot nucleation and growth is endothermic reaction. It is remarkable that there exists two adjacent regions to have antithesis characteristics; one is exothermic reaction of blue flame and another endothermic reaction zone of soot formation.

• Journal of Powder Materials
• /
• v.15 no.1
• /
• pp.1-5
• /
• 2008

ZnS-$SiO_2$ composite is normally used for sputtering target. In recent years, high sputtering power for higher deposition rate often causes crack formation of the target. Therefore the target material is required that the sintered target material should have high crack resistance, excellent strength and a homogeneous microstructure with high sintered density. In this study, raw ZnS and ZnS-$SiO_2$ powders prepared by a 3-D mixer or high energy ball-milling were successfully densified by spark plasma sintering, the effective densification method of hard-to-sinter materials in a short time. After sintering, the fracture toughness was measured by the indentation fracture (IF) method. Due to the effect of crack deflection by the residual stress occurred by the second phase of fine $SiO_2$, the hardness and fracture toughness reached to 3.031 GPa and $1.014MPa{\cdot}m^{1/2}$, respectively.