• Journal of Korean Society for Atmospheric Environment
• /
• v.15 no.5
• /
• pp.625-638
• /
• 1999

Air quality modeling for coastal urban region has been composed of a complex system including meteorological, chemical and physical processes and emission characteristics in complex terrain. In this study, we studied about an effect prediction for deposition phenomenon affecting on air quality in Pusan metopolitan metropolitan city. In air quality modeling including ship sources, a situation considered deposition process habe better result than not considered when compared with observed value. Air pollutants emitted into urban air during the daytime nearly removed through urban atmosphere polluted. Also these phenomena correlated concentration variation connent with sea/land breezes and terrain effect. Therefore we conclude that the concentration was low at daytime when deposition flux is high, and deposition effect on industrial complex and Dongrae region is considerable in particular.

• Journal of the Korean Ceramic Society
• /
• v.26 no.4
• /
• pp.539-549
• /
• 1989

Polycrystalline TiO2 thin films were deposited on Si and Al2O3 substrates by CVD method. Ethyl titanate, Ti(OC2H5)4, was used as a source material for Ti and O, and Ar was used for carrier gas. In the surface chemical reaction controlled deposition condition, the apparent activation energy of 6.74 Kcal/mole was obtained, and the atomic adsorption on substrate surface was proved to be governed by Rideal-Elley mechanism. In the mass transfer controlled deposition condition, the deposition rate was in a good agreement with the result which was calculated by the simple boundary layer theory. It was also observed that TiO2 thin films show different surface morphology according to the different deposition mechanism, which was fixed by deposition conditions. This phenomenon could be well explained by the surface perturbation theory.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.67-70
• /
• 2007

Diesel autothermal reforming has several problems such as carbon deposition in reforming reactor, sulfur poisoning of catalyst, difficulty of aromatics decomposition and mixing problems of reactants(diesel, steam, oxygen). Severe carbon deposition causes the rapid performance degradation of reformer. Carbon deposition is formed from ethylene, carbon precursor. Ethylene was generated at the homogeneous reaction zone of the reactor entrance. This phenomenon is closely linked to the mixing of reactants. In this investigation, we try to minimize the ethylene generation at the reactor entrance atomization technique.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.4
• /
• pp.751-755
• /
• 2007

We have studied the variable conditions of reactive sputtering to prepare AM thin film. The leakage current showed below $10^{-9}A/cm^2$ at the deposition temperature of $250^{\circ}C\;and\;300^{\circ}C$ in the field of 0.1 MV/cm, and it was gradually increased and to be saturated in 0.2 MV/cm. The C-V characteristics of the above mentioned deposition temperature conditions showed a deep depletion phenomenon at inversion region. The C-V characteristics showed similarly under the DC power conditions of 100 and 150 W but were degraded at 200W. When the DC power was 100, 200, and 300 W the dielectric breakdown phenomenon was shown in 2.8, 3.2 and 5.2 MV/cm, respectively. It was found that AIN film was dominated by Poole-Frenkel conduction mechanism.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.12
• /
• pp.1415-1420
• /
• 2014

3D printer is based on an additive manufacturing technology, which helps in creating the three-dimensional object using a 3D drawing. It is used in various fields, because it prints out a variety of three-dimensional products in a short period of time. In this paper, we consider a technique using the FDM(Fused Deposition Modeling) method by dissolving the ABS(Acrylonitrile Butadiene Styrene) resin among a diversity of printing technique and materials. This kind of the 3D printer prints out a product in high temperature and cools down it. In this process, a flection phenomenon is occurred according to the size of the printing product and the surrounding environment. Conventional methods for mitigating this phenomenon maintain the temperature at the optimum level, but they require using additional devices. In order to minimize the flection phenomenon in 3D printing products without additional devices, in this paper, we propose a noble technique, which creates holes on suitable positions when they are designed by 3D drawing tools. Also, we suggest mathematical model for the proposed method, and measure and analyse a printing output using a proposed technique.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.154-163
• /
• 2009

The groutability depends on the properties of the grout, its injection processes, and on the mechanical properties of the soil formation. During the process of pouring cement-based grouting into a porous medium, a variation with time occurs in the viscosity of grout suspension. In addition the particle filtration phenomenon will limit the expansion of the grouted zone because cement particles are progressively stagnant within the soil matrix. In this paper, a closed-form solution was derived by implementing the mass balance equations and the generalized phenomenological filtration law, which can be used to evaluate the deposition of cement-based grout in the soil matrix. The closed-form solution relevant to a particular spherical flow was modified by a step-wise numerical calculation, considering the variable viscosity caused by a chemical reaction, and the decrease in porosity resulting from grout particle deposition in the soil pores. A series of pilot-scale chamber injection tests was performed to verify that the developed step-wise numerical calculation is able to evaluate the injectable volume of grout and the deposition of grout particles. The results of the chamber injection tests concurred well with that of the step-wise numerical calculation. Based on the filtration phenomenon, a new groutability criterion of cement-based grout in a porous medium was proposed, which might facilitate a new insight in the design of the grouting process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.313-313
• /
• 2008

Aerosol Deposition(AD) method is based on the impact consolidation phenomenon of ceramic fine particles at room temperature. AD is promising technology for the room temperature deposition of the dielectrics thin films with high quality. Embedding of passive components such as capacitors into printed circuit board is becoming an important strategy for electronics miniaturization and device reliability, manufacturing cost reduction. So, passive integration using aerosol deposition. In this study, we examine the effects of the characteristics of raw powder on the thickness, roughness, electrical properties of $BaTiO_3$ thin films. Thin films were deposited on the copper foil and copper plate. Electrical and material properties was investigated as a change of annealing temperature. We final aim the effects of before and after of laminated on the electrical properties and suit of embedded capacitor.

• Transactions of Materials Processing
• /
• v.33 no.4
• /
• pp.277-284
• /
• 2024

Interest in remanufacturing of part has significantly increased to reduce used material and energy together. The directed energy deposition (DED) process has widely applied to remanufacturing of the part. An excessive residual stress takes place in the vicinity of the deposited region by the DED process due to rapid heating and rapid cooling (RHRC) phenomenon. The excessive residual stress decreases the reliability of the remanufactured part. Therefore, thermo-mechanical analysis for the remanufacturing of the part is needed to investigate heat transfer and residual stress characteristics in the vicinity of the deposited region. The thermo-mechanical analysis of a large volume deposition is significantly difficult to perform due to the requirement of a long computation time and a large computer memory. The goal of this paper is to investigate thermo-mechanical characteristics for remanufacturing of the ATC part using a DED process. The methodology of the thermo-mechanical analysis for a large volume deposition is proposed. From the results of analysis, heat transfer and residual stress characteristics during deposition and cooling stages are investigated. In addition, the proper deposition strategy from the viewpoint of the residual stress is discussed.

• Animal Bioscience
• /
• v.34 no.7
• /
• pp.1089-1099
• /
• 2021

With the development of sequencing technology, numerous, long noncoding RNAs (lncRNAs) have been discovered and annotated. Increasing evidence has shown that lncRNAs play an essential role in regulating many biological and pathological processes, especially in cancer. However, there have been few studies on the roles of lncRNAs in livestock production. In animal products, meat quality and lean percentage are vital economic traits closely related to adipose tissue deposition. However, adipose tissue accumulation is also a pivotal contributor to obesity, diabetes, atherosclerosis, and many other diseases, as demonstrated by human studies. In livestock production, the mechanism by which lncRNAs regulate adipose tissue deposition is still unclear. In addition, the phenomenon that different animal species have different adipose tissue accumulation abilities is not well understood. In this review, we summarize the characteristics of lncRNAs and their four functional archetypes and review the current knowledge about lncRNA functions in adipose tissue deposition in livestock species. This review could provide theoretical significance to explore the functional mechanisms of lncRNAs in adipose tissue accumulation in animals.

• Journal of Pharmaceutical Investigation
• /
• v.21 no.4
• /
• pp.201-213
• /
• 1991

There are many drugs reproted to show unusual pharmacokinetic behavior by producing a significant secondary peak in the plasma concentration-time curve after oral administration. The drugs are ranitidine, cimetidine, acetaminophen, aspirin, furosemide, bumetanide, piretanide, veralipride, sobrerol, penicillamine and doxycycline etc. Enterohepatic circulation-, two absorption site-, biphasic gastric emptying-, tissue deposition- and multi-fraction absorption theories have been suggested for the mechanisms of this phenomenon. Here, the theories were reviewed and critisized for their validity as a possible mechanism of the multiple peak phenomenon.