• 한국지반공학회논문집
• /
• 제21권4호
• /
• pp.83-98
• /
• 2005

본 연구에서는 포화 점성토지반 침하량의 합리적인 평가를 위한 새로운 개념의 응력경로법 적용방법을 제안하였다. 제안된 적용방법은 특정 점성토지반에 대해 구조물 침하와 관련하여 현장에서 나타날 수 있는 모든 응력변화 조건을 포괄하는 특성변형거동을 실험적으로 선행하여 평가한 다음, 이를 이용하여 일체의 추가적인 시험없이 발생가능한 다양한 현장조건에 대해 손쉽게 침하량을 평가하는 방법이다. 본 연구의 Part I에서는 이러한 새로운 침하량 평가개념의 실용화와 관련하여 포화 점성토지반의 침하관련 특성변형거동을 최소한의 시험만으로 효율적으로 평가하고 이를 바탕으로 임의의 응력변화 조건에 대해 손쉽게 변형거동을 예측하는 구체적인 방법을 개발하였으며, 그 적용성을 실제 사례를 통해 명확히 확인하였다.

• Corrosion Science and Technology
• /
• 제11권6호
• /
• pp.275-279
• /
• 2012

Ni-W alloy deposits have lately attracted the interest as an alternative surface treatment method for hard chromium electrodeposits because of higher wear resistance, hardness at high temperature, and corrosion resistance. This study deals with influences of process variables, such as electodeposition current density, plating temperature and pH, on the internal stress of Ni-W nanocrystalline deposits. The internal stress was increased with increasing the applied current density. With increasing applied current density, the grain size of the deposit decreases and concentration of hydrogen in the deposit increases. The subsequent release of the hydrogen results in shrinkage of the deposit and the introduction of tensile stress in the deposit. Consequently, for layers deposited at high current density, cracking occurs readily owing to high tensile stress value. By increasing the temperature of the electrodeposition from $60^{\circ}C$ to $80^{\circ}C$, the internal stress was decreased. It seems that an increase in the number of active ions overcoming the activation energy at elevated temperature caused a decline in the concentration polarization and surface diffusion. It decreased the level of hydrogen absorption due to the lessened hydrogen evolution reaction. Therefore, the lower level of hydrogen absorption degenerated the hydride on the surface of the electrode, resulting in the reduction of the internal stress of the deposits. By increasing the pH of the electrodeposition from 5.6 to 6.8, the internal stress in the deposits were slightly decreased. It is considered that the decrease in internal stess of deposits was due to supply of W complex compound in cathode surface, and hydrogen ion resulted from decrease of activity.

• 수산해양기술연구
• /
• 제51권4호
• /
• pp.576-582
• /
• 2015

The efficiencies of thermal power system using fossil fuel depend on heat exchangers which extract energy from the exhaust gas before it is expelled to the atmosphere. To increase heat transfer efficiency it is very important to maintain the surface of heat exchanger as clean condition. The accepted skill of cleaning of fouled surface of heat exchanger is soot blowing. A high pressure jet of air is forced through the flat surface of plate to remove the deposit of fouling. There is, however, little knowledge of the fundamental principles of how the jet behave on the surface and how the jet actually removes the deposit. Therefore, the study focuses on the measuring of cleaning area and cleaning dwell time after accumulating the simulated deposit on the flat surface. The deposit test rig was built for the study and simulated deposit material is used after measuring the physical property of the each material by shearing stress test. Much data was obtained for the analysis by the parameters change such as the different jet speed, different inner pressure and variable distance of the jet from the test rig surface. The experimental data was compared with the theoretical equation and most of the data matches well except some extreme cases.

• 한국표면공학회지
• /
• 제36권6호
• /
• pp.437-443
• /
• 2003

The effects of additive(grain refiner, GR) on process efficiency of the Ni-Fe-P alloy electrodeposition and the material properties of the deposit were investigated. Electrochemical properties of the deposits were investigated using polarization and electrochemical impedance techniques, and the material properties of the deposits were characterized through inductively coupled plasma(ICP), spiral contractometer, XRD, SEM and TEM. When the additive was added into the electrodeposition bath, current efficiency, Ni content and corrosion resistance of the deposit increased, whereas residual stress, surface roughness and grain size of the deposit decreased.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2003년도 Proceedings of the international symposium on the fusion technology
• /
• pp.642-647
• /
• 2003

Palladium is widely used for several applications and recovery of palladium from secondary sources becomes increasingly important since palladium is one of maldistributed platinum group metals. Electrochemical recovery of dense palladium metal sheet from Pd leaching solution is a simple and easily controlled method. The surface morphology of the recovered Pd metal was significantly affected by current density and temperature. Dense deposit morphology was in higher stress state regardless of preparation condition under $55^{\circ}C$. Rising temperature up to $70^{\circ}C$ had a stress releasing effect besides densification of Pd deposit.

• 자원리싸이클링
• /
• 제14권1호
• /
• pp.55-63
• /
• 2005

This study investigated the electrochemical recovery of palladium in a HCl solution that is used for palladium leaching. The high acidity of HCl solution and the low concentration of Pd ions increased the cathodic overpotential and reduced the limiting current density. Lowering the current density produced dense deposits; however, they were under high tensile stress. Raising the temperature affected both the densification and the stress, which enabled the attainment of dense Pd deposits under low stress. Lowering the current density and raising the temperature up to 70$^{\circ}C$ was recommended for the recovery of palladium as sound bulk Pd deposits. Current efficiency was over 85% at the initial stage of recovery may decrease the current efficiency, since a low Pd ion concentration results in a low limiting current density.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.161-166
• /
• 2001

Overconsolidated clays have a different stress history according to the deposit environment. The stress history is classified into (i) rotation angle of stress path, (ii) overconsolidation ratio, and (iii) magnitude of length of recent stress path. Stress-strain behaviour of overconsolidated clays strongly depends on these stress history. In this study a series of drained stress path tests were carried out. Test results indicated that stress-strain behaviour of overconsolidated clay(focused on strain rate) depends on OCR and length of recent stress path, especially rotation angle.

• 한국지반공학회지:지반
• /
• 제9권3호
• /
• pp.23-34
• /
• 1993

지반조건이 개단강관말뚝의 거동에 미치는 영향을 규명하기 위하여 응력상태와 상대밀도의 조절이 가능한 토조내에 포설된 모래지반에서 모형말뚝실험이 수행되었다. 모형말뚝은 개단강관 말뚝의 각 부분에 작용하는 지지력을 분리측정하기 위하여 직경이 다른 두개의 파이프로 만들어졌다. 실험결과에 의하면 모래지반에 타입된 개단말뚝의 폐색정도와 관입저항력은 지반의 수직응력보다는 수평응력과 상대밀도에 의하여 좌우되었으며, 관내토지지력과 외주면마찰력, 그리고 전체 지지력도 수직응력보다는 수평응력과 상대밀도에 의하여 주로 영향받는 것으로 나타났다. 또 한 말뚝 외벽에 작용하는 수평응력은 원지반의 응력상태와는 관계없이 조밀한 지반의 경우에는 원지반의 수평응력보다 크게, 보통상태의 지반에서는 원지반과 비슷하게, 그리고 매우 느슨한 지반에서는 원지반보다 작게 측정되었다. 원지반의 수평응력에 대한 말뚝 설치후의 말뚝 외벽에 작용하는 수평응력의 비는 주어진 모래지반의 경우 원지반의 수평응력과 관계없이 상대밀도에 따라 일정한 값으로 나타났다.

• 동력기계공학회지
• /
• 제5권3호
• /
• pp.88-94
• /
• 2001

Stellite 12 alloy-powders were overlaid on 410 stainless steel valve seat using plasma transferred arc(PTA) process. Variation of the microstructure, hardness, wear and corrosion of overlaid deposit with current change was investigated. The deposit showed hypoeutectic microstructure, which was consisted of primary cobalt dendrite and networked $M_7C_3$ type eutectic carbides. As current increased, the amount of eutectic carbide decreased and its dendritic secondary arm spacing increased. Hardness of the deposit was decreased with increase of current. Stress relief heat treatment at $600^{\circ}C$ for two hours resulted in slight increase of hardness in the deposit and showed uniform hardness distribution in base metal without any hardened layer in HAZ. Specific wear decreased with increase of sliding distance. The deposit of high hardness with a lot of eutectic carbide showed relatively low specific wear. Initial corrosion current density of the deposit in 0.1N sulfuric acid was lower than those of 410 stainless steel, and showed a little variation with PTA current.

• Journal of Advanced Marine Engineering and Technology
• /
• 제19권4호
• /
• pp.42-50
• /
• 1995

To study the effect of welding methods on the Stress Corrosion Cracking (SCC) behavior of welded AISI type 316L and 304 austenitic stainless steel, the Slow Strain Rate Technique(SSRT) has been adopted in the boiling 45 wt% $MgCl_2$ solution. The results are as follows. 1) Welded sections are more susceptible than base metal in SCC, and the rank of SCC, and the rasistance in welding method is TIG, MIG, $CO_2$ and ARC. 2) The Ultimate tensile strength(UTS) and the strain of both base metal and welded joint are reduced as decreasing extension rate. 3) The SCC resistance of 316L base metal and welded sections are superior than that of 304. 4) The tendency of pitting and the SCC suseptibility are agreed well, and the SCC site is welded deposit section in 316L whereas HAZ in 304.