• 한국지구과학회지
• /
• 제26권2호
• /
• pp.114-128
• /
• 2005

Fuzzy information representation of multi-source spatial data is applied to landslide hazard mapping. Information representation based on frequency ratio and non-parametric density estimation is used to construct fuzzy membership functions. Of particular interest is the representation of continuous data for preventing loss of information. The non-parametric density estimation method applied here is a Parzen window estimation that can directly use continuous data without any categorization procedure. The effect of the new continuous data representation method on the final integrated result is evaluated by a validation procedure. To illustrate the proposed scheme, a case study from Jangheung, Korea for landslide hazard mapping is presented. Analysis of the results indicates that the proposed methodology considerably improves prediction capabilities, as compared with the case in traditional continuous data representation.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 춘계 학술논문 발표대회
• /
• pp.182-183
• /
• 2017

This research identifies radon gas absorption mechanism by adsorption materials, replacing gypsum board with radon emissions, the density and absorption rates of magnesium were carried out using vermiculite, anthracite, powdered active carbon, bentonite, illite, diatomite as a basic study on the fire resistance type of radon Gas reduction type with absorption and decomposition. As a result of the experiment, diatomite showed the lowest density, and the highestt value was the highest. For the absorption rate, bentonite showed the highest absorption rate, and the anthracite showed the lowest absorption rate.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.21-23
• /
• 2002

We designed and manufactured helical magnetic flux compression generator, in which, the current density was reduced by increasing the number of wires by stages, and the voltage between wires was reduced by decreasing the time rate of inductance change. The figure of merit and the energy multiplication ratio of the generator were measured as a function of current density flowing through coil and their characteristics were analyzed. When the current density of coil was more than 250 kA/cm, the figure of merit and the energy multiplication ratio were decreased rapidly.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.50-50
• /
• 2011

The aluminum nitride films were prepared by RF magnetron sputtering using an AlN ceramic target. The crystallinity, grain size, Al-N bonding and thermal conductivity were investigated in dependence on the plasma power densities (4.93, 7.40, 9.87 W/$cm^2$) during sputtering. High thermal conductivity is important properties of A1N passivation layer for functioning properly in thermal inkjet printhead. The crytallinity, grain size, Al-N bonding formation and chemical composition were observed using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS), respectively. The AlN thin film was changed from amorphous to crystalline as the power density was increased, and the largest grain size appeared at medium power density. The near stoichiometry Al-N bonding ratio was acquired at medium power density. So, we know that the AlN thin film had better thermal conductivity with crystalline phase and near stoichometry Al-N bonding ratio at 7.40 W/$cm^2$ power density.

• Applied Science and Convergence Technology
• /
• 제23권2호
• /
• pp.90-96
• /
• 2014

Flexible $ZrO_2$ films as dielectric materials for high-energy-density capacitors were deposited on polyethylene terephthalate (PET) substrates by RF magnetron sputtering. The growth behavior, microstructure and electrical properties of the flexible $ZrO_2$ films were dependent on the sputtering pressure and gas ratio. Although $ZrO_2$ films were deposited at room temperature, all films showed a tetragonal crystalline structure regardless of the sputtering variables. The surface of the film became a surface with large white particles upon an increase in the $O_2/Ar$ gas ratio. The RMS roughness and crystallite size of the $ZrO_2$ films increased with an increase in the sputtering pressure. The electrical properties of the $ZrO_2$ films were affected by the microstructure and roughness. The $ZrO_2$ films exhibited a dielectric constant of 21~38 at 1 kHz and a leakage current density of $10^{-6}{\sim}10^{-5}A/cm^2$ at 300 kV/cm.

• 한국세라믹학회지
• /
• 제37권8호
• /
• pp.824-831
• /
• 2000

Alumina tapes, having various ratios of alumina to alumina＋binder＋plasticizer (a/(a＋o)) and binder to binder＋plasticizer(b/(b＋p)), were prepared by the tape casting method. The tapes were thermocompressed varying the thermocompression parameters such as temperature, pressure, and duration time. Among the parameters, the pressure was the most influential to the tape packing density. The packing density varied in two different ways depending on the a/(a＋o) ratio. For the tapes having low a/(a＋o) ratio, a saturation density was reached by applying very a low pressure of 1 MPa. For tapes with high a/(a＋o), on the contrary, the saturation density was obtained at a relatively high pressure. These different responses to the pressure are attributed to the fact that the rearrangement of alumina particles by the pressure becomes easy as an organic content in the tapes is high.

• Journal of the Korean Data and Information Science Society
• /
• 제25권3호
• /
• pp.623-632
• /
• 2014

We shall consider the estimation for the parameter and the right tail probability in a general exponential distribution. We also shall consider the estimation of the reliability P(X < Y ) and the skewness trends of the density function of the ratio X=(X+Y) for two independent general exponential variables each having different shape parameters and known scale parameter. We then shall consider the estimation of the failure rate average and the hazard function for a general exponential variable having the density function with the unknown shape and known scale parameters, and for a bivariate density induced by the general exponential density.

• Journal of the Korean Wood Science and Technology
• /
• 제41권2호
• /
• pp.105-110
• /
• 2013

A repeated impregnation and carbonization process was performed to prepare high-density woodceramics using MDF. The physical properties were estimated to further confirm morphologically structurally occurred changes of one-time and two-time phenolic resin treated and carbonized woodceramics. As compare one-time and two-time carbonized woodceramics, the increasing rate of weight and density declined after second carbonization as the resin impregnation ratio grew higher, and when the resin impregnation ratio was 40 percent, the weight and density of the second carbonization increased more than in the first step by 20.5% and 33.9% respectively which were the highest rates.

• 한국정밀공학회지
• /
• 제9권2호
• /
• pp.29-35
• /
• 1992

The distribution of magnetic flux density of electro-magnetic chucks may clarify the clamping characteristics which are strongly related to the machining efficiency and machining accuracy in a surface grinder. Therefore the distribution of the normal and the tangential components of magnetic flux density has been analyzed theoretically. It appears that the normal and the tangential components of magnetic flux density increase as the ratio of the separator width to the pitch e/p decreases. The results seem to increase the uniformity and stability of normal component of magnetic flux density for the decreased e/p.

• 한국산림과학회지
• /
• 제104권3호
• /
• pp.411-420
• /
• 2015

이 연구는 우리나라 서 남 동해안 및 제주도 총 123개소의 곰솔 해안방재림 실태조사 결과와 국내 외 사례와의 비교를 토대로 형상비를 고려한 밀도 관리의 필요성과 방안을 검토하기 위하여 실시하였다. 곰솔의 형상비(수고/흉고직경)는 서 남 동해안에서 임목밀도와 정의 상관을 보이며, 서해안은 평균 66.32로 남해안 49.57, 동해안 48.19 및 제주도 48.29에 비하여 현저히 높은 것으로 나타났다. 특히 서해안은 형상비 70이상인 곰솔 임분이 전체 개소수의 50%를 차지하여, 국내 외 사례와 비교할 때 방재기능의 저하가 우려되었다. 임목밀도는 동해안을 제외한 대부분 지역에서 우리나라 산림청 및 일본 삼림총합연구소의 기준보다 현저히 높은 과밀상태를 보여 밀도조절이 필요한 것으로 판단되었다. 우리나라 해안지역 곰솔의 생장 추정식에 의하면 해안방재림의 기능 저하를 방지하기 위하여 형상비가 급증하는 14년생 이하의 유령림에 대한 밀도관리가 중요한 것으로 시사되었다. 특히 곰솔림의 1차 솎아베기는 형상비 70을 초과하는 8년생 임분이 되기 전에 실시해야 할 것으로 판단되었다. 우리나라와 일본의 곰솔 밀도기준을 비교한 결과, 목재생산을 목표로 한 국내의 곰솔 밀도기준에 비하여 형상비를 고려한 일본의 기준은 방재기능이 비교적 취약한 흉고직경 20 cm이하의 유령림에 대해서는 보다 높은 임목밀도를 요구하는 것으로 나타났다. 현재 우리나라에는 곰솔 해안방재림의 적정 밀도기준이 없기 때문에 현지조사 결과를 토대로 방재기능에 중점을 두고 설정된 일본의 기준이 유효하게 활용될 수 있다고 판단되었다.