• Environmental Sciences Bulletin of The Korean Environmental Sciences Society
• /
• 제10권S_4호
• /
• pp.181-187
• /
• 2001

This study was carried out to measure the variations of potential and current density with polymers. The results were particularly examined to identify the influences on potential and rate of various factors including temperature and pH. The Tafel slope for anodic dissolution was determined by the polarization effect depending on these conditions. The optimum conditions were established for each case. The second anodic current density peak and maximum current density were designated as the relative polarization sensitivity$(I_r/I_f)$. The mass transfer coefficient value$(\alpha)$ was determined with the Tafel slope for anodic dissolution based on the polarization effect with optimum conditions.

• 생태와환경
• /
• 제43권4호
• /
• pp.513-517
• /
• 2010

The diel swarming of Moina macrocopa and the relationship between environmental factors were evaluated in a shallow reservoir. The littoral density of Moina macrocopa maintained low from night to noon, reached maximum density at the afternoon with compact swarms at the waters' edge, and dispersed after sunset. The recruitment of Moina macrocopa and changes of water temperature (r=0.709, p<0.001) and juvenile fish density (r=0.511, p=0.002) in the littoral zone showed a significant positive relationships. After the induction of diel horizontal migration toward littoral zone, therefore, direct juvenile fish predation pressure should be induced Moina macrocopa swarming.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2005년도 동계학술발표대회 논문집
• /
• pp.311-316
• /
• 2005

The experimental study for an operational characteristics and performance of the sodium heat pipe were carried out. For an experiment. the heat pipe which is 1000mm length and 25.4mm diameter of stainless steel container with 50 mesh of screen wick using sodium as a working fluid is manufactured and tested as functions of heat flow rate, inclined angle and operating temperature. The test results are as follows. During the start-up. frontal start up was observed because of the vapor density increasing as increased the hot zone. Also, the heat pipe showed uniform temperature over than $420^{\circ}C$ of the operating temperature. The average heat transfer coefficient increased as the heat flux and the vapor temperature increase, and the range of the total thermal resistance was 0.075-0.04 $^{\circ}C/W$ at the 12-53.55 $kW/m^2$ of heat flux and $500-750^{\circ}C$of operating temperature. The maximum heat flow rate was 750W at the 10 degree of top heating mode.

• 한국표면공학회지
• /
• 제13권3호
• /
• pp.146-154
• /
• 1980

The effects of various electrodeposition conditions (deposition temperature and cathode current density) on preferred orientation and microhardness of electrodeposited Ni-Sn and Sn-Zn alloys were studied. At deposition temperatures from 25$^{\circ}$ to 95$^{\circ}C$ and constant cathode current density of 270 and 530 A/$m^2$ Ni-Sn and Sn-Zn were codeposited in chloride-fluoride acid and stannate-cyanide alkaline electrolyte bath respectively. Ni-Sn alloy deposited at temperatures from 25$^{\circ}$ to 35$^{\circ}C$ was composed of single phase of $Ni_3Sn_4$ with 73 wt.% Sn and the one deposited at temperatures from 45$^{\circ}$ to 95$^{\circ}C$ was made of multiphase mixture of NiSn, $Ni_3Sn_2$ and $Ni_3Sn_4$ with nearly equiatomic composition (65.5 wt.% Sn). The random orientation of thermody-namically metastable NiSn phase (hexagonal structure) predominated at deposition temperature range 25$^{\circ}$-45$^{\circ}C$, and the strong (110) preferred orientation was found at 65$^{\circ}$-85$^{\circ}C$ and then disappeared again at 95$^{\circ}C$. The microhardness of Ni-Sn deposits increased with deposition temperature up to 85$^{\circ}C$, and then decreased at constant cathode current density. The preferred orientation and the maximum microhardness were discussed in terms of lattice contractile stress which result from desorption of hydrogen atom absorbed in deposit lattice. The Sn content of Sn-Zn alloy deposits increased with deposition temperature up to 75$^{\circ}C$, and then decreased at constant cathode current density of 530 A/$m^2$. It also decreased with cathode current density up to 530 A/$m^2$, and then increased at constant deposition temperature of 25$^{\circ}C$. Sn-Zn alloy deposits were composed of two-phase mixture of ${beta}$-Sn and Zn. The preferred orientations of ${beta}$-Sn (tetragonal structure) changed with deposition temperature. The microhardness of Sn-Zn deposits decreased with deposition temperature. It also increased with cathode density up to 530 A/$m^2$, and then decreased at constant deposition temperature of 25$^{\circ}C$. The microhardness of Sn-Zn deposits was observed to be determinded more by the Sn content than by the preferred orientation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.1140-1140
• /
• 2015

In this paper, the MIM thin films were deposited on Si substrate by sputtering method. And MIM thin films were annealed at $400{\sim}600^{\circ}C$ using RTA. The capacitance density of MIM thin films were increased with the increase of annealing temperature. The maximum capacitance density of $0.62{\mu}F/cm^2$ was obtained by annealing temperature at $600^{\circ}C$. The voltage dependence of dielectric loss showed about 0.03 in voltage ranges of -10~+10 V.

• 한국전기전자재료학회논문지
• /
• 제11권10호
• /
• pp.784-789
• /
• 1998

In this work, the optical properties of freestanding GaN single crystalline substrate grown by hydride vapor phase epitaxy(HVPE) were investigated. The low temperature PL spectrum in freestanding GaN consists of free and bound exciton emissions, and a deep DAP recombination around at 1.8eV. The optically-pumped stimulated emission in freestanding GaN substrate was observed at room temperature. At the maximum power density of 2MW/$\textrm{cm}^2$, the peak energy and FEHM of stimulated emission were 3.318 eV and 8meV, respectively. The excitation power dependence on the integrated emission intensity indicates the threshold pumping power density of 0.4 MW/$\textrm{cm}^2$.

• 대한전기학회논문지
• /
• 제41권5호
• /
• pp.492-501
• /
• 1992

In this paper, an ion analyzer is used in conjunction with a Langmuir probe to study the chracteristics of ECR plasma such as the ion temperature, ion current density and electron temperature as the operating pressure, ${\mu}$-wave power and axial position change, Silicon etching has been performed with RF-biasing and its etching chracteristics have been discussed in terms of the ion energy distribution function. The maximum value of ion current density appears in the range of 10S0-3T mbar and the broadening of ion energy distribution function increases as pressure increases. Therefore, as pressure decreases, anisotropy increases but selectivity to photoresist decreases.

• 한국환경과학회지
• /
• 제26권11호
• /
• pp.1247-1253
• /
• 2017

The Fuji variety of apple, introduced in Japan, has excellent storage quality and good taste, such that it is the most commonly cultivated apple variety in Gunwi County, North Gyeongsang Province, Korean Peninsula. Accurate prediction of harvest maturity allows farmers to more efficiently manage their farm in important aspects such as working time, fruit storage, market shipment, and labor distribution. Temperature is one of the most important factors that determine plant growth, development, and yield. This paper reports on the beta distribution (function) model that can be used to simulate the the phenological response of plants to temperature. The beta function, commonly used as a skewed probability density in statistics, was introduced to estimate apple harvest maturity as a function of temperature in this study. The model parameters were daily maximum temperature, daily optimum temperature, and maximum growth rate. They were estimated from the input data of daily maximum and minimum temperature and apple harvest maturity. The difference in observed and predicted maturity day from 2009 to 2012, with optimal parameters, was from two days earlier to one day later.

• 신재생에너지
• /
• 제18권4호
• /
• pp.12-21
• /
• 2022

The pyrolysis characteristics of high-density polyethylene (HDPE), low-density polyethylene (LDPE), and polypropylene (PP) were analyzed numerically using a 1D plug flow reactor (PFR) model. A lumped kinetic model was selected to simplify the pyrolysis products as wax, oil, and gas. The simulation was performed in the 400-600℃ range, and the plastic pyrolysis and product generation characteristics with respect to time were compared at various temperatures. It was found that plastic pyrolysis accelerates rapidly as the temperature rises. The amounts of the pyrolysis products wax and oil increase and then decrease with time, whereas the amount of gas produced increases continuously. In LDPE pyrolysis, the pyrolysis time was longer than that observed for other plastics at a specified temperature, and the amount of wax generated was the greatest. The maximum mass fraction of oil was obtained in the order of HDPE, PP, and LDPE at a specified temperature, and it decreased with temperature. Although the 1D model adopted in this study has a limitation in that it does not include material transport and heat transfer phenomena, the qualitative results presented herein could provide base data regarding various types of plastic pyrolysis to predict the product characteristics. These results can in turn be used when designing pyrolysis reactors.

• 한국전산유체공학회지
• /
• 제16권3호
• /
• pp.15-21
• /
• 2011

Aerothermodynamic flowfields of aircraft engine nozzles are computationally investigated at various flight conditions for infrared signature analysis. A mission profile of subsonic unmanned combat aerial vehicle is considered for the case study and associated engine and nozzles are selected through a performance analysis. Computational results of nozzle and plume flowfields using a density-based CFD code are analyzed in terms of thrust, maximum temperature, length and optical thickness of plume. It is shown that maximum temperature, length, and optical thickness of nozzle plume increase for lower altitude and higher Mach number.