• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.44 no.1
• /
• pp.49-62
• /
• 2024

Reckless development of the underground by rapid urbanization causes inspection delay on replacement of existing structure and installation new facilities. However, frequent accidents occur due to deviation in construction design planned by inaccurate location information of underground structure. Meanwhile, the electrical resistivity survey, knowns as non-destructive method, is based on the difference in the electric potential of electrodes to measure the electrical resistance of ground. This method is significantly advanced with multi-electrode and deep learning for analyzing strata. However, there is no study to quantitatively assess change in electrical resistance according to geometric conditions of structures. This study evaluates changes in electrical resistance through geometric parameters of electrodes and structure. Firstly, electrical resistance numerical module is developed using generalized mesh occurring minimal errors between theoretical and numerical resistance values. Then, changes in resistances are quantitatively compared on geometric parameters including burial depth, diameter of structure, and distance electrode and structure under steady current condition. The results show that higher electrical resistance is measured for shallow depth, larger size, and proximity to the electrode. Additionally, electric potential and current density distributions are analyzed to discuss the measured electrical resistance around the terminal electrode and structure.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.13 no.4
• /
• pp.2456-2470
• /
• 1971

Compaction of soil is very important for construction of soil structures such as highway fills, embankment of reservoir and seadike. With increasing compaction effort, the strength of soil, interor friction and Cohesion increas greatly while the reduction of permerbilityis evident. Factors which may influence compaction effort are moisture content, grain size, grain distribution and other physical properties as well as the variable method of compaction. The moisture content among these parameter is the most important thing. For making the maximum density to a given soil, the comparable optimum water content is required. If there is a slight change in water content when compared with optimum water content, the compaction ratio will decrease and the corresponding mechanical properties will change evidently. The results in this study of soil compaction with different water content are summarized as follows. 1) The maximum dry density increased and corresponding optimum moisture content decreased with increasing of coarse grain size and the compaction curve is steeper than increasing of fine grain size. 2) The maximum dry density is decreased with increasing of the optimum water content and a relationship both parameter becomes rdam-max=2.232-0.02785 $W_0$ But this relstionship will be change to $r_d=ae^{-bw}$ when comparable water content changes. 3) In case of most soils, a dry condition is better than wet condition to give a compactive effort, but the latter condition is only preferable when the liquid limit of soil exceeds 50 percent. 4) The compaction ratio of cohesive soil is greeter than cohesionless soil even the amount of coarse grain sizes are same. 5) The relationship between the maximum dry density and porosity is as rdmax=2,186-0.872e, but it changes to $r_d=ae^{be}$ when water content vary from optimum water content. 6) The void ratio is increased with increasing of optimum water content as n=15.85+1.075 w, but therelation becames $n=ae^{bw}$ if there is a variation in water content. 7) The increament of permeabilty is high when the soil is a high plasticity or coarse. 8) The coefficient of permeability of soil compacted in wet condition is lower than the soil compacted in dry condition. 9) Cohesive soil has higher permeability than cohesionless soil even the amount of coarse particles are same. 10) In generall, the soil which has high optimum water content has lower coefficient of permeability than low optimum water content. 11) The coefficient of permeability has a certain relations with density, gradation and void ratio and it increase with increasing of saturation degree.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.5
• /
• pp.822-828
• /
• 2012

Organic fruit production has increased due to consumer's interest and government's political support for environmentally-friendly agriculture. The aim of this study was to investigate the effects of cover plants on soil microbial community and establish the fruit cultivation method by organic farming techniques. Cover plants used as an organic nutrient source in an apple orchard were rye and barley, the Gramineae and red clover and hairy vetch, the Leguminosae. In the effects of cover plants on the soil chemical characteristics, the soil pH values were higher than that of conventional organic pear orchard. The content of P showed no significant difference between control and cover plant plots. Organic matter level was similar in control and Gramineae cover plant plots, while organic matter content in cover plants belong to Leguminosae was lower than that of control plot. K content was lower in the plots treated with rye and red clover than control plot, while K content in hairy vetch treated plot was higher than control plot. Ca content was lower in control plot than in cover plant treated plots. Concentrations of Mg in the plots treated with barley and hairy vetch was lower than control plot. In August rye and red clover covered soil showed higher bacterial community density than that of control soil and barley treated soil showed highest Actinomycetes community density among treatments. Barley and hairy vetch soils showed higher level of fungi community density than that of control soil in August. In pyrosequencing analysis barley treated soil showed highest distribution ratio of Actinomycetes among treatment. Our findings might be used as basic data for choosing cover plant with effective organic matter decomposition and nutrition supply capacity.

• Journal of Biomedical Engineering Research
• /
• v.24 no.5
• /
• pp.401-410
• /
• 2003

This study investigates the biomechanical efficacies of various cement augmentation techniques with or without pressurization for varying degrees of osteoporotic femur. For this study, a biomechanical analysis using a finite element method (FEM) was undertaken to evaluate surgical procedures, Simulated models include the non-cemented(i.e., hip screw only, Type I), the cement-augmented(Type II), and the cemented augmented with pressurization(Type III) models. To simulate the fracture plane and other interfacial regions, 3-D contact elements were used with appropriate friction coefficients. Material properties of the cancellous bone were varied to accommodate varying degrees of osteoporosis(Singh indices, II∼V). For each model. the following items were analyzed to investigate the effect surgical procedures in relation to osteoporosis of varying degrees : (a) von Mises stress distribution within the femoral head in terms of volumetric percentages. (b) Peak von Mises stress(PVMS) within the femoral head and the surgical constructs. (c) Maximum von Mises strain(MVMS) within the femoral head, (d) micromotions at the fracture plane and at the interfacial region between surgical construct and surrounding bone. Type III showed the lowest PVMS and MVMS at the cancellous bone near the bone-construct interface regardless of bone densities. an indication of its least likelihood of construct loosening due to failure of the host bone. Particularly, its efficacy was more prominent when the bone density level was low. Micromotions at the interfacial surgical construct was lowest in Type III. followed by Type I and Type II. They were about 15-20% of other types. which suggested that pressurization was most effective in limiting the interfacial motion. Our results demonstrated the cement augmentation with hip screw could be more effective when used with pressurization technique for the treatment of intertrochanteric fractures. For patients with low bone density. its effectiveness can be more pronounced in limiting construct loosening and promoting bone union.

• Progress in Medical Physics
• /
• v.25 no.3
• /
• pp.143-150
• /
• 2014

In general radiotherapy, mega-voltage (MV) x-ray images are widely used as the unique method to verify radio-therapeutic fields. But, the image quality of MV images is much lower than that of kilo-voltage x-ray images due to scatter interactions. Since 1990s, studies for the scatter correction have performed with digital-based MV imaging systems. In this study, a novel method for the scatter correction is suggested using scatter to primary ratio (SPR), instead of conventional methods such as digital image processing or scatter kernel calculations. We measured two MV images with and without a solid water phantom describing a patient body with given imaging conditions, and calculated un-attenuated ratios. Then, we obtained SPR distributions for the scatter correction. For experimental validation, a line-pair (LP) phantom using several Al bars and a clinical pelvis MV image was used. As the result, scatter signals of the LP phantom image were successfully reduced so that original density distribution of the phantom was restored. Moreover, image contrast values increased after SPR correction at all ROIs of the clinical image. The mean value of increases was 48%. The SPR correction method suggested in this study has high reliability because it is based on actually measured data. Also, this method can be easily adopted in clinics without additional cost. We expected that the SPR correction can be an effective method to improve the quality of MV image guided radiotherapy.

• Journal of Korean Society of Forest Science
• /
• v.105 no.1
• /
• pp.42-47
• /
• 2016

To examine the natural regeneration in the natural mixed-broadleaved forest, flowering, fruiting, seed-fall, and seed viabilities of Acer pseudosieboldianum (Ap) were investigated in Mt. Jungwang, Gangwon-do, from 2009 to 2015. The flower of Ap consisted many male and bisexual flowers on the corymb. Flowering dates are differed between sex morph in the same inflorescence. Stamens are stop growing and disappeared after pollinated pistil begin to grow in bisexual flowers, and male flowers have vestial pistil. The flowers of Ap might be pollinated by Apis mellifera, Andrenidae spp. and Syrphinae spp. Ap had some mechanism to prevent from self pollination with heterodichogamy. Mean annual seedfall of Ap was 70,780 ea/ha (ranged 310~234,840 ea/ha). Annual seedfall of Ap varied severely, and the maximum was about 760 times the minimum. Annual seed production of Ap might be to a normal distribution. Rates of damaged or decayed seeds are highest 59.3%, and those of sound seeds are 23.9%, Those of undeveloped and empty seeds are 9.2% and 7.6%, respectively. The most important factors influencing sound seed production might be the density and activities of insect pollinators and sucking pest in the flowerwing period, middle-late May. Successful regeneration of Ap might be in masting year and on the gap sites with proper conditions to germinate and grow. To understand the natural regeneration of deciduous hardwoods, further study on the characteristics of flowering and fruiting, pre- and post-dispersal seed predation, and annual variation on these factor should be needed.

• Journal of Korean Society of Transportation
• /
• v.28 no.3
• /
• pp.131-143
• /
• 2010

This study has aimed to develop accident modification factor(AMF) for rural two-lane roadway segments. Accident Modification Factor is a coefficient to assess roadway safety as reflecting characteristics of homogeneous roadway. It estimates accident frequency of roadway segments with developed base model and exposure. We found on items of such factors as crosswalk, driveway density, topography characteristic, land use and median through statistical models and literature review. To develop accident modification factors, we used statistical model methods and analyses of applicability and expert judgement method were practiced to validate it. Although expert judgement for land use item was questionable, most items were rated acceptable. Result of comparative analysis revealed crash frequencies of IHSDM and KHSEM were most similar with actual. However, accident distribution of KHSEM was more proper than IHSDM. Also overall estimated values of RSDS were found to be overestimated.

• Journal of KIISE:Software and Applications
• /
• v.31 no.12
• /
• pp.1684-1690
• /
• 2004

This paper presents a method for classifier selection that uses distribution information of the training samples in a small region surrounding a sample. The conventional DCS-LA(Dynamic Classifier Selection - Local Accuracy) selects a classifier dynamically by comparing the local accuracy of each classifier at the test time, which inevitably requires long classification time. On the other hand, in the proposed approach, the best classifier in a local region is stored in the FSA(Feature Space Attribute) table during the training time, and the test is done by just referring to the table. Therefore, this approach enables fast classification because classification is not needed during test. Two feature space attributes are used entropy and density of k training samples around each sample. Each sample in the feature space is mapped into a point in the attribute space made by two attributes. The attribute space is divided into regular rectangular cells in which the local accuracy of each classifier is appended. The cells with associated local accuracy comprise the FSA table. During test, when a test sample is applied, the cell to which the test sample belongs is determined first by calculating the two attributes, and then, the most accurate classifier is chosen from the FSA table. To show the effectiveness of the proposed algorithm, it is compared with the conventional DCS -LA using the Elena database. The experiments show that the accuracy of the proposed algorithm is almost same as DCS-LA, but the classification time is about four times faster than that.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.247-253
• /
• 1996

Microscopic analysis has been performed in order to investigate effects of the microstructure of the starting feed rods on the morphology of the S-L interface and the stability of the molten zone during single crystal growth of $SrTiO_{3}$ using a floating zone method. Undoped and $Fe_{2}O_{3}$ doped $SrTiO_{3}$ doped $SrTiO_{3}$ specimens, sintered at the different temperatures have been used. In the case of the feed rods sintered at the lower temperature($1400^{\circ}C$), the poor densification made the stability of the molten zone difficult to maintain. The feed rods sintered at the higher temperature ($1600^{\circ}C$) exhibited the higher density but their molten zone was difficult to maintain due to the presence of the abnormally grown grains. It is concluded that the uniform grain size distribution of the feed rod is the critical factor to maintain the stable molten zone and therefore to give optimum growth condition during FZ single crystal growth.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.8
• /
• pp.1771-1776
• /
• 2011

In this paper, as an attempt to improve the preparation conditions of $YBa_2Cu_3Ox$ superconducting bulk samples, the properties of $YBa_2Cu_3Ox$ superconductor depending on the particle size of YBCO powder and $BaPbO_3$ as an additive have been investigated, and a study on the effects of additive to the density, grain alignment, and porosity of samples that affect the critical current of superconductor has been performed. In order to prepare superconductor, $YBa_2Cu_3Ox$ powder synthesized by sol-gel method, showing a size distribution of 0.2~1 ${\mu}m$ was used. The $BaPbO_3$ added to promote grain growth and to decrease porosities and weak links between grain boundaries of $YBa_2Cu_3Ox$ superconductors. In the samples prepared by sol-gel synthesized powder with 10, 20, and 30 wt% conductive $BaPbO_3$ additives, the sample with 20 wt% $BaPbO_3$ obtained the highest critical current of 4.74 A, showing 20 wt% higher critical current than that with solid state synthesized powder.