• Transactions of Materials Processing
• /
• v.13 no.6 s.70
• /
• pp.497-502
• /
• 2004

The shape of cold rolled steel sheets is defined as the degree of flatness, and the flatter, the better. Because undesirable strip shapes of cold rolled steel sheets can affect not only visible problem but also automatic working process in customer's lines, the requirement of the customers is more and more stringent. So we usually used the tension leveler to make high quality of strip flatness. For the improvement of the quality of strip flatness, this report developed three- dimensional FEM (Finite Element Method) simulation model, and analysis about the strain and stress distribution of strip in the tension leveling process. The numerical study can be summarized as follows. (1) If we pass the edge wave material (steepness: $1.0\%$) that the stress-difference between the strip center and the edge is 5.2kgf through tension leveler. the stress-difference is decreased 0.45kgf and the steepness is improved to $0.29\%$. (2) If the Intermesh is increased from 6mm to 7mm, the steepness is improved from $0.294\%$ to $0.268\%$. (3) If the initial steepness is decreased form $1.0\%$ to $0.75\%$, the final steepness is improved from $0.294\%$ to $0.263\%$. We know that more increased intermesh and lower initial steepness make the final steepness improved.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.514-514
• /
• 2017

Floating breakwaters were treated as solid bodies without any perforation in previous studies. In this study, however, a floating breakwater is perforated to allow the partial absorption of the energy produced by incident waves and an air chamber is placed in the upper part to control the breakwater draft. A series of laboratory experiments for a floating breakwater installed with a mooring system are carried out. In general, a mooring system can be classified by the number of mooring points, the shape of the mooring lines, and the degree of line tension. In this study, a four-point mooring is employed since it is relatively easier to analyze the measured results. Furthermore, both the tension-leg and the catenary mooring systems have been adopted to compare the performance of the system. In laboratory experiments, the hydraulic characteristics of a floating breakwater were obtained and analyzed in detail. Also, a hydraulic model test was carried out on variable changes by changing the mooring angle and thickness of perforated wall. A hydraulic model was designed to produce wave energy by generating a vortex with the existing reflection method. Analysis on wave changes was conducted and the flow field around the floating breakwater and draft area, which have elastic behavior, was collected using the PIV system. From the test results the strong vortex was identified in the draft area of the perforated both-sides-type floating breakwater. Also, the wave control performance of the floating breakwater was improved due to the vortex produced as the tension in the mooring line decreased.

• Journal of muscle and joint health
• /
• v.29 no.1
• /
• pp.11-17
• /
• 2022

Purpose: This study aimed to provide objective and basic data for an effective treatment method by examining changes in the mechanical properties of muscles and the degree of tenderness when a combination of stretching exercise and ultrasound therapy is applied to patients with tension headaches. Methods: The participants were classified into two groups based on the intervention received: the therapeutic ultrasound combined with suboccipital stretching (n=15, experimental group) and infrared combined with suboccipital stretching (n=15, control group) groups. The intragroup differences in mechanical muscle properties and modified total tenderness score were compared and analyzed. Results: The comparison and analyses of the changes in muscle tone and stiffness revealed statistically significant intragroup decreases in the upper trapezius and suboccipitalis in the experimental group. Similarly, the comparison and analyses of the changes in muscle stiffness revealed statistically significant intragroup decreases in the upper trapezius in the control group. Conclusion: Therapeutic ultrasound combined with suboccipitalis stretching effectively increased the flexibility of the muscles around the cervical vertebrae and reduced muscle tension and stiffness in tension-type headache patients

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.5
• /
• pp.465-473
• /
• 2009

Three failure theories were studied to evaluate the wood strength variation with grain slope. Maximum stress theory, Tsai-Hill theory and Hankinson formula were presented to hypothesize the failure of wood according to grain slope to loading direction. Red pine and Japanese larch were used as materials to simulate failure strength prediction with grain slope. Calculation of strength results was that the strength of wood drops rapidly between parallel to grain orientation (0 degree) and 15 degree grain orientation. The strength of wood with grain orientation were somewhat different at small grain angles among failure theories, and this tendency was due to tension and compression distinction, and shear accounting in each theories. For the above 45 degree grain orientation, the predicted failure strength of wood with grain variation were very close in each failure theories and were useful in assessing failure strength of wood. The applicable these theories should be considered that the wood has different behavior in tension and compression, and this lead to different strength at small grain angles in each theories. Furthermore, reconsideration is needed to assess the failure strength of wood at small grain angles in Hankinson formula and further studies are necessary to accounting for shear behavior at small grain angles.

• The korean journal of orthodontics
• /
• v.23 no.1 s.40
• /
• pp.89-100
• /
• 1993

The purpose of this study was to evaluate the effect of orthodontic force on periodontal cellular activity by immunoperoxidase stain of epidermal growth factor, one of the tissue hormone. And supplementarily, to investigate of the changes of periodontal structures, periodontium was stained by H-E, Masson's Trichrome, P. A. S. stain after orthodontic force application. The experimental animals were four young adult dogs of average 8 month old. The fixed orthodontic appliance was cemented on mandibular right 4th premolar and 1st molar of each animal as experimental site. Mandibular left 4th premolar area of the same animal was used as control. The appliance consist of two silver crown soldered with 0.030' tube, $0.018\times0.022'$ S.S. sectional arch wire, and 0.009' open coil spring for manifestating of orthodontic force for bodily tooth movement of mandibular 4th premolar toward mesial direction. Experimental group was sacrificed at 1, 2, 3, 5 weeks from beginning of the experiment, and was investigated immunohistochemically and bistochemically by several staining methods. Findings were as follows: 1. The degree of EGF staining in control group was highest in epithelium of periodontium, and osteoclasts, osteoblasts and fibroblasts around the capillary were stained at higher level in periodontium. Generally, control group shows positive distribution of EGF all around the periodontal area. 2. The degree of EGF staining in control and 5 week group were similar, and did not show the significant different level between tension and pressure side. 3. All of 1, 2, 3 week group showed the same staining degree and distribution of EGF, and the tension side was more positive reaction of EGF stain than the pressure side. 4. The features of collagen fiber and periodontal fiber arrangement observed by H-E, Masson's Trichrome and P. A. S. stain revealed that oblique periodontal fibers were strectched in tension side, compressed in pressure side of all experimental group. Some fiber group in pressure side of 5 week group recovered the regular arrangement along the capillaries.

• The Korean Journal of Physiology
• /
• v.14 no.2
• /
• pp.7-16
• /
• 1980

The effects of various inotropic interventions on the shape of the steady state length tension relation and the length-dependent activation process in cardiac muscle were studied. The influence of inotropic interventions upon the action potential was also observed. The range of varying muscle length was from the optimal length$(l_{max})$, where the active tension production is maximal, to 0.85 $l_{max}$. Changes in stimulus frequency or in external bathing Ca concentration constituted the inotropic interventions in this experiment. The papillary muscles were isolated from the rabbit right ventricles and perfused with $HCO-_3\;-buffered$ normal Tyrode solution which was aerated with $3%\;CO_2-97%\;O_2$ mixed gas and kept at $35^{\circ}C$. Resting Passive tension at $l_{max}$ was approximately 30% of the total tension and appeared from the muscle length of 0.90 $l_{max}$. The effect of stimulus frequency on the steady state level of developed tension was: As the stimulus frequency was increased from 0.1 to 0.5 Hz, there was little change in developed tension. As the frequency was increased further, to a value of about 3 Hz, tension increased steeply. Further increase of the frequency to 5 Hz had little additional effect on the developed tension. The length-tension curves for isometric peak tension became more steeper with the degree of potentiation by inotropic interventions. The relative steepness of the normalized length-tension curves where tension production was expressed as a percentage of maximal tension developed at $l_{max}$, varied inversely with the level of inotropic state and these curves were not superimposable one another. Thus at the stimulus frequency of 2 Hz or at the external Ca concentration of 8 mM, the relative decline in the developed tension for a given change in muscle length was considerably less than the decline observed at the frequency of 0.5 Hz or at the concentration of 2 mM Ca. Action potential duration was prolonged significantly as the frequency increased from 0.2 to 2 Hz, and this change in action potential duration was not observable on the changes in muscle length. There was a tendency of the hyperpolarization of membrane potential when the muscle length was shortened from $l_{max}$ to 0.95 $l_{max}$. These results support the hypothesis that there is a length-dependence of the activation process.

• Journal of International Academy of Physical Therapy Research
• /
• v.3 no.2
• /
• pp.475-478
• /
• 2012

The purpose of this study is to identify the level of masseter muscle tension according to the levels of restricted movement and pain in the temporomandibular joint(TMJ), thereby verifying the fact that excessive masseter muscle tension can be a cause for restricted movement and pain in the TMJ. The subjects of this study were 81 men and women in their 20s and 30s, who feel uncomfortable with their masticatory function on the preferred chewing side. The subjects were measured in terms of the range of motion (ROM) and deviation of the TMJ and the degree of pain in the affected region. The ROM and deviation of the TMJ were measured using the Global Posture System(GPS) after instructing each subject to open his/her mouth to the fullest and taking photos of the subject with a digital camera. The tension of the masseter muscle was measured with a Pressure Threshold Meter(PTM). After the measurements, in order to compare the ROM of the TMJ, the subjects were divided into two groups based on the ROM of above 35mm and below 35mm. For the deviation and pain, based on the average of total subjects, the subjects were divided into two groups of above and below average. Thereafter, the levels of masseter muscle tension were compared between each pair of groups. According to the results, when each variable was compared between the respective two groups, in terms of the deviation, the pressure pain threshold(PPT) of the masseter muscle revealed a statistically significant difference(p<.05). However, the ROM and pain showed no statistically significant difference. Consequently, masseter muscle tension may cause restricted movement in the TMJ. In particular, the deviation and tension in the masseter muscle is considered to be a factor that causes deviation in the TMJ.

• Structural Engineering and Mechanics
• /
• v.5 no.5
• /
• pp.507-521
• /
• 1997

The ultimate behavior of a reinforced concrete hyperbolic paraboloid saddle shell under uniformly distributed vertical load is investigated using an inelastic, large displacement finite-element program originally developed at North Carolina State University. Unlike with the author's previous study which shows that the saddle shell possesses a tremendous capacity to redistribute the stresses, introducing tension stiffening in the model the cracks developed are no longer through cracks and formed as primarily bending cracks. Even though with small tension stiffening effect, the behavior of the shell is changed markedly from the one without tension stiffening effect. The load-deflection curves are straight and the slope of the curves is quite steep and remains unchanged with varying the tension stiffening parameters. The failure of the shell took place quite suddenly in a cantilever mode initiated by a formation of yield lines in a direction parallel to the support-to-support diagonal. The higher the tension stiffening parameters the higher is the ultimate load. The present study shows that the ultimate behavior of the shell primarily depends on the concrete tensile characteristics, such as tensile strength (before cracking) and the effective tension stiffening (after cracking). As the concrete characteristics would vary over the life of the shell, a degree of uncertainty is involved in deciding a specified ultimate strength of the saddle shell studied. By the present study, however, the overload factors based on ACI 318-95 are larger than unity for all the cases studied except that the tension stiffening parameter is weak by 3 with and without the large displacement effect, which shows that the Lin-Scordelis saddle shell studied here is at least safe.

• Journal of the Korean Professional Engineers Association
• /
• v.19 no.4
• /
• pp.5-10
• /
• 1986

On SWS 41 Plates jointed by the F11T M 20 high strength bolts the study on stress behavior and safety degree until rupture in static tensile tests were performed. By these results, in case of no clamping force stress concentration was extremed for strain of about 10% higher ratio. Elastic strain occurred to change of test specimens depth by the load and plastic strain occurred to local minute sleep after elastic strain. compared shear stress with tension stress from the fracture load it was showned lower values than the maximum shear stress theory and stress strain energy theory.

• Korean Journal of Occupational Health Nursing
• /
• v.10 no.1
• /
• pp.24-40
• /
• 2001

This study is to observe the effectiveness of the applied model and to present the improvement plan and directions for development for the case management practical model suitable for the actual condition of Korea Labor Welfare Co. and needs of the industrial injury patients. The concrete purpose of this study is: First, observe the difference of stressor experience and experience degree between the experimental group and the comparative group. Second, observe the difference of stress of the experimental group and the comparative group. Third, find out how the stress affects the support degree and satisfaction degree. Fourth, present the improvement plan of case management model, which can promote the psychosocial rehabilitation of the industrial injury patient based on the research results. The outline of the main research results identified in this study is as follows. The stressors the industrial injury patients perceived are health problems, family matters, the problems concerning hospital recuperation (hospital staff and environmental problems), economical problems, problems of coming back to society, problems with companies, problems with Korea labour Welfare Co. and other problems. And the experience of stressor was prominently lower in experimental group than comparative group in the whole problem, health problem, problems with Korea Labour-Welfare Co. and other problems. The stressor experience degree was conspicuously lower in experimental group in the whole problem experience degree, health problem experience degree, problem with Korea Labour Co. experience degree and other problem experience degree. Besides whether or not the case management is applied is having a prominent affect on the primary factor affecting the stressor experience degree, therefore the patients applied with case management has less stressor than the patient who didn't. The difference of degree of tension experienced by the stressor in both groups, the degree of stress, was not conspicuous in statistics so it shows that the application of case management in this research has not affected the degree of tension. The field which had been the most help was emotional support in help level the experimental group perceived through applying case management about industrial accident patients and recuperation, compensation problem, medical treatment problem, family matters has been helpful in this order. The help level of the whole problem was in higher level than the middle value. The stress factor which affects the case management problem settlement is the whole body of stress. The satisfaction level of help through applying case management was highest in emotional support and family matters, recuperation problem, company problem, compensation problem, and medical treatment problem was the next highest. The satisfaction level of the whole problem was higher than the middle value. The stress factor affecting the satisfaction level of help is the whole body of stress. Therefore to reduce the stress level of industrial accident patients and for them to come back to local societies, we need to reinforce the continuance and responsibility of case management model, increase staff, reinforce the role of counsel and medical treatment, intervene in the patient's plan of leaving the hospital, develop social support system and the need to establish After Care Center.