• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.838-841
• /
• 2012

To avoid the damage to circuit and performance degradation by temperature changes, temperature sensing circuit applicable to the IC is proposed in this paper. Temperature sensing is executed by PTAT circuit and power saving mode is activated by internal switch if internal temperature is in high. Also, characteristics of current matching are increased by using current mirror and cascode circuits. From the simulation results, this circuit is operating in action mode if input signal is in low. But it immediately goes into power saving mode if output signal is in high. It shows the output voltage of 1V at $75^{\circ}C$ and 1.75V at $125^{\circ}C$ in action mode and near 0 V(0V~ 7uV) in power saving mode.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.967_968
• /
• 2009

For lighting application, high-power LED nowadays is driven at 350mA and a sensing resistor is used to provide feedback for LED-current regulation. This method adds an IR drop at the output branch, and limits power efficiency as LED current is large and keeps increasing. In this paper, a power efficient LED-current sensing circuit is proposed. The circuit does not use any sensing resistor but extracts LED-current information from the output capacitor of the driver. Controlling the brightness of LEDs requires a driver that provides a constant, regulated current. In one case, the converter may need to step down the input voltage, and, in another, it may need to boost up the output voltage. These situations often arise in applications with wide-ranging ""dirty"" input power sources, such as automotive systems. And, the driver topology must be able to generate a large enough output voltage to forward bias the LEDs. So, to provide this requirements, 13W prototype Buck-Boost Converter is used.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.2100-2101
• /
• 2008

This paper is studied on a protective control system for electrical fire and electrical faults due to over current or electric short circuit faults by using electrical thermal characteristics of PTC (Positive Temperature Coefficient) thermistor and current response characteristics of high sensitive reed switch. The PTC thermistor has characteristic of positive resistivity temperature coefficient according to the temperature variation, which is construction of a regular square and cube demarcation with BaTiO3_Ceramics of positive temperature coefficient. Also PTC thermistor shows the phenomenon which is rapidly increased in the resistivity if the temperature is increased over Curie temperature point, and reed switch, which is used for electrical fault current sensing devices, have a excellent characteristic of response velocity in degree of ${\mu}s{\sim}ms$ that sensing magnetic flux in proportion to dimension of line current. This paper is proposed on a protective control system use PTC thermistor and reed switch for sensor which is protected from electrical fire due to overload faults or electric short circuit faults. Some experimental results of the proposed electric safety control device are confirmed to the validity of the analytical results.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.727-730
• /
• 2005

In this paper, we propose a new current sense amplifier for low-voltage, high-speed SRAM. As a supply voltage is reduced, a sensing delay is increased owing to reduced cell read current. It causes a low-speed operation in SRAM. To overcome this problem, we present a new current sense amplifier which consists of the current-mirror type circuit with feedback structure. For demonstration, a 0.8-V, 256-Kb SRAM incorporating the proposed current sense amplifier has been designed with $0.18-{\mu}m$ CMOS technology. The simulation results show 15.6ns of the sensing delay reduction in comparison with a previous current sense amplifier and 11.5ns of the sensing delay reduction in comparison with a voltage sense amplifier.

• Proceedings of the KIEE Conference
• /
• 2008.10b
• /
• pp.520-521
• /
• 2008

This paper describes a low voltage, low-power CMOS buck DC/DC converter, which has a simple common-gate current sensing circuit. It consumes low power because it includes less transistors than other converters which use operational amplifiers for current sensing. The designed DC-DC converter is fabricated in a 0.18um CMOS technology. A maximum efficiency of 88% has been obtained with the proposed circuit. It has $2V{\sim}3.7V$ input voltage range, $1V{\sim}2.5V$ output voltage range and maximum output current of 1000mA.

• Journal of Magnetics
• /
• v.12 no.1
• /
• pp.35-39
• /
• 2007

A highly sensitive magnetic sensor using the Giant MagnetoImpedance effect has been developed. The sensor performance is studied and estimated. The sensor circuitry consists of a square wave generator (driving source), a sensing element in a form of composite wire of a 25 $\mu$m copper core electrodeposited with a thin layer of soft magnetic material ($Ni_{80}Fe_{20}$), and two amplifier stages for improving the gain, switching mechanism, scaler circuit, an AC power source driving the permeability of the magnetic coating layer of the sensing element into a dynamic state, and a signal pickup LC circuit formed by a pickup coil and an capacitor. Experimental studies on sensor have been carried out to investigate the key parameters in relation to the sensor sensitivity and resolution. The results showed that for high sensitivity and resolution, the frequency and magnitude of the ac driving current through the sensing element each has an optimum value, the resonance frequency of the signal pickup LC circuit should be equal to or twice as the driving frequency on the sensing element, and the anisotropy of the magnetic coating layer of the sensing wire element should be longitudinal.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.2
• /
• pp.133-138
• /
• 2014

This paper proposes a low power-loss averaging current mode control using a resistor and bypass switch. Generally, current sensing method using a resistor has a disadvantage of power loss which degrades the efficiency of the entire systems. On the other hand, proposed measurement technique operating with bypass-switch connected in parallel with sensing resistor can reduce power loss significantly the current sensor. An analog-circuited bypass driver is implemented and used along with an average-circuit mode controller. The bypass switch bypasses the sensing current with a small amount of power loss. In this paper, a 50[W] prototype average current mode boost converter has been implemented for the experimental verification.

• Current Optics and Photonics
• /
• v.7 no.1
• /
• pp.38-46
• /
• 2023

Optical Fourier-domain reflectometry (OFDR) sensors have been widely used to measure distances with high resolution and speed in a noncontact state. In the electroplating process of a printed circuit board, it is critically important to monitor the copper-plating thickness, as small deviations can lead to defects, such as an open or short circuit. In this paper we employ a phase-based OFDR sensor for in situ relative distance sensing of a sample with nanometer-scale resolution, during electroplating. We also develop an optical-path difference (OPD)-regulated sensing probe that can maintain a preset distance from the sample. This function can markedly facilitate practical measurements in two aspects: Optimal distance setting for high signal-to-noise ratio OFDR sensing, and protection of a fragile probe tip via vertical evasion movement. In a sample with a centimeter-scale structure, a conventional OFDR sensor will probably either bump into the sample or practically out of the detection range of the sensing probe. To address this limitation, a novel OPD-regulated OFDR system is designed by combining the OFDR sensing probe and linear piezo motors with feedback-loop control. By using multiple OFDR sensors, it is possible to effectively monitor copper-plating thickness in situ and uniformize it at various positions.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.37 no.2
• /
• pp.60-68
• /
• 2000

This paper describes a design methodology for the CMOS current source which can be implemented in standard memory process. The proposed techniques provide a good characteristic against the power-supply variation by utilizing a self-bias circuit and the reduction of the first-order component of the temperature variation through the new temperature compensation technique and include a new current-sensing start-up circuit enabling a robust operation against the voltage noise generated during the operation of the chip. In addition to the circuit-design technology, techniques where the proposed CMOS current-reference circuit can be applied to the clocking circuits of a very high-speed DRAM are presented. The feasibility of the suggested design methodology for the CMOS current reference is demonstrated by both the analytical method and the circuit simulation.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1154-1164
• /
• 2015

This paper proposes a fully sensorless driver for a permanent magnet synchronous motor (PMSM) integrated with a digital motor controller and an analog pre-driver, including sensing circuits and estimators. In the motor controller, a position estimator estimates the back electromotive force and rotor position using a sliding-mode observer. In the pre-driver, drivers for the power devices are designed with a level shifter and isolation technique. In addition, a current sensing circuit measures a three-phase current. All of these circuits are integrated in a single chip such that the driver achieves control of the speed with high accuracy. Using an IC fabricated using a $0.18{\mu}m$ BCDMOS process, the performance was verified experimentally. The driver showed stable operation in spite of the variation in speed and load, a similar efficiency near 1% compared to a commercial driver, a low speed error of about 0.1%, and therefore good performance for the PMSM drive.