• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.1
• /
• pp.6-13
• /
• 2008

National standard system for calibrating current transformer(CT) up to primary current of 20,000A have been established. The system consists of 20,000 A AC high current source, CT comparator, standard CT, CT under test and CT burden. An AC high current is applied tn the primary windings of both the standard CT and the CT under test, and then the CT comparator measures the ratio error and the phase displacement by comparing the secondary currents of the two transformers. As a validity check for 20,000 A CT calibration system, the comparison with the two national standard institutes(NMIs) has been performed using same CTs. The comparison results of the CTs are consistent with those measured at two NMIs within 0.004 % for ratio error and 0.1 min for phase displacement in the primary current ranges of Ip = 10 - 20,000 A with a secondary current of Is = 5 A.

• Journal of Sensor Science and Technology
• /
• v.1 no.1
• /
• pp.77-83
• /
• 1992

A primary standard of ac current at low frequency is derived from the standard of dc current by ac-dc transfer instrument. A set of 15 thermal current converters(TCCs) have been constructed as the primary current standards from 5 mA to 20 A at the frequency range of 10 Hz to 100 kHz. It is evaluated that the uncertainties for the maintenance and dissemination of ac current standard are less than 52 ppm up to 20 mA and 20 kHz, 60 ppm up to 100 mA and 20 kHz, and rising to 200 ppm at higher currents and frequencies.

• Journal of the Korean housing association
• /
• v.27 no.6
• /
• pp.145-153
• /
• 2016

The purpose of this study is to grasp the effectiveness of evacuation safety design by verifying the appropriateness of the standard of occupant load factor for residential buildings. To this end, the definition and current standard of occupant load factor for residential buildings were analyzed, and the problems of the current standard were clarified by interviewing professionals. In addition, changes in occupant load factor were examined by year based on statistical research, and evaluation on the current standard $18.6m^2/pers.$ was performed. As for evaluation methods, the need of redesigning of evacuation capacity was investigated by using evacuation simulation. As a result of the analysis, the most serious problem was clarification of the applicable standard for residential officetel, where the average occupant load factor was $26.1m^2/pers.$, which was not appropriate. However, as a result of evaluation on evacuation capacity, although there was no difference between statistical research results and the current standard in terms of evacuation capacity, when the standard for business facilities was applied to officetel, evacuation time doubled. Thus, this study suggests that when the current standard is applied to residential officetel, it is necessary to separate between residential use and business use.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.5
• /
• pp.926-932
• /
• 2007

A recently developed methods for on-site calibration of the current transformer (CT) comparator system have been reviewed in the paper. The method utilizes several traveling standards, which consist of the CT, non-reactive standard resistors, wide ratio error CT, and shunt resistors. The traveling CT is used for absolute evaluation of a standard CT belonging to industry. The non-reactive standard resistors and a wide ratio error CT are used for the linearity check of errors in the current comparator. The shunt resistors are used for evaluation of CT burden of industry.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1412-1413
• /
• 2007

20 kA AC high current national standard system has been established with a purpose for support of heavy electrical industry. The system consists of high AC current source, the standard current transformer, current transformer comparator and current transformer burden, and current transformer under test.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.2
• /
• pp.202-206
• /
• 2009

Evaluation system for calibrating Rogowski coiI(RC) up to primary current of 40,000 A have been established. The system consists of 40,000 A AC high current source, current transformer(CT) comparator, standard CT, RC under test, voltage to current convertor(VCC), buffer and CT burden. An AC high current is applied to the primary windings of both the standard CT and the RC under test, and then the CT comparator measures the ratio error and the phase displacement by comparing the secondary current of the standard CT with output current of VCC. For testing of RC, we have evaluated two RCs under test of primary current ranges of 0 A ${\sim}$ 2,000 A and 0 A ${\sim}$ 40,000 A with the accuracy class of 1 %. The extended uncertainty is 0.02 % ${\sim}$ 0.23 % for ratio error and 0.29 min ${\sim}$ 1.93 min for phase displacement in the primary current ranges of 10 ${\sim}$ 40,000 A.

• Korean Journal of Clinical Pharmacy
• /
• v.21 no.3
• /
• pp.193-207
• /
• 2011

Purpose: The purpose of this study is to assess appropriateness of current standard for insurance coverage by Health Insurance Review & Assessment Service (HIRA) on chemotherapy used in the treatment of advanced non-small cell lung cancer (NSCLC), by reviewing a variety of clinical evidences, and thereby, if needed, to propose an updated evidence-based recommendations. Methods: We collected data from HIRA regarding on the insurance standard which includes the scope and conditions for coverage on systemic chemotherapy of NSCLC. We performed a search for clinical databases and examined the most current clinical evidence from clinical literature including various clinical practice guidelines. Based on the collected data the appropriateness of HIRA standard for insurance coverage of chemotherapy of NSCLC was assessed. Results: Collected data demonstrated that HIRA standard did not reflect the most current clinical practice and evidence. Some were inappropriately listed in HIRA formulary and accepted as a chemotherapy being covered by insurance, despite the lack of evidences of clinical efficacy or superiority over other chemotherapeutic agents or regimens. In addition, there seems to be a need for a modification on the standard for insurance coverage of certain newer chemotherapeutic agents based on the current accumulated data showing their clinical efficacy and benefits in the selected group of NSCLC patients. Therefore, we concluded that current HIRA standard for insurance coverage on chemotherapy of NSCLC needs to be revised and we proposed an updated recommendation based on these latest clinical evidences. Conclusion: The standard for insurance coverage of chemotherapy should be continually examined its appropriateness based on the most recent clinical evidences in a timely manner so as to provide the most effective and safe therapy to cancer patients.

• 한국태양에너지학회:학술대회논문집
• /
• 2008.04a
• /
• pp.111-116
• /
• 2008

The objective of this paper was to show the possibility of demand-controlled ventilation (DCV) using the current Korean ventilation standard for multi-purposed facilites. Two attractive DCV approaches; $CO_2$-DCV and RFID-DCV were applied to DCV simulations for a theoretical public assembly space served by a dedicated outdoor air system (DOAS) with enthalpy recovery device. A numerical model for predicting realtime occupant number, ventilation rate, and $CO_2$ concentration under given conditions was developed using a commercial equation solver program. It was found that the current ventilation standard causes unstable ventilation system control in DCV applications, especially under $CO_2$-DCV. It is because the ventilation rate (per person) used in Korea is the sum of the outdoor air required to remove or dilute air contaminants generated by both occupant and building itself, and not a pure function of occupant numbers. Finally, it makes DCV control unstable when ventilation flow is regulated only by the number of occupants. In order for solving this problem, current Korean ventilation standard was modified as a form of ASHRAE Standard 62.1-2007 showing good applicability to various DCV approaches. It was found that this modification enhances applicability of the current ventilation standard to DCV significantly.

• Journal of the Korea Safety Management & Science
• /
• v.13 no.1
• /
• pp.189-193
• /
• 2011

The current standard cost for recycling applied under the Extended Producer Responsibility(EPR) institution, is not coping with continuously increased number of obligatory subject items as well as a variety of variable cost changing factors regarding the recycling treatment cost caused by price fluctuation such as increased material and labor cost entirely across the society; changes in recycling treatment process following the developing technologies; and changes in the required work forces and equipments followed by the trends of automated facilities. Despite such various cost fluctuation factors, the current EPR is not coping with the trends, making the re-calculation process difficult, which causes differences between the real treatment cost for recycling. In this study, the analysis was made on main factors affecting on the related cost and the related price changing index was calculated, by conducting the influence evaluation on the standard cost factors of the current standard cost for recycling. Through theses results, more objective standard will be set for the re-calculation of standard cost for recycling to greatly contribute to setting up the midterm and long-term strategies in the future towards efficient institution.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.3
• /
• pp.71-74
• /
• 2019

In this study, we fabricated two standard and inverted quantum dot light emitting diodes (QLEDs) using $TiO_2$ nanoparticles (NPs) with lower electron mobility than ZnO NPs as inorganic electron transport layer to suppress electron injection into the emitting layer. Current density was much higher for the inverted QLEDs than the standard ones. The inverted QLEDs were brighter, but showed low current efficiency due to the high current density. In addition, as the current density was higher, the driving voltage was higher, and the red shift was confirmed in the emission wavelength spectrum. The low current density in the standard structured devices showed that the possibility that $TiO_2$ NPs could suppress the electron injection in the QLEDs.