• The Journal of Engineering Geology
• /
• v.31 no.3
• /
• pp.343-355
• /
• 2021

Agricultural reservoirs seek human convenience by supplying agricultural water and providing flood damage effects and rest areas at the same time, but preventing them from aging reservoirs and earthquakes is important. The safety of levees is influenced by field material properties such as soil parameter values of the granular materials that make up the levees, but since precision safety diagnosis or general literature values are diverted, the final safety factors are limited to material properties alone. Since safety factors are determined by physical characteristic values and embankment shapes and have a significant impact on safety factors, accurate contemplation is required when examining reinforced cross sections. Therefore, this study analyzed the case of reasonable and economical reinforcement intersections when designing '◯◯reservoir' in Goheung-geun, Jeollanam-do using the GEP-SLOPE program to enable rational economic design of reinforcement intersections through repeated reviews. As a result of reducing and analyzing the first, second, and third seismic reinforcement of the levees, it was confirmed that the safety ratio was secured even with a significantly smaller amount of reinforcement than the first, second, and lower slopes by obtaining design standards of 1.20. In addition, when determining all seismic reinforcement cross-sectional shapes, it was confirmed that the shape that reinforces only the lower side rather than the upper side of the slope and the entire slope was economical with minimized cross-sectional reinforcement.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.11 no.3
• /
• pp.37-46
• /
• 1991

A method is developed for solving the natural frequencies and mode shapes of linearly variable tapered beams. The governing differential equation for the tapered beam is derived. Three kinds of cross sectional shape are considered in differential equation. The Runge-Kutta method and the determinant search method are used to perform the integration of the differential equation and to determine the natural frequencies, respectively. The hinged-hinged, hinged-clamped, damped-clamped and free-damped end constraints are investigated in numerical examples. The lowest four nondimensional natural frequencies are obtained as functions of $d_b/d_a$. ratio. The effects of end constraints and cross sectional shapes on frequencies are analyzed and typical mode shapes are also presented.

• Asian Pacific Journal of Cancer Prevention
• /
• v.17 no.4
• /
• pp.1875-1879
• /
• 2016

Background: Breast cancer is the most common cancer among women worldwide. A very important factor in the timely treatment and prevention of progression is high breast cancer awareness. Rural women are at risk of latte stage breast cancer due to poor education and lack of access to medical facilities. Materials and Methods: This cross-sectional-descriptive study was conducted on 266 women (out of 300) aged over 18 in rural areas of Zabol, Southeastern Iran during July 2015 to October 2015. The data collection tool was a researcher-made questionnaire that measured participant knowledge of breast cancer in four aspects (general awareness, risk factors, mammography, and symptoms). SPSS 22 was used for statistical analysis. Results: Out of 266 participants, age information was available for 261. The age range was between 19 and 62, with a mean of $27{\pm}2.1years$. Most participants (154, 57.9%) had an average overall awareness of breast cancer. In the general awareness dimension, most participants (130, 48.9%) had poor scores. Most (166, 62.4%) also had average awareness about risk factors and many (137, 51.5%) had good awareness about mammography. Most participants did not know that changes in breast shape (232, 88.2%), dimpling of breast skin (192, 72.3%) and nipple discharge (183, 69.6%) are the main symptoms of breast cancer. ANOVA statistical analysis showed a significant relationship between awareness level and participant education and occupation (P<0.05). Conclusions: This study indicated average awareness of participants about breast cancer. Since rural women have lower levels of education, it is recommended that educational courses with contents about breast cancer, its risk factors, and symptoms be held for these women.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.3722-3730
• /
• 2015

The performance improvement of a small centrifugal compressor for waste water treatment has been conducted by the design change of vaneless diffuser and volute casing. Existing two compressors use a common impeller, but the width and length of the vaneless diffuser and the cross-sectional shape of the volute casing are different, respectively. Based on the experiment of the existing two compressors and their CFD results, the design of the vaneless diffuser and the volute casing has been changed. It was found that the strength of the interaction among the volute tongues, the vaneless diffusers and the impellers of two existing/one improved compressors, was affected by the cross-sectional area and inlet radial length of the volute casing including system losses' change. The efficiency of the impeller with one existing design was increased as the decrease of the width of the vaneless diffuser, but losses at the diffuser were accumulated. In conclusion, approximately 2.88%p efficiency increase at the design point of the new compressor with the improved design has been confirmed by CFD analysis results.

• Journal of Surface Science and Engineering
• /
• v.51 no.6
• /
• pp.393-399
• /
• 2018

Formation behavior of aluminum anodic oxide (AAO) films on Al6061 alloy was studied in view of thickness, morphology and defects in the anodic films in 20 vol.% sulfuric acid solution at a constant current density of $40mA/cm^2$, using voltage-time curve, observation of anodized specimen colors and surface and cross-sectional morphologies of anodic films with anodization time. With increasing anodizing time, voltage for film formation increased exponentially after about 12 min and its increasing rate decreased after 25 min, followed by a rapid decrease of the voltage after about 28 min. Surface color of anodized specimen became darker with increasing anodizing time up to about 20 min, while it appeared to be brighter with increasing anodizing time after 20 min. The darkened and brightened surfaces with anodizing time are attributed to an increase in thickness of porous anodic oxide film and a chemical damage of the films due to heat generated by increased resistance of the film, respectively. Cross-sectional observation of AAO films revealed the formation of defects of crack shape at the metal/oxide interface after 15 min which prevents the growth of AAO films. Width and length of the crack-like defect increased with anodizing time up to 25 min of anodizing, and finally the outer part of AAO films was partly dissolved or detached after 30 min of anodizing, resulting in non-uniform surface structures of the AAO films.

• Journal of the Korea Furniture Society
• /
• v.21 no.4
• /
• pp.273-283
• /
• 2010

Structural larger timber have some weak points as like much longer drying time at lower MC(15%), a considerable check developing and the difficulty for the chemicals injection, so it is necessary to develop lighter structural size member for using the new Hanok, heavy timber construction, living necessaries, furniture and industrial goods. The developed skin timber can be a good raw material for those uses. Skin timber is a hollowed timber which be bored out of its considerable cross-sectional area. The intention of this study was the evaluation of compressive capacity of skin timber. Specially, skin timbers which have more than 200mm in sizes were used to analyze the compressive capacity. From the results of this study, the following conclusions have been made: 1. Though considerable inner parts were bored out, both pine skin timber and larch skin timber showed a good compressive capacity to that of non-bored solid timber. 2. According to ASTM, pine skin timber showed various failure types, but Splitting type, Brooming and end rolling type were main failure types for the larch skin timber. 3. Pine skin timber didn't show the significance between cylindrical shape and rectangular shape, but larch skin timber showed the significance between two shapes. Therefore, for the larch skin timber, cylindrical shape and rectangular shape should be used as a column uses and beam uses respectively. 4. Pine skin timber and larch skin timber didn't show the significance on the compressive capacity. There is not much difference of compressive capacity between them, so it can be possible to select on the user convenience.

• The Research Journal of the Costume Culture
• /
• v.8 no.5
• /
• pp.668-680
• /
• 2000

The study presents the general types and individual differences of the shape of the adult women's neck and shoulder in our country. It is based on the average value, the standard deviation, the maximum value, the standard deviation, the maximum value, the minimum value and c.v. measured from the women at the age of 19 through 64. The results of this study are as follows ; 1. The factors by factor analysis are five. The first is the size factors of the neck and shoulder. The second is shape factor of neck. The third is plane view and length factor of the neck. The fourth is the side view factor of the neck and shoulder. The fifth is the shape factor of shoulder. Therefore the shape of the neck and shoulder should be examined in the shape factors as well as in the size factors as well as in the size factors for the designing body-suitable clothes. 2. The factors of the concrete objects are the solid view of neck and shoulder, the cross-sectional view of neck line, side view of neck and shoulder and length of neck. The explainable measuring items for the factors are the difference of the length between lower neck round line and the 4㎝ above neck round line, the length of neck, the angle of inclination between fore neck and back neck, the angle of inclination of the side shoulder, the difference of the height between fore neck point and back neck point, the width of shoulder, the width of chest and the width of back. 3. The concrete objects of the neck and shoulder have five types ; Type Ⅰ is average type, Type Ⅱ is thick short neck and the drooping shoulder type, Type Ⅲ I is slender long neck and lean-back shoulder type, Type Ⅳ is thick and rising shoulder type and Type Ⅴ is slender and drooping shoulder type.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.60 no.1
• /
• pp.67-77
• /
• 2018

The objective of this study is to extract the shape of the slope from the images acquired using UAV and evaluate its suitability and reliability when applied to slope stability analysis. UAV is relatively inexpensive and simple, and it is possible to make terrain survey by generating point clouds. However, the image acquired from UAV can not be directly photographed by the forest canopy due to the influence of trees, resulting in severe distortion of the terrain. In this study, therefore, the effects of forest canopy were verified and the slope stability analysis was performed. Images acquired in winter and summer were used, because summer images are heavily influenced by the forest canopy and winter images are not. As a result of the study, the winter image is suitable for the extraction of slope shape, but severe terrain distortion occurs in the summer image. Therefore, slope stability analysis using slope shape extracted from summer image is impossible, so it should be modified for slope stability analysis. The modified slope did not completely eliminate the distortion of the terrain, but it could express the approximate shape of the slope. As a result of the slope stability analysis, the location and shape of the failure surface are the same, and the error of the safety factor is less than 0.2, which is close to the actual slope.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.4
• /
• pp.421-439
• /
• 2003

Statement of problem : It is difficult to obtain a good titanium casting body using the traditional sprue design because of high melting point of Ti, and the low fluidity and high reactivity of molten Ti. Purpose : A new sprue design for titanium casting bodies needs more trial and error. In order to decrease the number of trial and error, computer simulation(MAGMASOFT, Magmasoft Giessereitechnologie GmbH, Achen, Germany) was used to optimize sprue design in U-shaped implant superstructures. Material and method : Five kinds of sprue were examined for the design of the sprue former for titanium casting: Sprue design A(sprue length 4 mm, rectangular shape, 4 sprues), Sprue design B(sprue length 4 mm. round shape. radius 2 mm, 7 sprues), Sprue design C (sprue length 2 mm, round shape, radius 2 mm, 7 sprues). Sprue design D (sprue length 2 mm, cone shape, large radius 3mm. small radius 2mm, 7 sprues), and Sprue design E( sprue length 2 mm. one unit channel shape). Sprue design F(sprue length 2mm, one unit channel shape) was also examined for the design of the customized sprue former in the Biotan system(Schutz Dental Gmbh, Germany). The casting bodies were taken in Sprue design A, Sprue design D, Sprue design E, and Sprue design F in the Biotan casting system. The numerically predicted defects were compared with the experimental dental castings by the radiographic and sectional view observations. Results : 1. According to the result of computer simulation, turbulence during mold filling was decreased in the sequence of Sprue design F, Sprue design E, Sprue design D, Sprue design C, Sprue design B, and Sprue design A. 2. The calculated solidification time contours indicate that hot spot was moved from the casting body to the sprue button in the sequence of Sprue design A, Sprue design B, Sprue design C, Sprue design D, and Sprue design E. The filling pattern of Sprue design F was similar to that of Sprue design E. 3 The predicted filling pattern shows that less turbulence was found in the customized sprue former than in the standard sprue former. 4. According to the results of the radiographic and cross sectional observations, casting defects less than 1mm were found at the center of a casting body with Sprue design E and Sprue design F. However, larger casting defects of 4mm were found in a casting with Sprue design A. 5. The predicted casting porosity was similar to that of the real casting. Conclusion : One unit channel-type and customized sprue former can be recommended. Further research and developement of various sprue designs using computer simulation in necessary to optimize casting design, in order to reduce the formation of casting defects in implant titanuim super-structures.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.5
• /
• pp.107-114
• /
• 2019

In many military aircraft, s-shaped diffusers are used to prevent the fan blades of the turbofan engine from being exposed to the outside. The inlet configurations of the air intakes for military aircraft vary, such as the rectangular intake of the F-22, the crescent-like intake of the F-16, elliptical intake of the MQ-25. In this study, the aerodynamic performance of s-shaped diffusers with various inlet configurations was evaluated using numerical analysis. In addition, the configuration of the middle section of an s-shape duct was changed to the crescent shape, and the effects on its aerodynamic performance were investigated. As a result, there was a slight difference in total pressure recovery according to various inlet configurations with ellipse-shaped middle sections. Also, the total pressure distortion was the lowest in the rectangular inlet shape. When the configuration of the middle section was changed from an ellipse to a crescent shape, the total pressure recovery remained at a high level, except for the ellipse-shaped inlet configuration. In terms of total pressure distortion, the duct with the crescent-shaped middle section showed a significantly more uniform pressure distribution than that with the ellipse-shaped middle section.