• Journal of the Korean Society of Food Science and Nutrition
• /
• v.37 no.11
• /
• pp.1465-1471
• /
• 2008

This study was carried out to make water-soluble tocopherol emulsion which can be applicable directly in water. The molecular weight of tocopherol was 340 to 360 and tocopherol emulsion model was decided as O/O/W/W type. In correlation between stability of emulsion and surface tension, the stability in surface tension of emulsion was from 40 to 46 dyne/cm. In the case of lower than 40 dyne/cm of surface tension, the stability of the emulsion was lower. Lipophilic surfactants, especially for a polyglycerine polyricinoleate in 20%, 30% and 40% tocopherol emulsion, was the most effective in emulsion stability. A higher stability of the emulsion among hydrophilic surfactants in the tocopherol emulsion was obtained in the following order; polyglycerine monostearate> polyglycerine monooleate> polyoxyethylene (20) sorbitan monooleate$\geq$ polyoxyethylene (20) sorbitan monolaurate.

• Korean Chemical Engineering Research
• /
• v.50 no.2
• /
• pp.282-291
• /
• 2012

The PGLE and PGLE3 nonionic surfactants were synthesized from the reaction between glycidol and lauryl acid and their structures were confirmed by $^1H$ and $^{13}C$ NMR analysis. The CMCs of PGLE and PGLE3 surfactants were found to be $3.59{\times}10^{-2}$ mol/L and $8.80{\times}10^{-2}$ mol/L respectively and the surface tensions at their CMC conditions were 26.09 mN/m and 28.68 mN/m respectively. Dynamic surface tension measurement has shown that the adsorption rate of surfactant molecules at the interface between air and surfactant solution was found to be relatively fast in both surfactant systems, presumably due to high mobility of surfactant molecules. The contact angles of PGLE and PGLE3 nonionic surfactants were $25.5^{\circ}$ and $9.5^{\circ}$ respectively. Dynamic interfacial tension measurement showed that both surfactant systems reached equilibrium in 20 minutes and the interfacial tensions at equilibrium condition in both systems were 0.42 mN/m and 0.53 mN/m respectively. The PGLE surfactant system has indicated higher foam stability than the PGLE3 surfactant system, which is consistent with surface tension measurement. The phase behavior experiments performed at $25{\sim}60^{\circ}C$ in systems containing nonionic surfactant, water, n-hydrocarbon oil and cosurfactant showed a lower phase or oil in water microemulsion in equilibrium with excess oil phase at all conditions investigated during this study.

• KSBB Journal
• /
• v.14 no.6
• /
• pp.737-741
• /
• 1999

Phenanthrene degrading bacteria were isolated from the petroleum contaminated soil near an oil tank. Four of 15 strains decreased surface tension of culture broth of phenanthrene-containing minimal media. H6, one of the isolated bacteria decreased surface tension of culture broth below 33 dyne/cm during growth on glucose. H6 was identified as Bacillus subtilis and biosurfactant produced by H6 was lipopeptide. The biosurfactant was produced at 0.13 g/L in the mineral medium containing 2% glucose. Critical micelle concentration(CMC) of the biosurfactant was 52 mg/L. Foaming power was similar to Tween 80 and dispersing power was superior to Tween 80m SDS and Brij30. High thermal stability and emulsion index were also observed.

• Applied Chemistry for Engineering
• /
• v.19 no.5
• /
• pp.484-490
• /
• 2008

Electrospun of PVP (polyvinylpyrrolidone) ultra fine fibers were fabricated using various solvents including methanol, ethanol, 2-propanol, butanol, acetone, methylene chloride, and DMF, which possess different properties such as boiling point, dielectric constant, and dipole moment. Electrospun PVP fiber was influenced by viscosity, conductivity, and surface tension of spinning solution. Therefore, the electrospun PVP fiber was successfully prepared under critical conditions of viscosity > $0.114kg/m{\cdot}s$, conductivity > 1.02 mS/m, surface tension < 30.0 mN/m. In case of an ethanol solvent system, average diameter of PVP fiber increased from 1701 nm to 5454 nm as increased the applied voltage from 10 kV to 20 kV.

• Journal of Microbiology and Biotechnology
• /
• v.23 no.3
• /
• pp.390-396
• /
• 2013

Biosurfactants have versatile properties and potential industrial applications. A new producer, B. subtilis TU2, was isolated from the underground oil-extraction wastewater of Shengli Oilfield, China. Preliminary flask culture showed that the titer of biosurfactant obtained from the broth of TU2 was ~1.5 g/l at 48 h (718 mg/l after purification), with a reduced surface tension of 32.5 mN/m. The critical micelle concentration was measured as 50 mg/l and the surface tension maintained stability in solution with 50 g/l NaCl and 16 g/l $CaCl_2$ after 5 days of incubation at $70^{\circ}C$. FT-IR spectra exhibited the structure information of both glycolipid and lipopeptide. MALDI-TOF-MS analyses confirmed that the biosurfactant produced by B. subtilis TU2 was a blend of glycolipid and lipopeptide, including rhamnolipid, surfactin, and fengycin. The blended biosurfactant showed 86% of oil-washing efficiency and fine emulsification activity on crude oil, suggesting its potential application in enhanced oil recovery.

• Journal of the Korean Applied Science and Technology
• /
• v.9 no.1
• /
• pp.1-6
• /
• 1992

New five N-acyl-N-methyl taurate and their sodium salts were synthesized by acylating sodium N-methyl taurate in water in the presense of inorganic alkali as a catalyst. Wherein acyl group is a straight-chain radical of 10 to 18 carbon atoms. These compounds were identified by infrared spectroscopy. Surface activities of these sodium N-acyl-N-methyl taurate including surface tension, Ross-Miles foaming powers, foam stabilities, emulsifying powers and detergency were measured respectively. Also critical micelle concentration(cmc) were evaluated. Consequently these anionic surfactants with long chain acyl amine showed good emulsifying power of O/W type and had a good detergence.

• Nuclear Engineering and Technology
• /
• v.38 no.8
• /
• pp.753-762
• /
• 2006

In this paper, works related to enhancement of the CHF are reviewed in terms of fundamental mechanisms and practical applications. Studies on CHF enhancement in forced convection are divided into two categories, CHF enhancement of internal flow in tubes and enhancement of CHF in the nuclear fuel bundle. Methods of enhancing the CHF of internal flows in tubes include enhancement of the swirl flow using twisted tapes, a helical coil, and a grooved surface; promotion of flow mixing using a hypervapotron; altering the characteristics of the heated surface using porous coatings and nano-fluids; and changing the surface tension of the fluid using additives such as surfactants. In the fuel bundle, mixing vanes or wire wrapped rods can be employed to enhance the CHF by changing the flow distributions. These methods can be applied to practical heat exchange systems such as nuclear reactors, fossil boilers, fusion reactors, etc.

• Electrical & Electronic Materials
• /
• v.8 no.3
• /
• pp.316-323
• /
• 1995

A vital step in magnetic tape manufacturing is the surface modification of polymer substrate prior to ink application. A critical element for good adhesion of magnetic ink on polymeric substrate is the ability to join ink in cost-effective manner. Corona discharging is one of the effective methods of modifying polymer surface to improve adhesion while maintaining the desirable properties of the film itself. Surface treatment by corona which is exposure of film surface to electron or ion bombardment, rather than mere exposure to active species, like atomic oxygen or ozone, can enhance adhesion by removing contaminant, electret, roughening surface, and/or introducing reactive chemical groups. Reactive neutrals, ions, electron and photons generated during the corona treatment interact simultaneously with polymers to alter surface chemical composition, wettability, and thus film adhesion. However, it is highly recommended that extensive chains scission be avoided because it can lead to side-effect by forming sticky matter, resulting in dropouts. This paper reviews principles of surface preparation of polymer substrate by corona discharging. In addition, the experimental section provides a description of parameter optimization on corona discharging treatment and its side-effect. Experimental results are discussed in terms of surface wetting as determined by contact angle measurements.

• Structural Engineering and Mechanics
• /
• v.32 no.4
• /
• pp.477-488
• /
• 2009

A slip critical joint has various values to adopt the proper slip coefficient in various conditions of faying surfaces in the following codes: AISC, AIJ and Eurocode 3. However, the Korean Building Code still regulates the unique slip coefficient, 0.45, regardless of the diverse faying conditions. In this study, the slip resistance test, including five kinds of surface treatments were conducted to obtain the proper slip coefficients available to steel plate KS SM490A. The faying surfaces were comprised of a clean mill, rust, red lead paint, zinc primer, and shot blast treatment. The candidates for high strength bolts were torque-shear bolts, torque-shear bolts with zinc coating, and ASTM A490 bolts. Based on the test results, the specimens with a shot blasted surface and rusted surface exhibited $k_s$, 0.61, and 0.5, respectively. It is recommended that the specimens with zinc primer exhibit $k_s{\geq}0.40$. The clean mill treated surface had prominently lower values, 0.27. For red lead painted treatment, the thickness of the coating affects the determinant of slip coefficient, so it is necessary to establish a minimum $k_s$ of 0.2, with a coating thickness of 65 ${\mu}m$. During 1,000 hours of relaxation, the uncoated surfaces exhibited the loss of clamping force behind 3%, while the coated surfaces within a certain limited thickness exhibited the loss of clamping within a range of 4.71% and 8.37%.

• Journal of the Korean Applied Science and Technology
• /
• v.15 no.2
• /
• pp.77-81
• /
• 1998

Surface active properties of these aqueous Gemini surfactant solutions including surface tension, critical micelle concentration(cmc), foaming power, foam stability, emulsifying power and Krafft point were measured at given conditions. They showed excellent properties, being compared with conventional single-chain surfactants such as sodium dodecyl sulfonate(SDS). Their surface tensions in the aqueous solutions were decreased to $30{\sim}38$ mN/m, which is lower than 39 mN/m of SDS, and their cmc values evaluated by surface tension method were $2.8{\times}10^{-5}{\sim}3.3{\times}10^{-4}$ mol/L. These values were also much lower than that of SDS, $9.8{\times}10^{-3}$ mol/L. The foaming power and foam stability, especially decyl and dodecyl compounds, were good and the emulsifying power in benzene or soybean oil was also excellent. All of the synthesized Gemini surfactants possessed good water solubility and their Krafft points were all below $0^{\circ}C$. As results, DDED and DDOD, Gemini surfactants which were synthesized are expected to be applied as foamers, emulsifiers and so on.