• Journal of the Korean Society of Safety
• /
• v.20 no.2 s.70
• /
• pp.32-37
• /
• 2005

The purpose of this study is for the sensitivity study f9r a Steam Generator Tube Rupture (SGTR) of the System-integrated Modular Advanced ReacTor for a Pilot (SMART-P) plant. The thermal hydraulic analysis of a SGIR for the Limiting Conditions for Operation (LCO) is performed using TASS/SMR code. The TASS/SMR code can calculate the core power, pressure, flow, temperature and other values of the primary and secondary system for the various initiating conditions. The major concern of this sensitivity study is not the minimum Critical Heat Flux Ratio(CHFR) but the maximum leakage amount from the primary to secondary sides at the steam generator. Therefore the break area causing the maximum accumulated break flow is researched for this reason. In the case of a SGIR for the SMART-p, the total integrated break flow is 11,740kg in the worst case scenario, the minimum CHFR is maintained at Over 1.3 and the hottest fuel rod temperature is below 606"I during the transient. It means that the integrity of the fuel rod is guaranteed. The reactor coolant system and the secondary system pressures are maintained below 18.7MPa, which is system design pressure.

• Health Policy and Management
• /
• v.5 no.2
• /
• pp.155-172
• /
• 1995

This study is an empirical analysis on the equity in the delivery of heatlh care under the Korean Medical Insurance Corporation System. The purposes of this study are to find out effects of income on the health care utiliztion and measure the income-related inequity in the distribution of health care. This study was carried out based on the fact that the health insurance program has been organized to achieve the equity objective, "equal treatment for equal needs". Of 41, 828 insured persons who had been diagnosed in the 1993 Health Screening Test and utilifzation data from 1, January 1993 through 31, December 1993 were derived from the Benefit Managment File. Inequity was measured by means of I) share approach, ii) standardization concentration curve approach, iii) inequity index, iv) test for inequity. The major findings were as follows : 1. The expenditure shares of the top two quintile groups exceeded their morbidity shares, whereas the opposite was true of the bottom three quintile groups, Which showed a positive HI$_{LG}$ inequity index, suggesting the presence of some inequity favoring the rich group. 2. Compared with other residential areas, the rural area showed the highest positive HI$_{LG}$ irrespective of need indicatior applied. 3. Standardized expenditure concentration indices adjusted by age, gender and need structure were also found to be positive, and therefore still indicated that there has been inequity favoring the rich after the standardization. 4. The Loglikelihood Ratio (LR) test for the statistical significance of income-related inequity of medical care utilization was carried out using the logistic regression model. The resulting loglikelihood ratio test statistic value was 176, which did exceed the 0.5 percent critical value of the chi-square distribution with 28 degrees of freedom, which is 50.993. Therefore, the null hypothesis of no income-related inequity of medical care utilization was rejected at the 99.5 percent confidence level. 5. The Regression based F-test has been carried out for analyzing the income-related inequity of medical expenditure in terms of age, gender, morbidity indicators as explanary variables. The hypothesis of the absence of income-relate inequity was rejected for all need indicators at the 95% confidence level.nce level.

• Progress in Superconductivity
• /
• v.5 no.1
• /
• pp.75-79
• /
• 2003

YBCO films were deposited with various thicknesses from 100nm to 1.6$\mu\textrm{m}$ on single crystal $SrTiO_3$ substrates by pulsed laser deposition (PLD). The effects of different deposition conditions, especially different deposition rates by means of changing the pulsed laser frequency up to 200Hz, on the J$_{c}$ value were studied. For YBCO film with the thickness of 200nm, the $J_{c}$ value of $2.1MA/\textrm{cm}^2$ has been achieved under the high deposition rate of 3.2nm/s (190nm/min). The $J_{c}$ can be maintained greater than $1M/\textrm{cm}^2$ with the thickness less than 1$\mu\textrm{m}$. The X-ray analysis was used to examine the texture, crystallization and surface quality. The SEM was employed to analyze the surface of YBCO, and it was shown the surface of YBCO film became rougher with increasing the thickness. There were many large singular outgrowths and networks of outgrowths on the surface of YBCO films which lowered the density of thick YBCO film. The outgrowth network was probably the a-axis YBCO corresponding to XRD $\theta$-2$\theta$scan and $\chi$-scan which were used to characterize a-axis orientation of YBCO film. The reason for J$_{c}$ declining with increasing the thickness was studied and discussed.sed.

• Journal of computational fluids engineering
• /
• v.3 no.1
• /
• pp.82-88
• /
• 1998

As a par of a project related to the development of the design algorithm of a compact heat exchanger for the application of the electronic home appliances, the effect of the discreteness of the airflow boundary generated on the cooling fin surface on the heat transfer and pressure drop characteristics of the heat exchanger was studied numerically. In general, there are two critical design parameters seriously considered in the design of the heat exchanger; heat transfer rate(Q) and pressure drop coefficient(C/sub p/). Even though the higher heat transfer rate with lower pressure drop characteristics is required in a design of the heat exchanger, it is not an easy job to satisfy both conditions at the same time because these two parameters are phenomenally inversely proportional. To control the boundary layer thickness and its length along the streamline, the surface of the flat fin was modified to accelerate the heat transfer rate on the fin surface. To understand the effect of the discreted fin size(S/sub w/) and its location(S/sub h/) on the performance of the heat exchanger in the airflow field, the flat fin was modified as shown in Fig. 1. From this study, it was found that the smaller and more number of slits on the fin surface showed the higher energy diffusion rate. It means that the discreteness of the boundary layer is quite important on the heat transfer rate of the heat exchanger. On the other hand, if the fin surface configuration is very complex than needed, higher static pressure drop occurs than required in a system and it may be a reason of the induced aerodynamic noise in the heat exchanger.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.774-779
• /
• 2007

The crash energy absorbers used in the trains normally are classified into two types. The first is the structure type, which mainly used in not only the primary structure of train but also the crash energy absorbers at the critical accidents. The second is the module type, which just absorbs the crash energy independently and attached onto the structures of the trains. The expansion tube is widely used as the module type of the crash energy absorbers, especially in the trains that have a heavy mass. Since the crash energy is absorbed by means of expanding the tube in the radial direction, the features of the expansion tube have the uniform load during the compression. As the uniform load remains in sudden impact, the expansion tube is effective to decrease acceleration of passengers when the train accident occur. The buckling instability of the expansion tubes is affected by the boundary conditions, thickness and length of tube. In this study, the effects of the length and thickness of the expansion tubes under the arbitrary load on the buckling are studied using the ABAQUS/standard and ABAQUS/explicit, a commercial finite element analysis program, and then presents the guideline to design the expansion tubes. The analysis processes to compute the buckling load consist of the linear buckling analysis and the nonlinear post-buckling analysis. To analysis the nonlinear post-buckling analysis, the geometry imperfections are introduced by applying the linear buckling modes to nonlinear post-buckling analysis.

• Archives of Plastic Surgery
• /
• v.35 no.5
• /
• pp.569-573
• /
• 2008

Purpose: Surgical excision of the subcutaneous tissues, with or without skin excision in the axillary hair-bearing area, has been the treatment of choice in treating osmidrosis for several decades. However, long periods of postoperative immobilization of a shoulder joint, partial necrosis of skin flaps or the possibility of hematoma and scars have occurred frequently. So we used $XPS^{(R)}$ microresector(Shaver) in procedure which requires removal of soft tissue for comparing results between surgical excision and the laters. Methods: From January 2007 to February 2008, a total of 20 patients(8 male and 12 female) underwent $XPS^{(R)}$ microresector(Shaver) assisted aspiration for treating osmidrosis. The mean age of the subjects was 21.9, and we tried to analyze some advantages of $XPS^{(R)}$ microresector(Shaver). Results: The average operation time was 61.6 minutes. This results can show that the patients who received $XPS^{(R)}$ microresector(Shaver) assisted aspiration can accomplish better outcomes than any other procedures in terms of operation time at least. Moreover, no significant postoperative complications occurred in our studies. Subjects have been followed up from 2 months to 1 year and among these patients, no one suffered from critical complications. Conclusion: In brief, $XPS^{(R)}$ microresector(Shaver) is able to shorten the time of operation and simplify the procedures relatively and this device has more superiorities in wound healing by maintaining of vascularized dermal skin flaps. It means that $XPS^{(R)}$ microresector (Shaver) can prevent flap necrosis, axillary hair loss and minimalize scarring and bleeding. Thus, we expect that these advantages can lead to better patient's comfort and self-confidence than several previous procedures.

• Journal of Korea Society of Industrial Information Systems
• /
• v.25 no.3
• /
• pp.53-59
• /
• 2020

This paper proposes color segmentation for detecting missing persons in a smart lighting system using radar and camera sensors. Recently, smart lighting systems built-in radar and cameras have been efficient in saving energy and searching for missing persons, simultaneously. In smart lighting systems, radar detects moving objects and then the lights turn on and camera records. The video recorded is useful to find out missing persons. The color of their clothes worn in missing persons is one of critical hints to look for missing persons. Therefore, color segmentation is an effective means for detecting the color of their clothes. In this paper, during the color segmentation step, the ROI(Region of interest) setting based on the size of an object is applied and the background is reduced. According to experimental results, the color segmentation has good accuracy of more than 97%.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.44 no.3
• /
• pp.385-399
• /
• 2020

Corporate social responsibility is a consistently discussed theme in many industries. Most corporations engage in CSR activities and now inform consumers in detail on what they have been doing for society. It has become a critical tool of consumer communication; however, little is known regarding the role of information transparency in the context of the fashion industry. This study discusses information transparency of fashion corporations which means revealing information regarding cost and garment making processes. The research proved that the higher consumers perceive a fashion brand's CSR performance (CSP), the more they think the provided CSR information is substantial; consequently, there is a favorable evaluation of the brand. The result provides insight regarding the relationship between CSP perception, perceived information substantiality, and brand evaluation. There was a significant partial mediation effect of perceived information substantiality. Moreover, the moderated mediation effect of information transparency appeared significant on the impact of CSP perception for brand evaluation via CSR information substantiality. The process model 7 was used as an analytical tool. The results of this study implies the importance of information transparency in the fashion industry context in the digital era.

• Cartoon and Animation Studies
• /
• s.27
• /
• pp.127-151
• /
• 2012

Created by Tomoko Ninomiya, was serialized in Japan from July 2001 to November 2009 and collected in 23 volumes. It has become a cultural syndrome after it was transferred to other media. Giving an attention to this cultural syndrome, this study aims to analyze narrative structure by means of semiotics. This study tries to use 'modele actantiel' and 'carre semiotique' of Greimas in order to clarify not only the meaning structure but also the course of narrative revealed in . The meaning structure of shows a unique relationship of genius and training. Although Nodame, a main character of this Japanese manga, is a straggler in music school because she does not show any passion for learning, she is depicted as a music genius. An education method called as apprenticeship is represented as the mechanism to bring out misfits in music. Dealing with her long journey to be a professional musician, this manga suggests how Nodame can be developed from as a misfit to as a professional pianist through introducing diverse education methods. Revealing critical perspective on music education in real world, gives a chance to rethink the relationship between genius and education in music.

• Archives of design research
• /
• v.20
• /
• pp.41-48
• /
• 1997

We easily witness that environmental issue is very critical point to affluence upon a restructuring the value system of human being. Therefore it is obvious that this issue affluence upon the field of design as well. The most important feature of environmental issue is 'wholeness' in itself. It means that we have to approach and to solve it as a whole. Also, design is to be done at the same way. The creative professionalism of design could provide a clue to solve the problem, but designer are tend to seek a solution in a just partial way such as recycling and packaging. But those attitude may cause more problems and spread it futhermore. Therefore this study is analysis some recognitive turning factors in order to solve the problems as a whole, and to suggest a appropriate methods according to such a view point. Even internal retrospect in design itself or external demand from the other, If we look away this issue, the real purpose of design, contributing for society, should be diluted by ourselves.