• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.955-956
• /
• 2006

Fe-doped $TiO_2$ nanopowders were prepared by mechanical alloying (MA) varying Fe contents up to 8.0 wt.%. The UV-vis absorption showed that the UV absorption for the Fe-doped powder shifted to a longer wavelength (red shift). The absorption threshold depends on the concentration of nano-size Fe dopant. As the Fe concentration increased up to 4 wt.%, the UV-vis absorption and the magnetization were increased. The benefical effect of Fe doping for photocatalysis and ferromagnetism had the critical dopant concentration of 4 wt.%. Based on the UV absorption and magnetization, the dopant level is localized to the valence band of $TiO_2$.

• KSBB Journal
• /
• 제10권4호
• /
• pp.386-392
• /
• 1995

The high viscous ${\gamma}$-polyglutamic acid(${\gamma}$-PGA) from alkalophilic Alcaligenes sp. was purified and its solution property was investigated. The intrinsic viscosities for Na+ form and H+ form of ${\gamma}$-PGA were 31.1 and 0.38d$\ell$/g, respectively. The viscosity of H+-PGA was not influenced by pH or salts while that of Na+-PGA was influenced. The intrinsic viscosity of Na+-PGA solution decreased remarkably at the alkaline or acidic pH and showed the sharp decrease when salts were added. ${\gamma}$-PGA exhibited the property of the polyelectrolyte showing the .sharp decrease of intrinsic viscosity by the addition of NaCl, and intrinsic viscosity of dilute solution with the low concentration of NaCl was exponentially dependent on temperature and its temperature dependency increased with increasing NaCl concentration. The chain stiffness, coil overlap parameter and critical concentration of Na+-PGA were 0.08, 5.25 and 0.07g/d$\ell$, respectively.

• 통합자연과학논문집
• /
• 제7권2호
• /
• pp.120-123
• /
• 2014

When a hydrophobic and hydrophilic environments of bis(2,2'-bipyridyl) copper(II) ($Cu(bpy)_2{^{2+}}$) are produced in the presence of anionic surfactant sodium dodecyl sulfate (SDS), cyclic voltammetry is used to investigate the microscopic environments which occurs at the glassy carbon electrode. In order to see the relation between ${\Delta}E_p$ and a critical micelle concentration (CMC), ${\Delta}E_p$ vs. -Log[SDS] for the redox couples are plotted. The concentration at the intersection of two lines is 2.57 mM SDS, and this concentration can be determined as the CMC (relative error: below 0.03%; 2.63 mM SDS by surface tensiometry).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.140-141
• /
• 2006

Background doping concentration (BDC) is proven to be a critical factor to affect the high current behavior of the extended drain NMOSFET (EDNMOS) devices. The EDNMOS device with low BDC suffers from strong snapback in the high current region, which results in poor electrostatic discharge (ESD) protection performance and high latchup risk. However, the strong snapback can be avoided in the EDNMOS device with high BDC. This implies that both the good ESD protection performance and the latchup immunity can be realized in terms of the EDNMOS by properly controlling its BDC.

• 설비공학논문집
• /
• 제15권11호
• /
• pp.964-969
• /
• 2003

The objective of this study is to investigate the effect of surfactant on the onset of Marangoni convection adapting a non-linear surface equation of state. The surface tension gradient with respect to the absorbate concentration, ${\gamma}$, is linearly related to the surface concentration of a surfactant with a coeffcient $x_{A}$. The numerical results show that the role of the initial surfactant concentration to Marangoni instability changes from the stabilizer to the destabilizer depending on the change of the sign of $x_{A}$ from negative to positive. It is concluded that for $x_{A}$>0 there is a critical modified Marangoni number of surfactant $M_{Ac}$ $^{*}$ above which liquid layer is always unstable against long wave disturbances.rbances.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.982-987
• /
• 2006

The fluid mechanics and heat transfer of surfactant turbulent pipe flows are characterized with particular emphasis on the effects of surfactant concentration and solution temperature on drag reduction and heat transfer reduction. The test fluids are the surfactant solutions of DR-IW616 supplied by Akzo Nobel Chemical in concentration of $100{\sim}3000ppm$. The solution temperatures studied are $5^{\circ}C$ to $50^{\circ}C$. The critical values of surfactant concentration and solution temperature are clearly identified for drag reduction phenomena.

• 대한의생명과학회지
• /
• 제29권2호
• /
• pp.88-94
• /
• 2023

In oriental medicine, the fruit of Actinidia polygama has long been used to alleviate the symptoms of gout, arthritis, and inflammation. In this study, it was to designed to analyze the antibacterial activity of A. polygama ethanol extract (APEE) against Streptococcus mutans, one of the major strains for dental caries, and Porphyromonas gingivalis, one of the critical strains for periodontal disease. The antibacterial activity of APEE was analyzed by disk diffusion, minimum inhibitory concentration (MIC), and minimum bactericidal concentration (MBC) assays. In addition, it was also analyzed the inhibitory effect of APEE on bacterial growth and biofilm formation against both oral pathogens. APEE exhibited its antibacterial effect through the inhibited bacterial diffusion as well as low concentration of MIC and MBC. In addition, APEE significantly inhibited not only bacterial growth but also biofilm formation in a dose-dependent manner. Consequently, APEE showed potent antibacterial activity against both S. mutans and P. gingivalis, which indicates that APEE might be used as a potential antibacterial material for the improvement of oral healthcare.

• Journal of Biosystems Engineering
• /
• 제37권4호
• /
• pp.233-244
• /
• 2012

Purpose: The kinetic evaluation was performed for swine manure (SM) degradation and biogas generation. Methods: The SM was anaerobically digested using batch digesters at feed to inoculum ratio (F/I) of 1.0 under mesophilic conditions ($36.5^{\circ}C$). The specific gas yield was expressed in terms of gram total chemical oxygen demand (mL/g TCOD added) and gram volatile solids added (mL/g VS added) and their effectiveness was discussed. The biogas and methane production were predicted using first order kinetic model and the modified Gompertz model. The critical hydraulic retention time for biomass washout was determined using Chen and Hashimoto model. Results: The biogas and methane yield from SM was 346 and 274 mL/ TCOD added, respectively after 100 days of digestion. The average methane content in the biogas produced from SM was 79% and $H_2S$ concentration was in the range of 3000-4108 ppm. It took around 32-47 days for 80-90% of biogas recovery and the TCOD removal from SM was calculated to be 85%. When the specific biogas and methane yield from SM (with very high TVFA concentration) was expressed in terms of oven dried volatile solids (VS) basis, the gas yield was found to be over estimated. The difference in the measured and predicted gas yield was in the range of 1.2-1.5% when using first order kinetic model and 0.1% when using modified Gompertz model. The effective time for biogas production ($T_{Ef}$) from SM was calculated to be in the range of 30-45 days and the critical hydraulic retention time ($HRT_{Critical}$) for biomass wash out was found to be 9.5 days. Conclusions: The modified Gompertz model could be better in predicting biogas and methane production from SM. The HRT greater than 10 days is recommended for continuous digesters using SM as feedstock.

• 터널과지하공간
• /
• 제8권2호
• /
• pp.107-117
• /
• 1998

In the case of a fire disaster in a uni-directional road tunnel, it is important to determine the critical ventilation velocity to prevent the backflow travelling toward the tunnel exit where vehicles are stopped. The critical ventilation velocity is horizontal velocity to prevent hot smoke from moving toward the tunnel exit. According to Froude modelling, the model tunnel whcih was 300mm in diameter and 21 m in length was made of acryl tubes. Inner section of acryl tubes was clothed with polycarbonate. 1/20 scaled model vehicles were installed to simulate the situation that vehicles are stopped in the tunnel exit. Methanol in a pool type burner was burned in the middle of tunnel to simulate a fire hazard. In this study, the basis of determining the critical ventilation velocity is the ventilation flow rate that is able to maintain the allowable CO concentration in the tunnel section. We assumed that the allowable CO concentration was backflow dispersion index. Futhermore, We intended to find out CO distribution and temperature distribution according as we changed ventilation velocity. The results of this study were that no backflow happened when ventilation velocity was 0.52 m/s in the case of 5.75 kW. If we adapt these results of a fire disaster releasing 10MW heat capacity in real tunnel which is 400m in length, no backflow happens when ventilation velocity is 2.31m/s. After we figured out dimensionless heat release rate and dimensionless ventilation velocity of model test and those of real test to verify experimental correctness, we tried to find out correlation between experimental results of model tunnel and those of real tunnel.

• Smart Structures and Systems
• /
• 제15권1호
• /
• pp.99-117
• /
• 2015

The Stonecutters Bridge (SCB) in Hong Kong is the third-longest cable-stayed bridge in the world with a main span stretching 1,018 m between two 298 m high single-leg tapering composite towers. A Wind and Structural Health Monitoring System (WASHMS) is being implemented on SCB by the Highways Department of The Hong Kong SAR Government, and the SCB-WASHMS is composed of more than 1,300 sensors in 15 types. In order to establish a linkage between structural health monitoring and maintenance management, a Structural Health Rating System (SHRS) with relevant rating tools and indices is devised. On the basis of a 3D space frame finite element model (FEM) of SCB and model updating, this paper presents the development of an SHR-oriented 3D multi-scale FEM for the purpose of load-resistance analysis and damage evaluation in structural element level, including modeling, refinement and validation of the multi-scale FEM. The refined 3D structural segments at deck and towers are established in critical segment positions corresponding to maximum cable forces. The components in the critical segment region are modeled as a full 3D FEM and fitted into the 3D space frame FEM. The boundary conditions between beam and shell elements are performed conforming to equivalent stiffness, effective mass and compatibility of deformation. The 3D multi-scale FEM is verified by the in-situ measured dynamic characteristics and static response. A good agreement between the FEM and measurement results indicates that the 3D multi-scale FEM is precise and efficient for WASHMS and SHRS of SCB. In addition, stress distribution and concentration of the critical segments in the 3D multi-scale FEM under temperature loads, static wind loads and equivalent seismic loads are investigated. Stress concentration elements under equivalent seismic loads exist in the anchor zone in steel/concrete beam and the anchor plate edge in steel anchor box of the towers.