• 대한기계학회논문집B
• /
• 제29권5호
• /
• pp.545-553
• /
• 2005

In the present study, The characteristics of developing steady laminar flows of a straight duct connected to a $180^{\circ}$ curved duct were examined In the entrance region through experimental measurement. Flow characteristics such as shear stress distributions, pressure distributions and friction coefficient experimentally in a square cross-sectional straight duct by using the PIV system. For the PIV measurement by particles produced from mosquito coils particles. The experimental data were obtained at 9 points dividing the test sections by 400mm. Experimental results can be summarized as follows. Critical Reynolds number, $Re_{cr}$ which indicates transition from laminar steady flow to transition steady flow was 2,150. Shear stress per unit length on the wall was stronger than that in the fully developed flow region. This was attributed to the fact that shear stress and pressure loss in the curvature of a duct were increased. Pressure distributions were gradually decreased irrespective of Reynolds number In the whole test section. This trends were in a good agreement with the reference results. Pipe friction coefficient in the steady state flow region was calculate from method of least squares. The co-relationship between fiction coefficient and Reynolds number was established as follow; ${\lambda}=56/Re$.

• Journal of Power Electronics
• /
• 제3권3호
• /
• pp.145-150
• /
• 2003

Reliability, availability, and cost have been the major concerns for photovoltaic hybrid systems since their beginning as primary sources for much critical applications like communication units and repeaters. This paper descnbes the performance of two hybrid systems, photovoltaic-battery, wind-turbine coupled with the public-grid (PVBWG) hybrid system and photovoltaic-battery, wind-turbine coupled With the diesel generator (PVBWD) hybrid system The systems are sized to power a typical 300W/48V de telecommunication load continuously throughout the year Such hybrid systems consist of subsystems, which in turn consist of components Failure of anyone of these components may cause failure of the entire system. The reliability and availability basics, and estimation procedure for the two proposals are introduced also in this paper. The PVBWG and PVBWD system configurations are shown with the relevant mean-time-between-faIlure (MTBF) and failure rate (${\lambda}$) of each component. The characteristics equations of the two systems are deduced as a function of operating hours and the percentage of sun and wind availabilities per day. The system probability failure as well as the reliability is estimated based on the fault tree analysis technique. The results show that, by using standard or normal components MTBF, the PVBWG is more reliable and the time of periodic maintenance period is more than one year especially in the rich sites of both sun and wind, but PVBWD competes else Also, in the first five years from the system installation, the system is quit reliable and may not require any maintenance. The results show also, as the sun and wind are available, as the system reliable and available.

• 천문학회보
• /
• 제37권2호
• /
• pp.85.1-85.1
• /
• 2012

Energetic outflow from active galactic nuclei (AGNs) may play a critical role in galaxy evolution. We present a velocity diagnostics for detecting gas outflow in the narrow-line region of Type-2 AGNs using line-of-sight velocity offset of the [O III]${\lambda}5007$ and $H{\alpha}$ emission lines with respect to the systemic velocity of stars in host galaxies. We apply the diagnostics to nearby galaxies at 0.02 < z < 0.05: 3775 AGN-host and 907 star-forming galaxies as a comparison sample, which are selected from the Sloan Digital Sky Survey DR7. After obtaining a best-fit stellar population model for the continuum and a systemic velocity based on stellar lines, we subtract stellar component to measure velocity offsets of each emission line. We find a sample of 169 AGN-host galaxies with outflow signatures, displaying a larger velocity shift of [O III] than that of $H{\alpha}$, as expected in a decelerating outflow model. We find that the offset velocity of [O III] increases with Eddington ratio, suggesting that gas outflow depends on the energetics of AGN.

• Imaging Science in Dentistry
• /
• 제54권2호
• /
• pp.211-220
• /
• 2024

Non-secretory multiple myeloma (NSMM) is a rare cancer of plasma cells characterized by the absence of detectable monoclonal M protein in the blood or urine. A 57-year-old woman presented with mandibular pain but without intraoral swelling. Imaging studies revealed multiple osteolytic lesions in her mandible and pronounced root resorption of the left mandibular second molar. Biopsy results showed atypical plasmacytoid cells positive for anti-kappa, CD138, MUM1, and CD79a antibodies, but negative for anti-lambda and CD20. These results were indicative of a malignant plasma cell neoplasm. No abnormalities were revealed by free light chain assay or by serum or urine protein electrophoresis, leading to a diagnosis of NSMM. The patient began chemotherapy in conjunction with bisphosphonate therapy and achieved remission following treatment. This case underscores the critical role of dentists in the early detection and prevention of NSMM complications, as the disease can initially present in the oral cavity.

• 대한전자공학회논문지SD
• /
• 제45권4호
• /
• pp.57-63
• /
• 2008

본 논문에서는 Contact Etch Stop Layer (CESL)인 nitride film의 mechanical stress에 의해 인가되는 channel stress가 소자 특성에 미치는 영향에 대해 분석하였다. 잘 알려진 바와 같이 NMOS는 tensile stress와 PMOS에서는 compressive stress가 인가되었을 경우 drain current가 증가하였으며 그 원인을 체계적으로 분석하였다. NMOS의 경우 tensile stress가 인가됨으로써 back scattering ratio ($\tau_{sat}$)의 감소와 thermal injection velocity ($V_{inj}$)의 증가로 인해 mobility가 개선됨을 확인하였다. 또한 $\tau_{sat}$, 의 감소는 온도에 따른 mobility의 감소율이 작고, 그에 따른 mean free path ($\lambda_O$)의 감소율이 작기 때문인 것으로 확인되었다. 한편 PMOS의 compressive stress 경우에는 tensile stress에 비해 온도에 따른 mobility의 감소율이 크기 때문에 channel back scattering 현상은 심해지지만 source에서의 $V_{inj}$가 큰 폭으로 증가함으로써 mobility가 개선됨을 확인 할 수 있었다. 따라서 CES-Layer에 의해 인가된 channel stress에 따른 소자 특성의 변화는 inversion layer에서의 channel back scattering 현상과 source에서의 thermal injection velocity에 매우 의존함을 알 수 있다.

• Steel and Composite Structures
• /
• 제5권2_3호
• /
• pp.181-192
• /
• 2005

The effective length method for flexural (column) buckling has been used for many decades but its use is somewhat limited in various contemporary design codes to moderately slender structures with elastic critical load factor (${\lambda}_{cr}$) less than 3 to 5. In pace with the use of higher grade steel in recent years, the influence of buckling in axial buckling resistance of a column becomes more important and the over-simplified assumption of effective length factor can lead to an unsafe, an uneconomical or a both unsafe and uneconomical solution when some members are over-designed while key elements are under-designed. Effective length should not normally be taken as the distance between nodes multiplied by an arbitrary factor like 0.85, 1.0, 2.0 etc. Further, the classification of non-sway and sway-sensitive frames makes the conventional design procedure tedious to use and, more importantly, limited to simple regular frames. This paper describes the practical use of second-order analysis with section capacity check allowing for $P-{\delta}$ and $P-{\Delta}$ effects together with member and system imperfections. Most commercial software considers only the $P-{\Delta}$ effect, but not member and frame imperfections nor $P-{\delta}$ effect, and engineers must be very careful in their uses. A verification problem is also given for validation of software for this type of powerful second-order analysis and design. It is a trend for popular and advanced national design codes in using the second-order analysis as a norm for analysis and design of steel structures while linear analysis may only be used in very simple structures.

• 한국조경학회지
• /
• 제33권4호
• /
• pp.97-107
• /
• 2005

This study was carried out to construct accurate and scientific system of assessment indicators in selection of National Trust conservation areas, which was new concept of domestic environment movement and offer the raw data of new analytic method by introducing the fuzzy theory and weight for overcoming the uncertainty of ranking decision. To transform the Likert's scale granted to assessment indicators into the type of triangular fuzzy number(a, b, c), there was conversion to each minimum(a), median(b), and maximum(c) in applying membership function, and in using the center of gravity and eigenvalue, there was to decide the ranking. The rankings of converted values applied a mean importance and weight were confirmed that they were generally changed. Therefore, the ranking decision was better to accomplish objective and rational ranking decision by applying weight that was calculated in grouping of indicator than to judge the singular concept and to be useful in assessment of diverse National Trust site. In the future, because AHP, which was general method of calculating weight, was lacked, there was to understand the critical point to fix a pertinent weight, and to carry out the study applying engineering concept like fuzzy integral using $\lambda-measure$.

• 한국재료학회지
• /
• 제15권6호
• /
• pp.361-369
• /
• 2005

InP(100) crystal surface was irradiated by ion beams with low energy $(180\~225\;eV)$ and high flux $(\~10^{15}/cm^2/s)$, Self-organization process induced by ion beam was investigated by examining nano structures formed during ion beam sputtering. As an ion source, an electrostatic closed electron Hall drift thruster with a broad beam size was used. While the incident angle $(\theta)$, ion flux (J), and ion fluence $(\phi)$ were changed and InP crystal was rotated, cone-like, ripple, and anistropic nanostrucuture formed on the surface were analyzed by an atomic force microscope. The wavelength of the ripple is about 40 nm smaller than ever reported values and depends on the ion flux as $\lambda{\propto}J^{-1/2}$, which is coincident with the B-H model. As the incident angle is varied, the root mean square of the surface roughness slightly increases up to the critical angle but suddenly decreases due to the decrease of sputtering yield. By the rotation of the sample, the formation of nano dots with the size of $95\~260\;nm$ is clearly observed.

• 한국염색가공학회지
• /
• 제22권3호
• /
• pp.187-193
• /
• 2010

The effects of molecular weight (MW) and concentration on the rheological properties of poly(vinyl alcohol) (PVA) solutions in dimethyl sulfoxide (DMSO) were investigated at $30^{\circ}C$. Ubbelohde viscometer and rotational rheometer were employed for dilute and concentrated regime, respectively. In the dilute regime, the Mark-Houwink exponent ($\alpha$) of the solutions determined from three different MWs proved 0.73. The critical concentration (C*), in which the entanglement and overlap of polymer molecules began to take place, decreased with increasing the MW of PVA. Huggins constant ($K_H$) values ranged from 0.33 to 0.45 over the MW examined. In the log-log plot of $\eta_{sp}$ versus [$\eta$]C, the PVA with higher degree of polymerization (DP) gave a greater slope exhibiting the inflection point in the vicinity of C*. In the dynamic viscosity ($\eta'$) curve, the PVA solutions of DP 1700 presented Newtonian fluid behavior over most of the frequency range examined. However, the lower Newtonian flow region reduced with increasing the DP. As the PVA concentration increased, $\eta'$ was increased and the onset shear rate for pseudoplasticity was decreased. In the Cole-Cole plot, PVA solutions showed almost a single master curve in a slope of ca. 1.65 regardless of the DP. However, the increase of the concentration from 8 to 12 wt% for PVA solutions of DP 5000 decreased the slope from 1.73 to 1.57. In the tan $\delta$ curve, the onset frequency for sol-gel transition was shifted from 154 to 92 rad/s with increasing the DP from 3300 to 5000 and from 192 to 46 rad/s with increasing the concentration from 8 to 12 wt%. In addition, longer relaxation time ($\lambda$) was observed with increasing the DP and concentration.

• 한국광학회지
• /
• 제12권4호
• /
• pp.312-319
• /
• 2001

본 연구에서는 기존의 RWG LD(Ridge waveguide laser diode)보다 Ridge 폭의 제어가 쉽고 Planar화에 유리하며 측방향의 굴절률차를 성장층의 두께로 조절이 가능한 Buried RWG LD를 제안하였다. 이론해석의 결과로부터 효율적으로 동작하는 MQW B-RWG(Multi-quantum well buried ridge waveguide)LD를 제작하기 위해서는 제작하고자 하는 Ridge 폭에 따라 측장향 유효굴절률차 $\Delta_{nL}$ 의 임계값보다 약간 크게 되도록 유효굴절률 조절을 위한 $d_2(\lambda_g=1.25{\mu}m, InGaAsP layer) 층과 P-InP cald 층인 $d_3$층의 두께를 제어해야 하며 임계전류값이 최소로 되면서 측방향에서 단일모드로 동작하도록 Ridge 폭을 설계해야 한다. 그리고 측방향 유효굴절률차를 적절히 조절한다면 $6~9{\mu}m$의 Ridgechr을 가지면서 단일모드로 동작하는 LD제작이 가능함을 알 수 있었다.