• Steel and Composite Structures
• /
• 제22권2호
• /
• pp.429-448
• /
• 2016

This paper presents a finite element (FE) model for predicting the behaviour of steel column-column connections under axial compression and tension. A robustness approach is utilised for the design of steel column-column connections. The FE models take into account for the effects of initial geometric imperfections, material nonlinearities and geometric nonlinearities. The accuracy of the FE models is examined by comparing the predicted results with independent experimental results. It is demonstrated that the FE models accurately predict the ultimate axial strengths and load-deflection curves for steel column-column connections. A parametric study is carried out to investigate the effects of slenderness ratio, contact surface imperfection, thickness of cover-plates, end-plate thickness and bolt position. The buckling strengths of steel column-column connections with contact surface imperfections are compared with design strengths obtained from Australian Standards AS4100 (1998) and Eurocode 3 (2005). It is found that the column connections with maximum allowable imperfections satisfy the design requirements. Furthermore, the steel column-column connections analysed in this paper can be dismantled and reused safely under typical service loads which are usually less than 40% of ultimate axial strengths. The results indicate that steel column-column connections can be demounted at 50% of the ultimate axial load which is greater than typical service load.

• 기술사
• /
• 제5권19호
• /
• pp.3-16
• /
• 1972

1. Purposes and importances of the study. In gaining heating resources by combustion of briquette, which is the necessaries of every day's life, victims occur from poisonous affection of combustion gas (carbon mono-oxide) in every year and this gas attributable to increase death rate proportion to the high demand of briquette usage. It arise great problem ill point of national sanitation. Therefore, the study has a big aim to accomplish depressing CO gas or stimulating comlete combustion by both the methods of physical improvement of present combustion devices and chemical improvement by using V$_2$O$\sub$5/ catalyst to depress CO gas or fasten complete combustion Progress. Sucessful result of this study will not only to decrease the death rate but also to contribute fearless handling of briquette combustion so as to perform improving public Welfare. 2. Contents and scope of study. A. comparison of present and improved fuel hole device. B. Examination of effectness of improved elements. C. Effectness of miffed usage of catalyst. D. Comparison of Catalyst effectness. E. Examination of effectness of black slate containing V$_2$O$\sub$5/. 3. Results and recommendations of the study A. Absolute necessity of supplying secondary air by improved combustion device. B. Oxide Vanadium (V$_2$O$\sub$5/) has the greatest effectness to eliminate CO gas. C. Most effective catalyst of V$_2$O$\sub$5/ containing slate comes from "Samgoe" coal mine. D. By plastering catalyst on the cover plate of fire hole, it stimulate chemical reaction of re-combustion and preserving heat. E. Recommend to continute further precise study to practice with low-cost and handy devices to be applied the study results.

• 한국산학기술학회논문지
• /
• 제17권12호
• /
• pp.34-40
• /
• 2016

소비자들의 요구 증가로 고급차종에만 적용하던 통풍 시트는 점차 중소형 차종으로 확대 적용되고 있는 추세이다. 팬에서 발생한 유량이 폼 패드, 필터 폼 및 시트 커버 등을 통과하는 과정에서 많은 손실이 발생하기 때문에, 착좌면에 도달하는 유량의 정확한 해석은 쉽지 않다. 또한 유로 형상이 복잡하여 이의 정확한 모델링 없이는 착좌면에 도달하는 정확한 유량의 해석이 힘들다. 본 연구에서는 팬에서 발생한 유동이 통기 매트와 폼 패드를 통과하였을 때의 유량을 해석하였으며, 해석결과와 실험결과를 비교하였다. 해석에서 유동분산판 내부의 돌기 형상을 보다 정확하게 모델링함으로써, 해석결과와 실험결과의 경향을 정확하게 일치시킬 수 있었다. 유량이 통기성 재료인 패드 폼을 통과하는 과정에서 발생한 손실을 실험으로 측정하여 해석결과를 보정함으로써 해석결과와 실험결과를 정확하게 일치시킬 수 있었다. 다음으로 필터 폼과 시트 커버를 통과하여 착좌면에 도달하는 유량을 실험으로 측정하였다. 착좌면에서의 유량이 많지 않아서, 유량 콘을 사용하여 유량을 측정하였다. 팬에서 발생한 유량의 약 35.7%만이 최종적으로 착좌면에 도달하는 것을 확인할 수 있었다.

• 콘크리트학회논문집
• /
• 제28권2호
• /
• pp.129-139
• /
• 2016

대형 PC기둥의 양중부하를 줄이고 접합부의 구조일체성을 개선하기 위한 대안으로서, 중공 PC기둥이 사용될 수 있다. 본 연구에서는 PC부의 생산성과 구조일체성을 개선한 새로운 중공 PC기둥을 개발하였다. PC부를 제작하기 위하여 구조용 골형플레이트를 내부영구거푸집과 수평 관통철근을 사용하였다. 제안된 PC기둥의 내진성능을 검증하기 위하여, 1/2 스케일의 기둥 실험체 4개에 대하여 일정 축력에서 반복 횡가력실험을 수행하였다. 실험 변수로는 횡철근 간격, 강섬유 사용여부, 그리고 PC부의 두께가 고려되었다. 실험 결과, 제안된 PC기둥은 외곽 PC부의 취성적인 파괴 없이 우수한 하중재하능력과 변형능력을 보이는 것으로 나타났다. PC부에 횡철근을 촘촘히 배근하거나 강섬유를 사용할 경우, PC 콘크리트의 탈락을 제한하여 변형능력을 증가시킬 수 있었다.

• Archives of Plastic Surgery
• /
• 제32권3호
• /
• pp.293-298
• /
• 2005

Osseointegrated prosthetic auricular reconstruction can be classified as either direct or indirect. In the $Br{\aa}nemark $ system of direct osseointegration, implants are placed into the mastoid process of the temporal bone. In the Epitec system of indirect osseointegration, implants are inserted into a three-dimensional carrier plate that is fixed to the mastoid by means of screws. We experienced forty-four cases using the indirect system and seventeen cases using the direct system. We compared with two systems by complications, such as skin reaction, implant loosening, implant loss. There were no specific differences in the skin reaction around the implants and abutments in relation to age or system used. The degree of skin reaction was different according to the conditions around the implant: in cases of virgin microtia, a skin flap was used to cover the implant, in contrast to grafted skin coverage for failed autogenous reconstruction. In both systems, the skin reaction was more severe and frequent in skin flap than in grafted skin. Loosening of the implant was more frequent in the direct system; however, accidental detachment of the implant from the abutment was more frequent in the indirect system. To reduce complications of skin reaction in osseointegrated prosthetic auricular reconstruction, it is important for soft tissue around implant to immobilize. Therefore, grafted skin is better than skin flap as soft tissue around implant. And immobilization of soft tissue around implant by wound dressing is major facter.

• 한국농공학회지
• /
• 제16권2호
• /
• pp.3430-3437
• /
• 1974

.It is very importaut to know the water consumption of crops in planning irrigation works and practicing suitable soil moisture management. For the purpose of making it clear that how much water be consumed to cultivate the Chinese cabbage, Chamber method has been applied. Main equipments in the transpiration chamber are flowers, manometer and electric thermograph. The chamber made of vynyl plate has a small entrance at the base and an exit at the top, and the ventilation in the chamber was carried out by a flower through the entrance and exit. Air-flow adjusted by an orifice manometer enters the chamber from the outside over the crop canopy through the pipe like a chimney and finally goes out to the outside. Two sets which consist of a pair of dry and wet bulb made by thermistor are installed in the entrance and exit tube, and record air temperature automatically. Evapotranspiration amount is computed from the air-flow quantity and difference in absolute humidity between at the entrance and exit of the chamber by the following equation: ET=(X2-X1)${\times}$Q where ET=evapotranspiration amount X1=absolute humidity at the entrance(g/㎥) X2=absolute humidity at the exit(g/㎥) Q=air-flow quantity(㎥) This study was carried out at the upland farm of the Institute of Agriculture Engimeering and Utilization, Suwon, Korea. from 1971 to 1973. The results obtained in this experiment are as follows: 1. The total amount of evapotranspiration of Chinese Cabbage that is cultivated in autumn is 408.1mm during growth period. 2. Chinese cabbage rapidly grows up in the second ten days of September, 40th to 50th days after seeding. At the same time, the maximum amount of evaportranspiration of Chinese cabbage is 61.6mm/10 days 3. The correlation between Pan-evaporation and evapotranspiration is high, coefficient of correlation r=0.88**, and can be shown as The following regression equation: ET=0.913E+20.273 4. Evapotranspiration is closely related with meteorological factors: r=0.85**, for insolation, r=0.76** for air temperature, respectively. 5. The percentage of evapotranspiration amount, at the beginning of growth stage, gradually increases in proportion as the Chinese Cabbage grows but is largely affected by meteorological factors after the green cover formation. 6. By Blaney and Griddle formula, evaportranspiration coefficient "K" are within from 0,85 to 1.27.

• Bulletin of the Korean Chemical Society
• /
• 제33권4호
• /
• pp.1135-1140
• /
• 2012

An electrochromatographic microchip with carboxyl-group-derivatized mono-disperse silica packing was prepared from the corresponding colloidal silica solution by utilizing capillary action and self-assembly behavior. The silica beads in water were primed by the capillary action toward the ends of cross-patterned microchannel on a cyclic olefinic copolymer (COC) substrate. Slow evaporation of water at the front of packing promoted the self-assembled packing of the beads. After thermally binding a cover plate on the chip substrate, reservoirs for sample solutions were fabricated at the ends of the microchannel. The packing at the entrances of the microchannel was silver coated to fix utilizing an electroless silver-plating technique to prevent the erosion of the packed structure caused by the sudden switching of a high voltage DC power source. The electrochromatographic behavior of the microchip was explored and compared to that of the microchip with bare silica packing in basic borate buffer. Electrophoretic migration of Rhodamine B was dominant in the microchip with the carboxyl-derivatized silica packing that resulted in a migration approximated twice as fast, while the reversible adsorption was dominant in the bare silica-packed microchip. Not only the faster migration rates of the negatively charged FITC-derivatives of amino acids but also the different migration due to the charge interaction at the packing surface were observed. The electrochromatographic characteristics were studied in detail and compared with those of the bare silica packed microchip in terms of the packing material, the separation potential, pH of the running buffer, and also the separation channel length.

• Design & Manufacturing
• /
• 제16권4호
• /
• pp.24-33
• /
• 2022

Fiber-reinforced plastics(FRPs) have excellent specific stiffness and strength, so they are usually used as automotive parts that require high rigidity and lightweight instead of metal. However, it is difficult to predict the mechanical properties of injection molded parts due to the fiber orientation and breakage of FRPs. In this paper, the fiber orientation characteristics and mechanical properties of injection molded specimens were evaluated in order to fabricate automotive transmission side covers with FRPs and design a rib structure for improvement of their rigidity. The test molds were designed and manufactured to confirm the fiber orientation characteristics of each position of the injection molded standard plate-shaped specimens, and the tensile properties of the specimens were evaluated according to the injection molding conditions and directions of specimens. A gusset-rib structure was designed to improve the additional structural rigidity of the target products, and a proper rib structure was selected through the flexural tests of the rib-structured specimens. Based on the evaluation of fiber orientation and mechanical characteristics, the optimization analyses of gate location were performed to minimize the warpage of target products. Also, the deformation analyses against the internal pressure of target product were performed to confirm the rigidity improvement by gusset-rib structure. As a result, it could be confirmed that the deformation was reduced by 27~37% compared to the previous model, when the gusset-rib structure was applied to the joining part of the target products.

• 대한토목학회논문집
• /
• 제28권2A호
• /
• pp.233-242
• /
• 2008

본 연구는 지진운동의 영향 하에서 강제 모멘트 골조로 이루어진 post-Northridge(덮개판) 연결부를 갖는 보의 탄성 및 비탄성 거동을 모델하기 위한 부등단면 보(IBS 보) 요소를 제시한다. 덮개판(IBS) 연결부를 갖는 부등단면 보의 탄성강성 매트릭스는 수치적분이 필요치 않은 수식으로 표현된다. 소성모델은 분포형이며 강체링크로 연결된 일련의 비선형 힌지로 구성 되어있고 경화법칙은 단조 및 임의 주기 하중에 대한 비탄성 거동과 국부좌굴의 효과를 고려할 수 있다. 또한 IBS 보 요소에 대한 항복면, 강성 변수, 그리고 경화(혹은 연화) 법칙 변수의 결정과정을 기술하였고 IBS 보 요소의 해석결과를 실험 및 FEM 해석결과와 비교하였다. IBS 보 요소의 해석결과는 실험 및 FEM 결과와 좋은 상관관계를 보였다.

• 대한토목학회논문집
• /
• 제6권1호
• /
• pp.1-11
• /
• 1986

강구조물(鋼構造物)의 girder중(中) 중요형식(重要形式)인 판항(板桁)에서 덮개판(板) 및 수직보강재(垂直補剛材)와 판항(板桁)이나 상자항(箱子桁)의 격점부(格點部)에 사용도는 연결판(連結板) 등의 용접연결부(鎔接連結部)를 포함하는 실물(實物)을 modeling하여 직접 피로시험(疲勞試驗)을 행하지 않고서도 계산에 의하여 S-N 선도(線圖)를 그려서 피로강도(疲勞强度)를 추정(推定)할 수 있는 계산식 및 program을 정립하였다. 또, 실물시험편(實物試驗片)에 대한 피로시험(疲勞試驗)을 행하여 계산에 의한 S-N 선도상(線圖上)에 plot하여 서로 비교 검토하였다. 이로써 다음과 같은 결과를 얻었다. 계산에 의한 피로강도(疲勞强度)가 실험(實驗)에 의한 실제 피로강도(疲勞强度)보다 다소 낮게 나타났다. 계산에 의한 방법은 초기균열(初忌龜裂) $a_i$가 발생한 다음부터 파단시(破斷時)까지의 피로수명(疲勞壽命) $N_p$에 대한 것임에 비해 실험(實驗)에 의한 것은 초기균열(初忌龜裂) $a_i$의 발생수명(發生壽命) $N_c$까지를 포함한 총(總) 피로수명(疲勞壽命) $N=N_c+N_p$에 대한 것이므로 오히려 당연한 결과라 생각된다. 그 차이가 그다지 크지 않으며, 구조물(構造物)의 안전성(安全性)을 생각할 때 계산(計算)에 의한 결과가 안전측(安全側)에 해당하므로 실제 구조물(構造物)의 피로설계(疲勞設計) 시(時) 그대로 적용하여도 무방할 것으로 생각된다. 참고로 저강도강(低强度鋼)인 SS 41 시험편(試驗片)을 각 경우 3개씩 제작하여 같은 피로시험(疲勞試驗)을 행하여 비교해 보았다. 덮개판(板)의 경우 시험최대응력(試驗最大應力) $14kg/mm^2$ 정도 이상(以上)에서 서서히, 수직보강재(垂直補剛材)의 경우 실험최대응력(實驗最大應力) $31kg/mm^2$ 정도 이하(以下)에서 급격(急激)히, 고강도강(高强度鋼)인 SWS 50 시험편(試驗片)의 경우보다 피로강도(疲勞强度)가 더 커진 경향을 나타내고 있다. 이는 저강도강(低强度鋼)에서 피로강도(疲勞强度)가 낮을 것이라는 상식적(常識的)인 기대와는 다른 특징(特徵)이지만 시험편(試驗片) 3개씩만의 결과이므로 확정적(確定的)인 결론이라고 단언(斷言)할 수는 없겠으며, 앞으로 더 많은 실험(實驗)을 행하여 확인해 보아야 할 것이라 생각된다.