• 대한치과보철학회지
• /
• 제26권1호
• /
• pp.31-49
• /
• 1988

This study was performed to investigate the sound distortion following the alternation of the palatal plate thickness, for this study, 3 subjects who were born in Seoul and spoke Seoul dialect were recruited from K university male student population. First, their sounds of /아(a)/, 어(e)/, 오(o)/, 우(u)/, 으($\.{+}$), 이(i)/,에(e)/ without inserting plate were recorded , and then the sounds with palatal plates of different thickness were recorded, respectively. The palatal plates was constructed to cover the alveolar & palatal surfaces of the maxilla with an approximate thickness of 1.0mm, 2.5mm, and thickness of 2.5mm over the alveolar ridge & 1.0mm elsewhere and, named B, C, D-type, in succession. Series of analysis were administered through Computer (16 bit IBM PC/AT) at analyze the sound distortions. These experiments were analyzed by the LPC, Log Area Ratio. The findings led to the following conclusions: 1. Sound distortions were relatively minute in each condition and informations, however, /이(i)/ was the most distorted vowel in all conditions. 2. By and large, sound distortion was large in C, D-types. However, there was no correlation of the distortion rate on the 3 informants, and all tested vowels. 3. It was similar to LPC, Log Area Ratio distortion rates. 4. It was found that the sound distortion wit]1 plate inserted was verified to the numeric value with LPC and Log Area Ratio method.

• Structural Engineering and Mechanics
• /
• 제9권5호
• /
• pp.417-432
• /
• 2000

A comprehensive analytic study has been conducted to investigate the instability problems of metal-plate-connected (MPC) joints in light frame trusses. The primary objective in this study is to determine the governing factors that constitute the buckling of the metal connectors and their effects on the structural response of joints. Another objective is to recommend design curves for the daily structural design of these joints. The numeric data presented in this paper has emerged from a broad base that was founded on over 350 advanced computer simulations, and was supported by available experimental results obtained by others. This basic-to-applied research includes practical engineering parameters such as size of gaps, shear lengths, gauge (plate thickness) of connectors, size of un-braced areas, failure modes, and progressive disintegration of joints. Square-end members have been emphasized though the results cover the custom-made fitted joints. The results indicate that chord shears cause and dominate the buckling of MPC joints, and the shear length has a more pronounced effect than the size of gaps. Further, large gauges and small un-braced areas improve the buckling response. Several practical recommendations have been suggested throughout the paper such as keeping the ratio of gap/shear length below 3/4 for improving the buckling strength. The study reveals that multi-area joints should not be simplified as single web-to-chord MPC joints such as keeping the ratio of gap/shear length below 3/4 for improving the buckling strength, even where one web is in tension and the other in compression. Finally, the results obtained from this study favorably agree with experimental data by others, and the classic buckling theories for other structural components.

• 한국강구조학회 논문집
• /
• 제16권5호통권72호
• /
• pp.575-586
• /
• 2004

본 논문은 새롭게 개발된 춤이 깊은 데크 플레이트(이하 Deep Deck) 및 비대칭 H형강 하부플랜지에 플레이트를 용접한 비대칭 철골보로 구성된 매립형(슬림플로어) 합성보의 웨브면에 개구부를 가진 유공 합성보의 휨성능에 관한 실험적 연구이다. 실험은 철골보 춤(250mm, 300mm), 개구부의 위치 및 가력조건에 따라 5개의 유공 합성보에 대한 단순지지 휨실험 수행하였다. 실험결과, 매립형 유공합성보는 전단연결재를 사용하지 않고도 콘크리트의 면내 부착력에 의해 충분한 합성작용을 하는 것으로 나타났고, 개구부 주변이 콘크리트에 의해 구속되어 개구부의 보강없이 충분한 구조적 성능을 발휘할 수 있음을 확인하였다.

• 대한기계학회논문집A
• /
• 제29권2호
• /
• pp.247-252
• /
• 2005

This research presents a three-dimensional modeling technique for a flexible sheet. A relative coordinate formulation is used to represent the kinematics of the sheet. The three-dimensional flexible sheet is modeled by multi-rigid bodies interconnected by out-of-plane joints and plate force elements. A parent node is designated as a master body and is connected to the ground by a floating joint to cover the rigid motion of the flexible sheet in space. Since the in-plane deformation of a sheet such as a paper and a film is relatively small, compared to out-of-plane deformation, only the out-of-plane deformation is accounted for in this research. The recursive formulation has been adopted to solve the equations of motion efficiently. An example is presented to show the validity of the proposed method.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.80.1-80.1
• /
• 2011

This study was carried out in order to estimate the effect of heat pump performance by use of thermal tank with 3 seperation plates which were able to divide thermal tank into 3 chambers that have different temperatures levels. For testing the effect of developed thermal tank which was installed for supplying the heat to the paprika greenhouse in Jinju city. The volume of thermal storage tank was designed for $110m^3$ which was able to cover 30% of heating capacity. The temperature difference was 3 degree Celcius between high temperature and low temperature when only heating circulation was made from heat pump to thermal tank. but 5.5 degree Celcius difference was made when heating circulation of heat pump to thermal thank and hot water supplying circulation of thermal tank to greenhouse was done simultaneously. As a result of this study showed that COP of heat pump was increased by 15% or more than that of using normal thermal tank because heat pump was able to take 3 ~ 5 degree Celcius lower thermal thank water constantly.

• Journal of Mechanical Science and Technology
• /
• 제19권spc1호
• /
• pp.305-311
• /
• 2005

This research presents a three-dimensional modeling technique for a flexible sheet. A relative coordinate formulation is used to represent the kinematics of the sheet. The three-dimensional flexible sheet is modeled by multi-rigid bodies interconnected by out-of-plane joints and plate force elements. A parent node is designated as a master body and is connected to the ground by a floating joint to cover the rigid motion of the flexible sheet in space. Since the in-plane deformation of a sheet such as a paper and a film is relatively small, compared to out-of-plane deformation, only the out-of-plane deformation is accounted for in this research. The recursive formulation has been adopted to solve the equations of motion efficiently. An example is presented to show the validity of the proposed method.

• Steel and Composite Structures
• /
• 제19권5호
• /
• pp.1299-1319
• /
• 2015

This paper presents a detailed parametric study, conducted using finite element tools to cover a range of several geometric and material parameters, on the behaviour of thin-walled partially encased composite (PEC) columns. The PEC columns studied herein are composed of thin-walled built-up H-shaped steel sections with concrete infill cast between the flanges. Transverse links are provided between the opposing flanges to improve resistance to local buckling. The parametric study is confined to eccentrically-loaded columns subjected to major axis bending only. The parameters that were varied include the overall column slenderness ratio (L/d), load eccentricity ratio (e/d), link spacing-to-depth ratio (s/d), flange plate slenderness ratio (b/t) and concrete compressive strength ($f_{cu}$). The overall column slenderness ratio was chosen to be the primary variable with values of 5, 10 and 15. Other parameters were varied within each case of L/d ratio. The effects of the selected parameters on the behaviour of PEC columns were studied with respect to the failure mode, peak axial load, axial load versus average axial strain response, axial load versus lateral displacement response, moment versus lateral displacement behaviour and the axial load-moment interaction diagram. The results of the parametric study are presented in the paper and the influences of each of the parameters investigated are discussed.

• Journal of Ship and Ocean Technology
• /
• 제8권4호
• /
• pp.26-33
• /
• 2004

PFFEM software, PFADS has been developed for the vibration predictions and analysis of coupled system structures in medium-to-high frequency ranges. PFFEM is numerical method which solves energy governing equation using finite element technique for complicated structures where the exact solutions are not available. Through the upgrades, present PFADS R3 could cover the general beam and plate structures including various kinds of beam-plate rigid joints and other joint systems such as spring-damper junction and rigid bar connection. This software is composed of 3 parts; translator, model converter and solver. The translator makes its own FE-model from bulk data of commercial FE software, and the model converter is used to convert FE-model to PFFE-model automatically. The solver calculates vibrational energy density and intensity for PFFE-model by solving global matrix equations of PFFEM. For the applications of real transportation systems, a container ship model has been examined with respect to major parameters, and reliable results have been obtained.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.573-576
• /
• 2005

This research presents a three-dimensional modeling technique for a flexible sheet. A relative coordinate formulation is used to represent the kinematics of the sheet. The three-dimensional flexible sheet is modeled by multi-rigid bodies interconnected by out-of-plane joints and plate force elements. A parent node is designated as a master body and is connected to the ground by a floating joint to cover the rigid motion of the flexible sheet in space. Since the in-plane deformation of a sheet such as a paper and a film is relatively small, compared to out-of-plane deformation, only the out-of-plane deformation is accounted for in this research. The recursive formulation has been adopted to solve the equations of motion efficiently. An example is presented to show the validity of the proposed method.

• Steel and Composite Structures
• /
• 제41권5호
• /
• pp.747-759
• /
• 2021

Built-up Double-I (BD-I) columns have been commonly used for mid-rise steel-frame structures in Iran. These columns consist of two hot rolled IPE sections which are connected by two cover plates and fillet welds. Until 2017, BD-I columns were employed in intermediate moment resisting frames (MRF) using welded flange plate (WFP) connections. To evaluate the seismic behavior of the connections, four samples were made and tested based on cyclic loading according to AISC 341-16. It was concluded that typical samples cannot satisfy the seismic provisions related to intermediate MRFs. In contrast, the proposed connections retrofitted with two-part external diaphragms were able to satisfy not only the seismic requirements related to intermediate MRFs but also those related to special MRFs according to AISC. The numerical modeling of these samples was performed using ABAQUS finite element software. This study compared the hysteresis moment-rotation curves, plastic strains, and behavior modes in both experimental samples and numerical models.