• Journal of the Optical Society of Korea
• /
• v.18 no.5
• /
• pp.569-573
• /
• 2014

We demonstrate a low-cost, superbly efficient way of etching for the nano-, and micro-sized pyramid patterns on (100)-oriented Si wafer surfaces for use as a patterned master. We show a way of producing functional optical films for the viewing angle direction brightness-enhancement of Lambertian LED (light emitting diode)/OLED (organic light emitting diode) planar lighting applications. An optimally formulated KOH (Potassium hydroxide) wet etching process enabled random-positioned, and random size-distributed (within a certain size range) pyramid patterns to be developed over the entire (100) silicon wafer substrates up to 8" and a simple replication process of master patterns onto the PC (poly-carbonate) and PMMA (poly-methyl methacrylate) films were performed. Haze ratio values were measured for several film samples exhibiting excellent values over 90% suitable for LED/OLED lighting purposes. Brightness was also improved by 13~14% toward the viewing angle direction. Computational simulations using LightTools$^{TM}$ were also carried out and turned out to be in strong agreement with experimental data. Finally, we could check the feasibility of fabricating low-cost, large area, high performance optical films for commercialization.

• ETRI Journal
• /
• v.37 no.1
• /
• pp.32-42
• /
• 2015

Orthogonal frequency-division multiplexing (OFDM) suffers from spectral nulls of frequency-selective fading channels. Linear precoded (LP-) OFDM is an effective method that guarantees symbol detectability by spreading the frequency-domain symbols over the whole spectrum. This paper proposes a computationally efficient and low-cost implementation for discrete Hartley transform (DHT) precoded OFDM systems. Compared to conventional DHT-OFDM systems, at the transmitter, both the DHT and the inverse discrete Fourier transform are replaced by a one-level butterfly structure that involves only one addition per symbol to generate the time-domain DHT-OFDM signal. At the receiver, only the DHT is required to recover the distorted signal with a single-tap equalizer in contrast to both the DHT and the DFT in the conventional DHT-OFDM. Theoretical analysis of DHT-OFDM with linear equalizers is presented and confirmed by numerical simulation. It is shown that the proposed DHT-OFDM system achieves similar performance when compared to other LP-OFDMs but exhibits a lower implementation complexity and peak-to-average power ratio.

• Journal of Communications and Networks
• /
• v.17 no.1
• /
• pp.84-92
• /
• 2015

Multi-hop relay networks have been widely considered as a promising solution to extend the coverage area and to reduce the deployment cost by deploying the relay stations (RSs) in mobile communication systems. Suitable deployment for the RSs is one of the most important features of the demand nodes (DNs) to obtain a high data transmission rate in such systems. Considering a tradeoff among the network throughput, the deployment budget, and the overall coverage of the systems, efficient RS deployment schemes and corresponding algorithms must be developed and designed. A novel cluster-based RS deployment scheme is proposed in this paper to select the appropriate deployment locations for the relay stations from the candidate positions. To make an ideal cluster distribution, the distances between the DNs are calculated when deploying the RSs. We take into account the traffic demands and adopt a uniform cluster concept to reduce the data transmission distances of the DNs. On the basis of the different candidate positions, the proposed scheme makes an adaptive decision for selecting the deployment sites of the RSs. A better network throughput and coverage ratio can be obtained by balancing the network load among the clusters. Simulation results show that the proposed scheme outperforms the previously known schemes in terms of the network throughput and the coverage ratio. Additionally, a suitable deployment budget can be implemented in multi-hop relay networks.

• Korean Journal of Pharmacognosy
• /
• v.49 no.1
• /
• pp.65-69
• /
• 2018

Torilin is a major sesquiterpene of Torilis japonica (Umbelliferae) fruits and known to be a melanogenesis inhibitor. Extraction conditions are important factor for the efficient preparation to save cost and time in economic aspects. For this reason, this study was conducted to optimize the extraction condition for maximal yield of torilin. For optimization, extraction factors such as extraction solvent, extraction temperature and sample/solvent ratio were tested and optimized for maximum yield of torilin using response surface methodology with Box-Behnken design (BBD). The optimal condition was obtained as a EtOAc concentration in MeOH of 31.8%, an extraction temperature at $30.3^{\circ}C$ and a sample/solvent ratio, 1000 mg/2 ml. The torilin yield under optimal conditions was found to be 9.9 mg/g dried samples, which were well-matched with the predicted value of 10.4 mg/g dried samples. These results will provide useful information about optimized extraction conditions for the development of torilin as cosmetic therapeutics to reduce skin hyperpigmentation.

• Environmental Engineering Research
• /
• v.23 no.4
• /
• pp.364-373
• /
• 2018

The present study assessed the efficient removal of nutrients and Chlorophyll-a (Chl-a) by using methyl esterified sericite (MES) and pine needle extracts (PNE), a low cost and abundant green hybrid material from nature. For this purpose, the optimal conditions were investigated, such as the pH, temperature, MES and PNE ratio, and MES-PNE dose. In addition, a Microcystis aeruginosa control using MES-PNE was also analyzed with various inhibition models. The removal of the nutrient and Chl-a onto MES-PNE was optimized for over 95% removal as follows: 2-2.5 for the MES-PNE ratio, 7-8 pH and a $22-25^{\circ}C$ temperature. In this respect, approximately 1.52-2.20 g/L of MES-PNE was required to remove each 1 g of dry weight/L of Chl-a. Total phosphorus (TP) has a greater influence on the increase in Chl-a than total nitrogen (TN) according to the correlation between TN, TP and Chl-a. Moreover, the Luong model was the best model for fitting the biodegradation kinetics data from Chl-a on MES-PNE from lake water. The novel hybrid material MES-PNE was very effective at removing TN, TP and Chl-a from the lake and can be applied in the field.

• Journal of information and communication convergence engineering
• /
• v.4 no.4
• /
• pp.170-173
• /
• 2006

Recently, with increasing efficiency of DSC (photo-electrochemical using a nano-particle), The Performance of DSC solar generation system also needs improvement. The approach consists of a Fly-back DC-DC (transfer ratio 1:10) converter to boost the DSC cell voltage to 300VDC. The four switch (MOSFET) inverter is employed to produce 220V, 60Hz AC outputs. High performance, easy manufacturability, lower component count., safety and cost are addressed. Protection and diagnostic features form an important part of the design. Another highlight of the proposed design is the control strategy, which allows the inverter to adapt to the: requirements of the load as well as the power source. A unique aspect of the design is the use of the DSP TMS320LF2406 to control the inverter by current and voltage feed-back. Efficient and smooth control of the: power drawn from the DSC Cell is achieved by controlling the front end DC-DC converter in current mode.

• International Commerce and Information Review
• /
• v.8 no.2
• /
• pp.165-183
• /
• 2006

Sea transport industry is service industry and basic industry that permit efficient division of the human and material resources of industry. Also, owing to geographical situation which korea is having, utilization ratio of sea logistics industry is high than other transport ways. Sea transport industry chieves role that promote economy activity of other industry field as well as offer of transport way. Specially, because unit anger of freight by container is introduced, it was achived reduction of transport unit cost and mechanization of loading and unloading by this result. For efficeint connection of each other transport, contianer had offerd to large ship. Quality of service has much dimensions, and is considered while it is important that understand quality of service of sea transport industry through marketing and research of customer connection field because perceive of quality of serviceis different in shipowner/service viscount or shipper/freight owner. This research presented decision factors of sea transport quality of service which shipper and transport agent recognize under these background.

• Journal of the Korea Safety Management & Science
• /
• v.9 no.3
• /
• pp.165-171
• /
• 2007

Dependent models in quality statistics are classified as serially autocorrelated model, multivariate model and dependent sample model. Dependent sample model is most efficient in time and cost to obtain samples among the above models. This paper proposes to implement parametric and nonparametric models into production system depended on demand pattern. Nonparametric models have distribution free and asymptotic distribution free techniques. Quality statistical models are classified into two categories ; the number of dependent sample and the type of data. The type of data consists of nominal, ordinal, interval and ratio data. The number of dependent sample divides into 2 samples and more than 3 samples.

• Journal of Industrial Technology
• /
• v.24 no.B
• /
• pp.73-81
• /
• 2004

The development of efficient and precise handling of an liquid crystal display (LCD) panel has been addressed as the sizes of LCD panels become much larger than ever. The majority part of LCD panel handling is conducted by industrial robots for the cost reduction and the quality control. A challenging problem, vibration of the panel, can be found when the robots are utilized for handling LCD panels. The vibration causes the poor product precision and the low productivity. The characteristics of LCD panels, which are the high size-to thickness ratio, the high elasticity, and the high brittleness, are the major sources of the vibration This paper introduces the vibration attenuation techniques to overcome the difficulties encountered in the LCD production using the industrial robots.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.4
• /
• pp.373-379
• /
• 2009

Presented in this paper is a new experimental technique to measure material properties of lock plate of gas turbine plants by using ultrasonic guided wave. In comparison with the mechanical destructive testings, material characterization of the Inconel x-750 was nondestructively carried out in a more efficient manner to discriminate the change in elastic moduli and the poisson's ratio attributed to the variation of heat treatment condition. The proposed technique shows a satisfactory feasibility via the comparative experiments with the imported lock plate specimens. It is also expected that the guided wave technique can cover a longer and wider range as a new cost-&-time-saving inspection tool due to the interaction with a greater part of specimen, compared to a conventional local point-by-point scheme.