• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.4
• /
• pp.823-832
• /
• 2011

In this paper, an efficient blind carrier frequency offset (CFO) estimation method in orthogonal frequency division multiplexing (OFDM) systems is proposed. In the proposed method, we obtain two time different received OFDM symbols by using both the cyclic prefix and oversampling technique, and a cost function is defined by using the two OFDM symbols. We show that the cost function can be approximately expressed as a cosine function. Using a property of the cosine function, a formular for estimating the CFO is derived. The estimator of the CFO requires three independent cost function values calculated at three different points of frequency offset. The proposed method is very efficient in computational complexity since no searching operation for the minimum cost value is required. The proposed method reduces 97% of the amount of FFT computation, compared with the ML method. Unlike the conventional methods such as the ML method and the MUSIC] method, the accuracy of the proposed method is independent of the searching resolution since the closed form solution exists. The computer simulation shows that the performance of the proposed method is superior to those of the MUSIC and the ML method.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.11
• /
• pp.2108-2113
• /
• 2010

The Long Term Evolution (LTE) system is based on the Orthogonal Frequency Division Multiplexing (OFDM) and relies its channel estimation on the lattice-type pilot samples in the multipath fading channel environment. The estimation of the channel frequency response (CFR) makes use of the least squares estimate (LSE) for each pilot samples, followed by an interpolation both in time- and in frequency-domain to fill up the channel estimates for subcarriers corresponding to data samples. Any interpolation scheme could be adopted for this purpose. Depending on the requirements of the target system, we may choose a simple linear interpolation or a sophisticated one. For any choice of an interpolation scheme, these is a trade-off between estimation accuracy and numerical cost. For those wireless communication systems based on the OFDM and the preamble-type pilot structure, the DFT-based channel estimation and its variants have been successfully. Yet, it may not be suitable for the lattice-type pilot structure, since the pilot samples are not sufficient to provide an accurate estimate and it is known to be sensitive to the location as well as the length of the time-domain window. In this paper, we propose a simple interpolated based on the upsampling mechanism in the multirate signal processing. The proposed method provides an excellent alternative to the DFT-based methods in terms of numerical cost and accuracy. The performance of the proposed technique is verified on a multipath environment suggested on a 3GPP LTE specification.

• Transactions of the Korean hydrogen and new energy society
• /
• v.29 no.4
• /
• pp.307-316
• /
• 2018

In this study, the failure mode and effect analysis (FMEA) of hydrogen production process by using the Thermococcus onnurineus NA1 was conducted and advanced methodology to compensate the weakness of previous FMEA methodology was applied. To bring out more quantitative and precise FMEA result for bio-hydrogen production process, fuzzy logic and potential loss cost estimated from ASPEN Capital Cost Estimator (ACCE) was introduced. Consequently, risk for releasing the flammable gases via internal leakage of steam tube which to control the operating temperature of main reactor was caution status in FMEA result without applying the fuzzification and ACCE. Moreover, probability of the steam tube plugging caused by solid property like medium was still caution status. As to apply the fuzzy logic and potential loss cost estimated from ACCE, a couple of caution status was unexpectedly upgraded to high dangerous status since the potential loss cost of steam tube for main reactor and decrease in product gases are higher than expected.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2004.11a
• /
• pp.210-215
• /
• 2004

In can occur to many problems on progressing step without close scope definition, interrelation definition between activities, resource plan, and schedule plan on planning step. But it have not closely defined performance system on planning step because of many constraints of domestic construction industry. Therefore this paper intends to discuss a method of calculating optimal cost and duration using Linear Programming that solves maximing or minimizing problems among decision making methodology and Monte Carlo Simulation that decreases to probability errors. With outcoms applying Linear programming and Monte Carlo Simulation for calculating optimal cost and duration, follow as : With outcomes applying Monte Carlo Simulation, it could calculate reliable estimator about project duration through removing various constraints. With outcomes applying Linear programming, it could calculate optimal value about project cost through defining various variables and constraints on many activities.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.15-22
• /
• 2006

This paper presents a novel signal tracking algorithm for GNSS receivers using a MLE technique. In order to perform a robust signal tracking in severe signal environments, e.g., high dynamics for navigation vehicles or weak signals for indoor positioning, the MLE based signal tracking approach is adopted in the paper. With assuming white Gaussian additive noise, the cost function of MLE is expanded to the cost function of NLSE. Efficient and practical approach for Doppler frequency tracking by the MLE is derived based on the assumption of code-free signals, i.e., the cost function of the MLE for carrier Doppler tracking is used to derive a discriminator function to create error signals from incoming and reference signals. The use of the MLE method for carrier tracking makes it possible to generalize the MLE equation for arbitrary codes and modulation schemes. This is ideally suited for various GNSS signals with same structure of tracking module. This paper proposes two different types of MLE based tracking method, i.e., an iterative batch processing method and a non-iterative feed-forward processing method. The first method is derived without any limitation on time consumption, while the second method is proposed for a time limited case by using a 1st derivative of cost function, which is proportional to error signal from discriminators of conventional tracking methods. The second method can be implemented by a block diagram approach for tracking carrier phase, Doppler frequency and code phase with assuming no correlation of signal parameters. Finally, a state space form of FLL/PLL/DLL is adopted to the designed MLE based tracking algorithm for reducing noise on the estimated signal parameters.

• Journal of the Korean Data and Information Science Society
• /
• v.28 no.5
• /
• pp.1191-1204
• /
• 2017

Weighted least squares (WLS) estimation is often easily used for the data with heteroscedastic errors because it is intuitive and computationally inexpensive. However, WLS estimator is less robust to a few outliers and sometimes it may be inefficient. In order to overcome robustness problems, Box-Cox transformation, Huber's M estimation, bisquare estimation, and Yohai's MM estimation have been proposed. Also, more efficient estimations than WLS have been suggested such as Bayesian methods (Cepeda and Achcar, 2009) and semiparametric methods (Kim and Ma, 2012) in heteroscedastic error models. Recently, Çelik (2015) proposed the weight methods applicable to the heteroscedasticity patterns including butterfly-distributed residuals and megaphone-shaped residuals. In this paper, we review heteroscedastic regression estimators related to robust or efficient estimation and describe their properties. Also, we analyze cost data of U.S. Electricity Producers in 1955 using the methods discussed in the paper.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.406-410
• /
• 1991

This paper presents an improved algorithm of optimal measurement system design with a reliability evaluation method for large power system. The proposed algorithm is developed to consider the dummy bus and to achieve highest accuracy of the state estimator as well with the limited Investment cost. The dummy bus in the power system is impossible to install measurement meter, while real and reactive power measurement values are exactly zero. Thus, the effect on these dummy bus measurements is considered in the proposed algorithm. On the other hand, P/C model is developed by taking advantage of the matrix sparsity. The improved program is successfully tested for KEPCO system with PSS/E lineflow calculated data package.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.228-231
• /
• 2000

When the vector control which does not need a speed signal from a mechanical speed sensor it is possible to reduce the cost of the control equipment and to improve the control performance in many industrial application. In this paper describes a rotor speed estimate method of induction motor based on the theory of counter EMF MRAS. This method eliminated the pure integrator. and we can be expected to rapid responsibility of the speed identification, Therefore we improve the initial condition of the integrator and drift problem. The stability of speed estimator is proved on the basis of hyperstability theory. In order to confirm the performance of the proposed system Simulation and experiment is performed.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.2
• /
• pp.107-117
• /
• 1992

This paper presents an improved algorithm of optimal measurement design with a reliability evaluation method for a large power system. The proposed algorithm is developed to consider the dummy bus and to achieve highest accuracy of the state estimator as well with the limited investment cost. The dummy bus in the power system is impossible to install measurement meter, while real and reactive power measurements is considered in the proposed algorithm. On the other hand, P/C model is developed by taking advantage of the matrix sparsity. The improved program is successfully tested for KEPCO system with PSS/E lineflow calculated data package.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.4 no.2
• /
• pp.63-68
• /
• 2009

The location of mobile terminals in cellular networks is an important problem in the field of information technology with applications in resource allocation, location sensitive browsing, and emergency communications. Finding location estimation techniques that are robust to non-line of light (NLOS) propagation is a key problem in this area. Time of arrival (TOA) and pattern matching (PM) measurements can be made simultaneously by CDMA cellular networks at low cost. The different sources of errors for each measurement type cause TOA and PM measurements to contain independent information about mobile station (MS) locations. This paper combines the information of PM and TOA measurements to calculate a superior location estimate. The proposed location estimator is robust, provides lower error than the estimators based on the individual measurements, and has low implementation costs.