• 한국항공우주학회지
• /
• 제33권9호
• /
• pp.48-55
• /
• 2005

본 논문에서는 비등방성 멤브레인의 주름 거동을 조사하였다. 해석시 멤브레인에 발생하는 주름은 벌칙매개변수법을 사용하여 물성치를 수정하는 방법으로 하였으며, ABAQUS 내 사용자 서브루틴으로 구현하였다. 모서리에 인장하중이 걸린 사각형 멤브레인 문제에 적용하여 주름 거동을 해석한 결과, 핀의 지름이 미치는 영향은 매우 작으며, 잘라낸 모서리의 길이와 전단계수의 크기에 상당한 영향을 받고 있음을 알 수 있었다.

• Wind and Structures
• /
• 제1권4호
• /
• pp.351-364
• /
• 1998

In wind tunnel experiments, the blockage effect is a very important factor which affects the test results significantly. A number of investigations into this problem, especially on the blockage correction of drag coefficient, have been carried out in the past. However, only a limited number of works have been reported on the wind tunnel blockage effect on wind-induced vibration although it is considered to be fairly important. This paper discusses the aerodynamic characteristics of the square model and square model with corner cut based on a series of the wind tunnel tests with various blockage ratios and angles of attack. From the test results, the aerodynamic behavior of square models with up to 10% blockage ratio are almost the same and square models with up to 10% blockage ratio can be tested as a group which behaves similarly.

• 한국강구조학회 논문집
• /
• 제13권3호
• /
• pp.301-311
• /
• 2001

내풍설계에 있어서, 아스펙트비가 6정도인 초고층 건물의 각주형 단면의 바람에 의한 공력 불안정 진동 또는 갤로핑 진동이 발생할 수 있다. 본 연구에서는 등류에서 아스펙트비 6정도이고 변장비가 1/4간격으로 1에서 2까지의 초고층 건물의 각주형 단면에대한 공력불안정 진동과 갤로핑 진동에 대해 실험적으로 고찰하였다. 실험 결과, 등류시 코너 컷이 없는 경우가 코너 컷을 가진 초고층 건물의 각주형 단면에 비해 공력 불안정 진동이 커지는 경향이 있으며, 또한 갤로핑 진동도 나타났다. 따라서, 코너 컷에 의해 각주형 초고층 건물에서의 공력 불안정 진동은 효과적으로 저감되었다.

• 한국정밀공학회지
• /
• 제21권4호
• /
• pp.39-47
• /
• 2004

In mold machining, there are many concave machining regions where chatter and tool deflection occur since MRR(material removal rate) increases as curvature increases even though cutting speed and depth of cut are constant. Boolean operation between stock and tool model is widely used to compute MRR in NC milling simulation. In finish cutting, the side step is reduced to about 0.3mm and tool path length is sometimes over loom, so Boolean operation takes long computation time and includes much error if the resolution of stock and tool model is larger than the side step. In this paper, curvature of CL (cutter location) surface and side step of tool path is used to compute the feedrate for constant MRR machining. The data structure of CL surface is Z-map generated from NC tool path. The algorithm to get local curvature from discrete data was developed and applied to compute local curvature of CL surface. The side step of tool path was computed by point density map which includes cutter location point density at each grid element. The feedrate computed from curvature and side step is inserted to new tool path to regulate MRR. The resultants were applied to feedrate optimization system which generates new tool path with feedrate from NC codes for finish cutting. The system was applied to the machining of speaker and cellular phone mold. The finishing time was reduced to 12.6%, tool wear was reduced from 2mm to 1.1mm and chatter marks and over cut on corner were reduced, compared to the machining by constant feedrate. The machining time was shorter to 17% and surface quality and tool was also better than the conventional federate regulation using curvature of the tool path.

• 한국제4기학회지
• /
• 제17권2호
• /
• pp.139-144
• /
• 2003

The purpose of this study is to identify the species and to date the woods used in the Keunjung-jeon Hall, main building of the Kyungbok palace in Seoul. Samples (144) were divided into two parts, pillars (52) and other wood materials (92). Only two species were identified. They were Abies holophylla Max. and Pinus densiflora Sieb. et Zucc.Eleven among 20 Pyungju (outer pillars) were Abies holophylla, and 9 were Pinus densiflora. Seven among 12 Naejinkoju (inner pillars) were Abies holophylla, and 5 were Pinus densiflora. Three among 4 Gwikoju (inner corner pillars) were Abies holophylla, and one was Pinus densiflora. In the other wood materials, only 2 of 92 were Abies holophylla, and the others were Pinus densiflora. Tree-ring dating proved that this building was reconstructed during late 1860s. It also revealed that the old woods cut in the 17th century were reused.

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2009년도 정보통신설비 학술대회
• /
• pp.289-292
• /
• 2009

In this paper, an optimum design center frequency proposes portable RFID reader antenna that is 920MHz frequency using the Taguchi's Method. Proposed antenna is cut corner of opposite angle and it's structure that have slots in four sides microstrip patch of a perfect square shape. This slot structure can miniaturize microstrip patch antenna and confirmed through an experiment that size of antenna about 18% decreases than structure that slot does not exist. Because compact antenna that have structure of slot changes according to complex design variables, analysis and experimental design for minimization of experiment number of times are required for optimum antenna design. In this research, designed antenna that have optimum structure when introduce and designs table of orthogonal arrays of the Taguchi's Method been experimental design that can minimize analysis and experiment number of times, achieve responsiveness analysis of main elements and analyzes the effect and minimizes design repeat with analysis result. Presented experiment result about antenna special quality that permittivity is 4.4 and manufactures to board of Epoxy 3.2T.

• 열처리공학회지
• /
• 제34권4호
• /
• pp.185-190
• /
• 2021

The extrusion experiments using the 7075 aluminum billet have been performed to investigate the effects of die cooling and ram speed on the occurrence of surface defects on the extrudate. The purpose of die cooling was to suppress overheating of the extrudate at the moment of extrusion. In the present die cooling system, liquid nitrogen has been injected in to the die and sprayed to the surface of extrudate. Ram speed was either kept or varied in the range of 1.1~1.7 mm/sec. throughout one extrusion shot to check the occurrence of surface defects. Every extrusion started at a ram speed of 1.25 mm/sec. The temperature of extrudate was measured using a laser thermometer. The 7075 billet of 180 mm in diameter and 550 mm in length was preheated at 390℃ and extruded to get a single plate of 8000 mm in length, 150 mm in width and 10 mm in thickness. Each extrudate was checked by eye to find the surface defects. The microstructures were obtained in the specimen cut from each corner of the extrudate using the EBSD micrographs.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.235-243
• /
• 2002

Ni-base superalloys are used extensively in industry, both in aeroengines and land based turbines. About 60% by weight of most modern gas turbine engine structural components are made of Ni-base superalloys. To satisfy practical demands, the efficiency of gas turbine engines has been steadily and systematically increased by design modifications to handle higher turbine inlet or firing temperatures. However, the increase in operating temperatures has lead to a decrease in the life of components and increase in costs of replacement. Moreover, around 80% of the large frame size industrial/utility gas turbines operating in the world today were installed in the mid-sixties to early seventies and are now 25 to 30 years old. Consequently, there are greater opportunities now to repair and refurbish the older models. Basically, there are two major factors influencing the weldability of the cast alloys: strain-age cracking and liquation cracking. Susceptibility to strain-age cracking is due to the total Ti plus AI content of the alloy; Liquation cracking is due either to the presence of low melting constituents or constitutional liquation of constituents. Though Rene 41 superalloy has 4.5wt.% total Ti and Al content and falls just below the safe limit proposed by Prager et al., controlled grain size and special heat treatments are needed to obtain crack-free welds. Varying heat treatments and filler materials were used in a laboratory study, then the actual welding of service parts was carried out to verity the possibility of crack-tree weld of components fabricated from Rene 41 superalloy. The microstructural observations indicated that there were two kinds of carbides in the FCC matrix. MC carbides were located along the grain boundaries, while M$_{23}$C$_{6}$ carbide was located both inter and intra granularly. Two kinds of filler materials, Rene 41 and Hastelloy X were used to gas tungsten arc weld a patch into the sheet metal, along with varying pre-weld heat treatments. The microstructure, hardness and tensile tests were determined. The service distressed parts were categorized into three classes: with large cracks, with medium cracks and with small or no visible cracks. No significant difference in microstructure among the specimens was observed. Specimens were cut from the corner and the straight edge of the patch repair, away from the corner. The only cracks present were found to be associated with inadequate surface preparation to remove oxidation. Guidelines for oxide removal and the welding procedures developed in the research enabled crack-free welds to be produced.d.

• Journal of Welding and Joining
• /
• 제24권4호
• /
• pp.32-38
• /
• 2006

The objective of present research works is to investigate the effects of process parameters, including the power of laser, cutting speed, material thickness, and the edge angle, on the melted area in the sharp edge of the cut material fur the case of cutting of a low carbon steel sheet using high-power CW Nd:YAG laser. In order to investigate the influence of edge angle and size of loop on the melted area in the sharp edge, angular cutting tests and loop cutting tests have been carried out. From the results of angular cutting tests, the relationship between the edge angle and the melted area has been obtained. The results of the experiments have been shown that the melted area is rapidly reduced from $120^{\circ}$ of the edge angle and the melted area is nearly zero at $150^{\circ}$ of the edge angle. Through the results of loop cutting experiments, the relationship between the cutting angle on the melted area in the edge according to the size of loop have been obtained. In addition, it has been shown that a proper size of loop is nearly 3 mm as the corner angle is greater than $90^{\circ}$ and 5 mm as the comer angle is less than $90^{\circ}$. The results of above experiments will be reflected on the knowledge base to generate optimal cutting path of the laser.

• 한국지진공학회논문집
• /
• 제24권5호
• /
• pp.219-232
• /
• 2020

The slip-weakening model developed by Ohnaka and Yamashita is extended over the breakdown zone by equating the scaling relationships for the breakdown zone and the whole rupture area. For the extension, the study uses the relationship between rupture velocity and radiation efficiency, which was derived in the theory of linear elastic fracture mechanics, and the definition of f_max given in the specific barrier model proposed by Papageorgiou and Aki. The results clearly show that the extended scaling relationship is governed by the ratio of rupture velocity to S wave velocity, and the velocity ratio can be determined by the ratio of characteristic frequencies of a Fourier amplitude spectrum, which are corner frequency, f_c, and source-controlled cut-off frequency, f_max, or vice versa. The derived relationship is tested by using the characteristic frequencies extracted from previous studies of more than 130 shallow crustal events (focal depth less than 25 km, M_W 3.0~7.5) that occurred in Japan. Under the assumption of a dynamic similarity, the rupture velocity estimated from f_max/f_c and the modified integral timescale give quite similar scale-dependence of the rupture area to that given by Kanamori and Anderson. Also, the results for large earthquakes show good agreement to the values from a kinematic inversion in previous studies. The test results also indicate the unavailability of the spectral self-similarity proposed by Aki because of the scale-dependent rupture velocity and the rupture velocity-dependent f_max/f_c; however, the results do support the local similarity asserted by Ohnaka. It is also remarkable that the relationship between the rupture velocity and f_max/f_c is quite similar to Kolmogorov's hypothesis on a similarity in the theory of isotropic turbulence.