• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.126-131
• /
• 2004

The popularity of flat-panel display(FPD), including plasma display panel(PDP) and liquid-crystal display(LCD), has given rise to the need to streamline their production. In these days, PDP is one of the most popular display devices because of its expansion of manufacturing process and simplicity. Bus electrodes, sustain electrodes, barrier ribs and RGB phosphors are patterned on PDP panel to display an image. Since a minute damage on the pattern can cause a serious defect to display, it is important to inspect the pattern precisely. In this paper, an automatic inspection system of repeated pattern in PDP panel has been introduced to find the defect, such as open, short, dirt, island, and so on. And the inspection system has been operated in the mass production line of PDP.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.6
• /
• pp.71-79
• /
• 2008

In the manufacture of flat panel display devices, there is a strong demand for contactless glass panel handling devices that can manipulate a glass panel without contaminating or damaging it. To fulfill this requirement, an electrostatic suspension device far glass panels where the glass panel is supported by electrostatic forces without any mechanical contact is proposed. To implement the system with low cost and compactness, switched-voltage control scheme that is based on the relay feedback control is utilized. Relay feedback control method deploys only a single high-voltage power supply that can deliver a DC voltage of positive and/or negative polarity and thus high voltage amplifiers that are costly and bulky are not needed any more. It is shown that despite the inherent limit cycle property of the relay feedback based control, an excellent performance in vibration suppression is attained due to the presence of a relatively large squeeze film damping originating from the electrodes and levitated object. Using this scheme, a $100{\times}100mm^2$ glass panel was levitated stably with airgap variation decreasing down to $1\;{\mu}m$ at an airgap of $100\;{\mu}m$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.143-146
• /
• 2008

Dynamic range of LCD panel can be dramatically improved by adaptive dimming technique. Adaptive control of LED backlight by input signal can reduce the light leakage of LCD panel and achieve high contrast ratio. An algorithm is proposed to distinguish the input signal and get proper luminance level. For lower cost of LCD panel, white light LED is used to accomplish 2D dimming and get better image performance of LCD.

• Proceedings of the KIEE Conference
• /
• 1998.11b
• /
• pp.621-623
• /
• 1998

We implemented PanelLlnk digital flat panel display transmitter supporting SXGA($1280{\times}1024$) resolution. It can transmit data through 10m cable at XGA($1024{\times}768$) resolution and through 7m cable at SXGA($1280{\times}1024$). We also found resistor value to get stable display image by low voltage differential signal swing control.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1293-1296
• /
• 2008

As Flat Panel Display become large in format, the data and gate lines turn into longer, parasitic capacitance and resistance increase, and the display signal is delayed. Three dimensional architecture of multiplexing data registration integrated circuit method is used that divides the data line into several blocks and provides the advantages of high accuracy, rapid selection, and reasonable switching speed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.629-632
• /
• 2009

We have proposed a novel viewing angle controllable display of in-plane switching (IPS) mode with single panel. One pixel of this device is divided to two regions, in which main pixel shows image and sub pixel for viewing angle control. In initial state, the liquid crystal of sub pixel is homogeneous aligned on substrate for wide viewing angle mode. On the other hand, after applying voltage, the liquid crystal of sub pixel tilts up for narrow viewing angle mode. The proposed device has advantage for the function for simple manufacturing process and good viewing angle control with single panel.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.939-942
• /
• 2004

In this study, we report simulation results of single-panel LCOS (liquid crystal on silicon). Reflective LCOS microdisplays are widely used in various projection and near-eye application. For one panel system, liquid crystal response time is an important variable. The panel must switch fast enough to support the display of Field color sequential with high field rates. In order to have fast response and good contrast, a vertical alignment (VA) cell was used in this study. With suitable selection on LC parameters like temperature, viscosity, elastic constant and birefringence, it is possible to get response time of around 2ms from a 2.0 um-thick vertical alignment cell. This result also indicates an ease of production control on 2.0 um cells than 1.0 um cells.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.6
• /
• pp.267-273
• /
• 2003

The plasma display panel with the electrode structure of new discharge AND gate and its driving scheme were proposed and the driving system for experiment was developed. And operation of these discharge AND gate was verified by the experiment of PDP addressing with floating electrode. This discharge AND gate operated by the operation speed of 8$mutextrm{s}$ and the operation margin of 100V. The address operation margin of 10V also obtained. It was known to be able to control the discharge of the adjoining scan electrode accurately. Because proposed method uses the DC discharge the control of the discharge can be facilitated compared with conventional discharge AND gate. Moreover, because the input discharge and the output discharge of discharge gate are separate, the display discharge can be prevented from passing discharge gates. Therefore, it is possible to apply to the large screen plasma display panel. And the decrease of contrast ratio does not occur because the scanning discharge does not influence the picture quality.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1236-1239
• /
• 2009

Each LCD TFT panel requires a power supply IC on the panel board. The IC provides the power rails for the timing controller, source and gated driver IC and others. The industry trend moves towards higher integrated devices. The challenge for the panel manufacturer is the development and implementation of such an IC in cooperation with the semiconductor supplier. If not done carefully the solution will not reduce the overall solution cost or can't provide the expected performance and reliability. This paper discusses the key considerations to successfully develop and integrate a highly integrated LCD bias IC into the system.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.402-403
• /
• 2009

A variety of power reduction technologies is introduced and the benefits of the technologies are discussed. PenTile$^{(R)}$ DBLC (Dynamic Brightness LED Control) combined with SABC (Sensor-Based Adaptive Brightness Control) enables to achieve the average LED power consumption to one third. The panel power reduction of 25% can be achieved with low power driving technology, ALS (Active Level Shifter). MIP (Memory In Pixel) is expected to be useful in transflective display because the whole display area can be utilized in reflective mode with power consumption of 1mW.