• 한국기계가공학회지
• /
• 제21권5호
• /
• pp.1-8
• /
• 2022

Fused deposition modeling (FDM), based on stacking a continuous filament of polymer or composite materials, is well matured and is thus widely used in additive manufacturing technology. To advance FDM-based 3D printing technology, the mechanical properties of additively manufactured composite materials must be improved. In this study, we proposed a novel FDM 3D printing process using metal wire-polymer composites, enabling enhanced mechanical properties. In addition, we developed a new type FDM filament of copper wire wrapped in nylon material for stable 3D printing without thermal damage during the printing process. After FDM printing of the copper wire-nylon composite filament, we conducted a tensile test to investigate the mechanical behavior of the printed composite materials. The experimental results confirmed that the tensile strength of the 3D-printed metal wire-polymer composites was higher than that of the conventional single polymer material. Thus, we expect that the FDM printing process developed in this study may be promising for high-load-bearing applications.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.456-456
• /
• 2009

Boron doping on an n-type Si wafer is requisite process for IBC (Interdigitated Back Contact) solar cells. Fiber laser annealing is one of boron doping methods. For the boron doping, uniformly coated or deposited film is highly required. Plasma enhanced chemical vapor deposition (PECVD) method provides a uniform dopant film or layer which can facilitate doping. Because amorphous silicon layer absorption range for the wavelength of fiber laser does not match well for the direct annealing. In this study, to enhance thermal affection on the existing p-a-Si:H layer, a ${\mu}c$-Si:H intrinsic layer was deposited on the p-a-Si:H layer additionally by PECVD. To improve heat transfer rate to the amorphous silicon layer, and as heating both sides and protecting boron eliminating from the amorphous silicon layer. For p-a-Si:H layer with the ratio of $SiH_4$ : $B_2H_6$ : $H_2$ = 30 : 30 : 120, at $200^{\circ}C$, 50 W, 0.2 Torr for 30 minutes, and for ${\mu}c$-Si:H intrinsic layer, $SiH_4$ : $H_2$ = 10 : 300, at $200^{\circ}C$, 30 W, 0.5 Torr for 60 minutes, 2 cm $\times$ 2 cm size wafers were used. In consequence of comparing the results of lifetime measurement and sheet resistance relation, the laser condition set of 20 ~ 27 % of power, 150 ~ 160 kHz, 20 ~ 50 mm/s of marking speed, and $10\;{\sim}\;50 {\mu}m$ spacing with continuous wave mode of scanner lens showed the correlation between lifetime and sheet resistance as $100\;{\Omega}/sq$ and $11.8\;{\mu}s$ vs. $17\;{\Omega}/sq$ and $8.2\;{\mu}s$. Comparing to the singly deposited p-a-Si:H layer case, the additional ${\mu}c$-Si:H layer for doping resulted in no trade-offs, but showed slight improvement of both lifetime and sheet resistance, however sheet resistance might be confined by the additional intrinsic layer. This might come from the ineffective crystallization of amorphous silicon layer. For the additional layer case, lifetime and sheet resistance were measured as $84.8\;{\Omega}/sq$ and $11.09\;{\mu}s$ vs. $79.8\;{\Omega}/sq$ and $11.93\;{\mu}s$. The co-existence of $n^+$layeronthesamesurfaceandeliminating the laser damage should be taken into account for an IBC solar cell structure. Heavily doped uniform boron layer by fiber laser brings not only basic and essential conditions for the beginning step of IBC solar cell fabrication processes, but also the controllable doping concentration and depth that can be established according to the deposition conditions of layers.

• 한국진공학회지
• /
• 제21권3호
• /
• pp.178-184
• /
• 2012

니켈촉매 막을 증착시킨 산화규산 기판 위에 아세틸렌기체와 수소기체를 원료기체로 육불화황기체를 첨가기체로 사용하여 열화학기상증착 방법으로 탄소코일을 합성하였다. 첨가기체의 유량과 아세틸렌/육불화황 기체들의 싸이클릭 on/off 유량 변조에 따라 성장된 탄소코일의 특성(형성 밀도, 형상)을 조사하였다. 육불화황의 기체 유량이 가장 낮은 경우(5 sccm)에서, 2분동안 육불화황을 주입하여 아세틸렌/육불화황 기체를 싸이클릭 on/off 유량 변조시킴에 따라 탄소코일을 형성시켰다. 반면 육불화황을 5분 동안 연속적으로 주입한 경우에서는 탄소나노필라멘트 형상이 나타나지 않았다. 육불화황의 유량이 5 sccm에서 30 sccm으로 증가함에 따라 아세틸렌/육불화황 기체들의 싸이클릭 on/off 유량 변조는 탄소코일의 형상을 나노크기의 형태로만 제한시켰다. 육불화황 기체의 플로린 종에 의한 에칭 특성이 이러한 효과를 주게 하는 것으로 이해되었다.

• 한국재료학회지
• /
• 제30권4호
• /
• pp.204-210
• /
• 2020

ZnO thin films are of considerable interest because they can be customized by various coating technologies to have high electrical conductivity and high visible light transmittance. Therefore, ZnO thin films can be applied to various optoelectronic device applications such as transparent conducting thin films, solar cells and displays. In this study, ZnO rod and thin films are fabricated using aqueous chemical bath deposition (CBD), which is a low-cost method at low temperatures, and environmentally friendly. To investigate the structural, electrical and optical properties of ZnO for the presence of citrate ion, which can significantly affect crystal form of ZnO, various amounts of the citrate ion are added to the aqueous CBD ZnO reaction bath. As a result, ZnO crystals show a nanorod form without citrate, but a continuous thin film when citrate is above a certain concentration. In addition, as the citrate concentration increases, the electrical conductivity of the ZnO thin films increases, and is almost unchanged above a certain citrate concentration. Cu(In,Ga)Se₂ (CIGS) solar cell substrates are used to evaluate whether aqueous CBD ZnO thin films can be applicable to real devices. The performance of aqueous CBD ZnO thin films shows performance similar to that of a sputter-deposited ZnO:Al thin film as top transparent electrodes of CIGS solar cells.

• 한국해양학회지:바다
• /
• 제3권3호
• /
• pp.149-157
• /
• 1998

우리나라서해안의 곰소만 조간대에서 조간대 퇴적층의 형성 및 보존과정을 규명하기 위해 지형, 퇴적물의 입도, 집적률 등의 계절적 변화를 조사하였다. 조간대를 횡단하는 측선에 대해 계절별로 수준측량한 결과, 겨울과 태풍 때 중부 조간대의 조간대사주(intertidal sand shoal)와 상부 조간대의 쉐니어(chenier)가 육지방향으로 크게 이동하였고, 특히 태풍 때에는 중 하부 조간대가 광범위하게 침식되었다. 그러나 여름에는 조간대사주와 쉐니어의 이동이 제한되었고, 중부 조간대의 상부역과 상부 조간대에 펄이 퇴적되었다. 퇴적물의 계절적 입도변화는 주로 중부 조간대의 상부역에서 크게 나타났으며, 대체로 5.5 ${\phi}$에서 모드를 갖는 펄질 퇴적물의 집적(여름)과 침식(겨울, 태풍)에 의해 야기되었다. 해저면에서 기준면까지의 깊이를 2 개월 간격으로 측정한 결과, 상부 조간대에서는 연중 지속적으로 퇴적이 이루어지고 겨울보다 여름에 집적률이 높은 반면, 중부 조간대에서는 여름보다 겨울에 퇴적이 우세하고 태풍 때 간헐적으로 침식되는 특징을 보였다. 그리고 하부 조간대는 주로 겨울에 퇴적되었고 여름과 태풍 때 침식되었다. 캔코아를 통해 퇴적층의 보존모습을 분석한 결과, 위의 계절변화 양상이 대체로 코아의 상부층에만 제한적으로 보존되었고, 하부층으로 갈수록 폭풍 퇴적층의 출현빈도가 증가하였다. 이상의 결과들에 기초하여 볼 때, 곰소만 조간대층의 많은 부분이 겨울 폭풍 또는 간헐적 태풍에 의해 재구성된 폭풍 퇴적층일 가능성이 높은 것으로 판단된다.

• 한국결정성장학회지
• /
• 제10권1호
• /
• pp.17-22
• /
• 2000

수직보자력이 크고 CoCrPt에 비하여 noise 저감 효과가 큰 것으로 알려진 CoCrPtTa계 합금박막의 수직이방성을 더욱 개선하기 위해 Ti를 우선 증착하였다. 본 연구에서는 Ti 두께 변화에 따른 비교적 높은 수직보자력치를 보였던 $CoCr_{16.2}Pt_{10.8}Ta_4$Ti/glass 시편에서 자기적 특성과 자구형상의 변화를 살펴보았다. 또한 VSM(Vibrating Sample Magnetometer)을 이용하여 M-H loop를 측정하였으며 자구형상은 MFM(Magnetic Force Microscopy)로 관찰하였다. 육방정 Ti가 하지층으로서 우선증착되면 bare glass 직접 증착되는 경우보다 CoCrPtTa 자성층의 수직이방성에 현저한 향상을 가져왔으며 Ti의 두께가 두꺼울수록 c-축 배향성도 개선되었다. MFM 결과에 의하면 Ti두레가 20 nm에서 90 nm로 증가함에 따라 자구형상이 연속적인 stripe type에서 mass type으로 분절된 형태로 변하였다. 이는 Ti의 증착이 비자성 Cr 편석 거동에 영향을 미쳐 자화반전시 인접 columnar grain의 자화벡터들간의 상호교환작용을 억제하는 자기적 분리 효과에 기여했음을 의미한다. 아울러 이와 같은 거동은 Ti가 CoCr계 자성층의 수직이방성을 개선하는데 있어서 형상자기이방성적인 측면에서의 기여가 현저함을 의미하기도 한다.

• The Korean Journal of Physiology and Pharmacology
• /
• 제22권6호
• /
• pp.607-616
• /
• 2018

The effect of melatonin on juveniles with cardio fibrosis is poorly understood. We investigated whether HDACs participate in the anti-fibrotic processes regulated by melatonin during hypertrophic remodeling. Abdominal aortic constriction (AAC) was employed in juvenile rats resulting in pressure overload-induced ventricular hypertrophy and melatonin was subsequently decreased via continuous light exposure for 5 weeks after surgery. AAC rats displayed an increased cross-sectional area of myocardial fibers and significantly elevated collagen deposition compared to sham-operated rats, as measured by HE and Masson Trichrome staining. Continuous light exposure following surgery exacerbated the increase in the cross-sectional area of myocardial fibers. The expression of HDAC1, HDAC2, HDAC3, HDAC4 and HDAC6 genes were all significantly enhanced in AAC rats with light exposure relative to the other rats. Moreover, the protein level of $TNF-{\alpha}$ was also upregulated in the AAC light exposure groups when compared with the sham. However, Smad4 protein expression was unchanged in the juveniles' hearts. In contrast, beginning 5 weeks after the operation, the AAC rats were treated with melatonin (10 mg/kg, intraperitoneal injection every evening) or vehicle 4 weeks, and sham rats were given vehicle. The changes in the histological measures of cardio fibrosis and the gene expressions of HDAC1, HDAC2, HDAC3, HDAC4 and HDAC6 were attenuated by melatonin administration. The results reveal that melatonin plays a role in the development of cardio fibrosis and the expression of HDAC1, HDAC2, HDAC3, HDAC4 and HDAC6 in cardiomyocytes.

• 한국습지학회지
• /
• 제15권3호
• /
• pp.423-430
• /
• 2013

일반적 형태의 해안영역에서의 퇴적물이동, 퇴적 및 지형변화를 예측하는 수치모형에서 전빈의 침식으로 인한 해안선 후퇴가 가능한 알고리즘을 제시한다. 평균해수면 기준의 해안선 인근 영역에서는 저면 경사가 저면 퇴적물의 종류, 조석과 조류, 파랑, 연안류 등 외력의 영향을 받는다. 그러나, 해안선에서의 저면경사는 어느 정도 안정된 범위내의 값을 가지는 것으로 보고된 바 있으며, 연중 변화 또한 거의 일정 범위 내에 있는 것으로 알려져 있다. 이러한 경사의 변동 한계값을 이용하여, 해중 침식이 지속되어 해안선에서의 저면 경사가 계속 증가하는 경우, 이러한 한계 경사를 넘게 되면, 이를 조정하기 위한 방법으로서 저면경사가 한계값 내로 돌아오도록 해안선 인근에서의 저면 형상을 조정하도록 하였다. 이렇게 함으로써 침식이 지속되는 경우 해안선이 지속적으로 후방으로 후퇴하는 현상을 수치모형에서 재현할 수 있게 된다. 개발한 알고리즘을 우물함수형의 침식 상황, 즉 한 점에서 일정 플럭스로 준설을 지속할때 주변 지형이 우물함수 분포 형상으로 침식되어 가는 과정을 잘 재현하였다. 발달하는 해안선의 형태가 거의 원형의 동심원으로 나타나므로 알고리즘의 유용함을 확인하였다. 또 개발한 알고리즘을 침식지역이 일정속도로 하강하는 가상상황에 적용하여 보았으며, 동심원적 지형 변화를 잘 재현하였다. 본 알고리즘을 기존의 수치모형 CST3D 시스템에 채택하여, 등경사 평판형 해안에 이안제가 놓여 있을 경우에 대한 지형변화 수리모형실험의 조건과 동일한 조건을 대상으로 모형실험을 수행한 결과, 해안선의 변화를 정성적으로 만족스럽게 재현하였다.

• Nuclear Engineering and Technology
• /
• 제45권4호
• /
• pp.513-522
• /
• 2013

The ODSCC detected in the TSP position of Ulchin 3&4 SGs are typical ODSCC of Alloy 600MA tubes. The causative chemical environment is formed by concentration of impurities inside the occluded region formed by the tube surface, egg crate strips, and sludge deposit there. Most cracks are detected at or near the line contacts between the tube surface and the egg crate strips. The region of dense crack population, as defined as between $4^{th}$ and $9^{th}$ TSPs, and near the center of hot leg hemisphere plane, coincided well with the region of preferential sludge deposition as defined by thermal hydraulics calculation using SGAP computer code. The cracks developed homogeneously in a wide range of SGs, so that the number of cracks detected each outage increased very rapidly since the first detection in the $8^{th}$ refueling outage. The root cause assessment focused on investigation of the difference in microstructure and manufacturing residual stress in order to reveal the cause of different susceptibilities to ODSCC among identical six units. The manufacturing residual stress as measured by XRD on OD surface and by split tube method indicated that the high residual stress of Alloy 600MA tube played a critical role in developing ODSCC. The level of residual stress showed substantial variations among the six units depending on details of straightening and OD grinding processes. Youngwang 3&4 tubes are less susceptible to ODSCC than U3 and U4 tubes because semi-continuous coarse chromium carbides are formed along the grain boundary of Y3&4 tubes, while there are finer less continuous chromium carbides in U3 and U4. The different carbide morphology is caused by the difference in cooling rate after mill anneal. There is a possibility that high chromium content in the Y3&4 tubes, still within the allowable range of Alloy 600, has made some contribution to the improved resistance to ODSCC. It is anticipated that ODSCC in Y5&6 SGs will be retarded more considerably than U3 SGs since the manufacturing residual stress in Y5&6 tubes is substantially lower than in U3 tubes, while the microstructure is similar with each other.

• Advances in pediatric surgery
• /
• 제4권2호
• /
• pp.125-130
• /
• 1998

To assess the clinical and nutritional status of long-term survivors of biliary atresia, history taking, medical record review, physical examination (height, weight, MAC, TSF), blood tests (LFT, prothrombin time, platelet count, prealbumin, calcium) and liver needle biopsy were performed in 12 patients in whom Kasai procedure were performed more than 10 years ago at Department of Pediatric Surgery in Seoul National University Hospital. None were below the 5th percentile in height and weight. TSF was above the 75th percentile in all patients and showed good subcutaneous fat deposition. MAC was above the 5th percentile in all patients. Serum prealbumin level was abnormal in 2 patients with abnormal liver function and revealed visceral protein malnutrition. Serum calcium level was decreased below normal range in 4 patients with abnormal liver function. One patient had mild ascites. Five patients had abnormal liver function and 7 patients showed clinical manifestation of portal hypertension. Liver needle biopsy was performed in 5 patients and no cirrhotic change was observed. Although some patients who have survived for more than 10 years after Kasai procedure developed protein malnutrition and vitamin deficiencies, growth and development and nutritional status were generally satisfactory. Five patients(42%) showed normal liver function and no portal hypertension. In conclusion, Kasai procedure is satisfactory as a primary treatment in biliary atresia but significant portion of long-term survivors had abnormal liver function and portal hypertension. Continuous and careful follow-up is necessary to determine when liver transplantation may be indicated.