• 대한수학회보
• /
• 제53권4호
• /
• pp.1237-1247
• /
• 2016

The object of the present paper is to characterize $({\kappa}$, ${\mu}$)-contact metric manifolds whose concircular curvature tensor satisfies certain semisymmetry conditions. We also verify that the result holds by a concrete example.

• Kyungpook Mathematical Journal
• /
• 제51권4호
• /
• pp.457-468
• /
• 2011

We consider pseudo-symmetric and Ricci generalized pseudo-symmetric N(${\kappa}$) contact metric manifolds. We also consider N(${\kappa}$)-contact metric manifolds satisfying the condition $S{\cdot}R$ = 0 where R and S denote the curvature tensor and the Ricci tensor respectively. Finally we give some examples.

• Structural Engineering and Mechanics
• /
• 제48권2호
• /
• pp.241-255
• /
• 2013

The receding contact problem for two elastic layers whose elastic constants and heights are different supported by two elastic quarter planes is considered. The lower layer is supported by two elastic quarter planes and the upper elastic layer is subjected to symmetrical distributed load whose heights are 2a on its top surface. It is assumed that the contact between all surfaces is frictionless and the effect of gravity force is neglected. The problem is formulated and solved by using Theory of Elasticity and Integral Transform Technique. The problem is reduced to a system of singular integral equations in which contact pressures are the unknown functions by using integral transform technique and boundary conditions of the problem. Stresses and displacements are expressed depending on the contact pressures using Fourier and Mellin formula technique. The singular integral equation is solved numerically by using Gauss-Jacobi integration formulation. Numerical results are obtained for various dimensionless quantities for the contact pressures and the contact areas are presented in graphics and tables.

• 한국정밀공학회지
• /
• 제27권3호
• /
• pp.80-88
• /
• 2010

A simple computational model for modeling of subsurface crack growth under cyclic contact loading is presented. In this model, it is assumed that the initial fatigue crack will initiate in the region of the maximum equivalent stress at certain depth under the contacting surface. The position and magnitude of the maximum equivalent stress are determined by using the equivalent contact model, which is based on the Hertzian contact conditions with frictional forces. The virtual crack extension method is used for simulation of the fatigue crack growth from the initial crack up to the formation of the surface pit due to contact fatigue. The relationships between the stress intensity factor and crack length are then determined for various combinations of equivalent contact radii and loadings.

• 한국전산구조공학회논문집
• /
• 제13권3호
• /
• pp.305-319
• /
• 2000

본 논문에서는 대변형 비선형 변형체의 마찰 접촉 문제의 해법을 제시하였다. 접촉 가능 점에서 접촉조건을 접촉오차 벡터를 이용하여 표시하였으며, 이러한 접촉오차 벡터를 0으로 단조 감소시키기 위하여 반복계산법을 사용하였다. 각 반복계산은 2개의 단계로 구성되어 있다 : 첫 단계에서는 이미 구해진 해의 기하학적 모양에서 얻어지는 접촉오차 벡터를 이용하여 접촉력을 수정하고, 두 번째 단계에서는 첫 단계의 접촉력을 이용하여 평형방정식을 풀어서 변위 및 접촉오차를 계산하는 것이다. 본 반복계산법에 의하여 정확한 해를 얻을 수 있음을 설명하였으며, 강소성 막 및 비선형 탄성보를 사용하여 예제계산을 수행하였다.

• 대한인간공학회지
• /
• 제29권4호
• /
• pp.639-646
• /
• 2010

The APAM's quantitative effectiveness and comparative study in preventing and treating pressure ulcer has not been sufficiently evaluated mainly because of uncertainty of pressure load input and lack of interpretation of dynamic perfusion recovery characteristics of soft tissue. The purpose of this paper was to quantify and analyze the alternating pressure characteristics of APAM as a preventive measure for pressure ulcers. To quantify the alternating load to human body, we introduced alternating pressure profile concept and developed parametric model of the profile. Regarding pressure level and cycle time, 3 global and 7 local periodic parameters were used to define the profile such as light, standard, typical and heavy duty profile shape. Pressure impulse ratio of light duty is the lowest but pressure fluctuation is significantly high. For the same duty shape, contact conditions are changed with alternating cycle time and more dramatically in shorter alternating cycle time conditions. We can conclude that if we use shorter alternating cycle time on APAM's operation we can get more positive effects regarding to inflated contact time condition. We proposed the quantitative methods on tissue viability study of external loading by simultaneous measurement of interface pressure and tissue perfusion with proper alternating pressure profile conditions.

• Nuclear Engineering and Technology
• /
• 제45권1호
• /
• pp.53-60
• /
• 2013

Bentonite is generally used as a buffer material in high-level radioactive waste disposal facilities and consists of 50% quartz by weight. Quartz strongly affects the behavior of bentonite over very long periods. For this reason, quartz dissolution experiment was performed under high-pressure and high-alkalinity conditions based on the conditions found in a high-level radioactive waste disposal facility located deep underground. In this study, two quartz dissolution experiments were conducted on 1) quartz beads under low-pressure and high-alkalinity conditions and 2) a single quartz crystal under high-pressure and high-alkalinity conditions. Following the experiments, a confocal laser scanning microscope (CLSM) was used to observe the surfaces of experimental samples. Numerical analyses using the finite element method (FEM) were also performed to quantify the deformation of contact area. Quartz dissolution was observed in both experiments. This deformation was due to a concentrated compressive stress field, as indicated by the quartz deformation of the contact area through the FEM analysis. According to the numerical results, a high compressive stress field acted upon the neighboring contact area, which showed a rapid dissolution rate compared to other areas of the sample.

• PNF and Movement
• /
• 제22권1호
• /
• pp.91-99
• /
• 2024

Purpose: Backward walking has shown positive effects on gait recovery in rehabilitation patients. It is increasingly used as an aerobic training method in rehabilitation populations, inducing more sensory and motor stimulation than forward walking. Therefore, the purpose of this study is to investigate the effects of visual stimulation during backward walking. Methods: Twenty-seven healthy adults with a visual acuity of 0.8 or higher participated in the study. To compare the effects of visual stimulation during various walking conditions among healthy individuals, the participants randomly selected cards numbered one to six and walked a distance of 10 meters. Walking ability was measured using Optogait. Results: Statistically significant differences were observed in speed, stride, and percentages of single support and contact phase during backward walking. Within eyes-closed conditions during backward walking, significant differences were found in percentages of single support, terminal stance, and contact phase. Moreover, the percentage of terminal swing significantly differed during backward walking with head turn conditions. Conclusion: Gait parameters such as speed, stride, and percentages of single support and contact phase were higher during backward walking than forward walking. These results indicate that backward walking involves multiple sensory systems and varying conditions.

• 전기학회논문지
• /
• 제62권4호
• /
• pp.573-576
• /
• 2013

In this paper, analysis method for current collection performance based on real-time current of catenary system is proposed. An innovative method based on track-side of railway system is used for measurement of currents for overhead contact line during the collection with pantograph. The evaluation of a qualitative ratio for current collection performance were conducted using proposed algorithm under various conditions such as laboratory and track-side. To check the validity of our approach, we compared between calculation results from current of contact wire and measurement results from arcing of pantograph using simulator in laboratory conditions. The results show that the behavior of current collection performance were analysis from currents of overhead contact line in AC electric railway system.

• 소성∙가공
• /
• 제18권7호
• /
• pp.565-571
• /
• 2009

This paper is concerned with the analysis on the surface stress profiles of perfectly plastic material in backward extrusion process. Due to heavy surface expansion appeared usually in the backward extrusion process, the tribological conditions along the interface between the material and the punch land are very severe. In the present study, the analyses have focused to reveal the surface conditions at the contact boundary for various punch shapes in terms of surface expansion, contact pressure, and relative movement between punch and workpiece which consists of sliding velocity and distance, respectively. Punch geometries adopted in the analysis include concave, hemispherical, pointed and ICFG recommended shapes. Extensive simulation has been conducted by applying the rigid-plastic finite element method to the backward extrusion process under different punch geometries. The simulation results are summarized in terms of surface expansion, contact pressure, sliding velocity and sliding distance at different reduction in height, deformation patterns, and load-stroke relationship, respectively.