• The Journal of Korean Academy of Prosthodontics
• /
• v.40 no.1
• /
• pp.1-17
• /
• 2002

The purpose of this study is to examine the possibility of thermal injury to bone tissues during an implant site preparation under the same condition as a typical clinical practice of $Br{\aa}nemark$ implant system. All the burs for $Br{\aa}nemark$ implant system were studied except the round bur The experiments involved 880 drilling cases : 50 cases for each of the 5 steps of NP, 5 steps of RP, and 7 steps of WP, all including srew tap, and 30 cases of 2mm twist drill. For precision drilling, a precision handpiece restraining system was developed (Eungyong Machinery Co., Korea). The system kept the drill parallel to the drilling path and allowed horizontal adjustment of the drill with as little as $1{\mu}m$ increment. The thermocouple insertion hole. that is 0.9mm in diameter and 8mm in depth, was prepared 0.2mm away from the tapping bur the last drilling step. The temperatures due to countersink, pilot drill, and other drills were measured at the surface of the bone, at the depths of 4mm and 8mm respectively. Countersink drilling temperature was measured by attaching the tip of a thermocouple at the rim of the countersink. To assure temperature measurement at the desired depths, 'bent-thermocouples' with their tips of 4 and 8mm bent at $120^{\circ}$ were used. The profiles of temperature variation were recorded continuously at one second interval using a thermometer with memory function (Fluke Co. U.S.A.) and 0.7mm thermocouples (Omega Co., U.S.A.). To simulate typical clinical conditions, 35mm square samples of bovine scapular bone were utilized. The samples were approximately 20mm thick with the cortical thickness on the drilling side ranging from 1 to 2mm. A sample was placed in a container of saline solution so that its lower half is submerged into the solution and the upper half exposed to the room air, which averaged $24.9^{\circ}C$. The temperature of the saline solution was maintained at $36.5^{\circ}C$ using an electric heater (J. O Tech Co., Korea). This experimental condition was similar to that of a patient s opened mouth. The study revealed that a 2mm twist drill required greatest attention. As a guide drill, a twist drill is required to bore through a 'virgin bone,' rather than merely enlarging an already drilled hole as is the case with other drills. This typically generates greater amount of heat. Furthermore, one tends to apply a greater pressure to overcome drilling difficulty, thus producing even greater amount heat. 150 experiments were conducted for 2mm twist drill. For 140 cases, drill pressure of 750g was sufficient, and 10 cases required additional 500 or 100g of drilling pressure. In case of the former. 3 of the 140 cases produced the temperature greater than $47^{\circ}C$, the threshold temperature of degeneration of bone tissue (1983. Eriksson et al.) which is also the reference temperature in this study. In each of the 10 cases requiring extra pressure, the temperature exceeded the reference temperature. More significantly, a surge of heat was observed in each of these cases This observations led to addtional 20 drilling experiments on dense bones. For 10 of these cases, the pressure of 1,250g was applied. For the other 10, 1.750g were applied. In each of these cases, it was also observed that the temperature rose abruptly far above the thresh old temperature of $47^{\circ}C$, sometimes even to 70 or $80^{\circ}C$. It was also observed that the increased drilling pressure influenced the shortening of drilling time more than the rise of drilling temperature. This suggests the desirability of clinically reconsidering application of extra pressures to prevent possible injury to bone tissues. An analysis of these two extra pressure groups of 1,250g and 1,750g revealed that the t-statistics for reduced amount of drilling time due to extra pressure and increased peak temperature due to the same were 10.80 and 2.08 respectively suggesting that drilling time was more influenced than temperature. All the subsequent drillings after the drilling with a 2mm twist drill did not produce excessive heat, i.e. the heat generation is at the same or below the body temperature level. Some of screw tap, pilot, and countersink showed negative correlation coefficients between the generated heat and the drilling time. indicating the more the drilling time, the lower the temperature. The study also revealed that the drilling time was increased as a function of frequency of the use of the drill. Under the drilling pressure of 750g, it was revealed that the drilling time for an old twist drill that has already drilled 40 times was 4.5 times longer than a new drill The measurement was taken for the first 10 drillings of a new drill and 10 drillings of an old drill that has already been used for 40 drillings. 'Test Statistics' of small samples t-test was 3.49, confirming that the used twist drills require longer drilling time than new ones. On the other hand, it was revealed that there was no significant difference in drilling temperature between the new drill and the old twist drill. Finally, the following conclusions were reached from this study : 1 Used drilling bur causes almost no change in drilling temperature but increase in drilling time through 50 drillings under the manufacturer-recommended cooling conditions and the drilling pressure of 750g. 2. The heat that is generated through drilling mattered only in the case of 2mm twist drills, the first drill to be used in bone drilling process for all the other drills there is no significant problem. 3. If the drilling pressure is increased when a 2mm twist drill reaches a dense bone, the temperature rises abruptly even under the manufacturer-recommended cooling conditions. 4. Drilling heat was the highest at the final moment of the drilling process.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.2
• /
• pp.38-45
• /
• 1999

This study was to figure out proper Formaldehyde/Urea molar ratio of UF resin with satisfactory bonding strength of plywood and properties of particleboard. The six kinds of UF resins were manufactured with F/U molar ratio 1.0, 1.2, 1.4, 1.6, 1.8, and 2.0. The boards were made of three kinds of raw materials : Veneer, Sliver-Particle and Strand-Particle. Manufacturing condition of plywood : amount of mixing resin was 150g/$m^2$. The fourty secs/mm simple-pressing schedule in the pressure 10kgf/$m^2$ was applied for 480mm${\times}$700mm board at the temperature of $110^{\circ}C$ in a hot press. Manufacturing condition of particleboard : Target density was 0.65g/$cm^2$. The stepwise 9 minutes- multi-pressing schedule in the maximum pressure 40kgf/$cm^2$, the minimum pressure 15kgf/$cm^2$ was applied for $480mm{\times}634mm{\times}12mm$ board at the temperature of $150^{\circ}C$ in a hot press. The results are as follows : I. In bonding strength, plywood which was made by F/U molar ratio 1.2 showed the highest value. Other molar ratio resin also gave the satisfied value of KS standard, 7.5kgf/$cm^2$. 2. In internal bond strength of particleboard, Sliver-Particleboard(SLPB) and Strand-Particleboard(STPB) varied respectively from 5.9kgf/$cm^2$ to 4.8kgf/$cm^2$, from 6.7kgf/$cm^2$ to 5.4kgf/$cm^2$. SLPB with F/U=1.2 and STPB with F/U=1.6 had higher IB value. Also, both SLPB and STPB showed lower IB value in F/U molar ratio 2.0 and 1.0. 3. SLPB and STPB with six kinds of UF resin respectively satisfied bending strength of KS standard 150 Type(130kgf/$cm^2$) and 200 Type(180kgf/$cm^2$). Bending strength data for both of SLPB and STPB showed little or no loss from F/U=1.8 to F/U=1.2. Also, STPB was approximately two times higher than that of SLPB. Therefore, the raw material's shape had more effect on bending strength than the FlU molar ratio. 4. F/U=1.6 and 1.4 showed the lower thickness swelling in SLPB and STPB. All of STPBs satisfied thickness swelling of KS standard, under 12%.

• Economic and Environmental Geology
• /
• v.40 no.5
• /
• pp.605-622
• /
• 2007

Elemental, Rock-Eval pyrolysis and isotopic analysis of the core sediments from the northwestern and eastern Ulleung Basin of the East were carried out to identify their geochemical characteristics, spatial and vertical variation and origin of organic matter in Upper Quaternary sediments from the northwestern and eastern Ulleung Basin of the East Sea. TOC, m and TS did not show spatial variation between the sampling locations whereas they showed systematic vertical variation associated with MIS stages related to the sea-level change of the East Sea. It is suggested that these past changes of sea-level influenced the sedimentary depositional environments and/or diagenesis which resulted the patterns observed in this study. Based on the results of TOC/N, TS/TOC, ${\delta}^{13}C_{org}\;and\;{\delta}^{15}N_{org}$ analysis, organic matters in the study area appears to be predominantly originated from the marine algae rather than land plant and deposited under normal marine oxic condition during MIS I and MIS III period, and under euxinic/anoxic condition during MIS II period. TOC/N, ${\delta}^{13}C_{org}\;and\;{\delta}^{15}N_{org}$ have a relatively constant value irrespective of MIS stages, implying that the organic matter source does not change by the sea-level fluctuations. However, the results of Rock-Eval pyrolysis indicates that the organic matter is in immature stage and originated from land-plant (Type III), locating in the immature stage land plant (Type III). Similar differences were reported from other areas such as the Atlantic Ocean, Iberia Abyssal Plain, Mediterranean Sea, suggesting that Rock-Eval method does not exactly reflect the characteristic of immature organic matters. Accordingly, the application of Rock-Eval pyrolysis for delineating the source of immature organic matters should be approached with caution and all other geochemical proxies should be considered altogether at the same time.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.15-15
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic?iency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet?ween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr?ease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$$$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea?ses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin?ear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num?ber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco?very rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Sasang Constitution and Immune Medicine
• /
• v.10 no.2
• /
• pp.351-429
• /
• 1998

The Purpose of Study 1. Inspection of clinical application on TCD to CVA 2. Objective Comparement and analysis about treatment effect of Western-Medicine, Korean Medicine, Cooperative consultation of Korean and Western medicice for CVA The Subject of Study We intended for the eighty six patient of CVA who had been treated in the Oriental Medical Hospital at Dong Eui Medical Center from 1997. 8. I to 1998. 7. 31 1. View of CT, MRI : the patient of Cb infarction 2. Attack Time : The patient who coming hospital falling ill within the early one week The method of study 1. Treat four group of Korean medicine, Constitution medicine, Western medicine, cooperative consultation of Korean medicine and Western medicine. 2. Application of TCD Check the result for three times, immediatly after the attack, two months later, four months later 3. Comparative analysis of each treatment effect by clinical symptoms and pathologic examination 4. The Judgement of the patient The Result From 8/1/1997 to 7/31/1998, We have the following result by clinical analysis intended for CVA 86 patients who had been treated in the Oriental Medical Hospital at Dong Eui Medical Center from 1997. 8. 1 to 1998. 7. 31 in 1. Analysis according to Age The first stage of thirties, forties, seventies is heavier than forties, fifties in improvement and Index of improvement of symptom 2. Analysis according to sex We have no special relation in an average of symptom and improvement, Index improvement 3. Analysis according to Family History We have the better result in first stage and improvement, index improvement when no family history. 4. Analysis according to Past History We have no special relation in past history like hypertension, DM, heart problem 5. Analysis devided two group, above group and under group on the basis of the average in first stage of all patient. We have the better result when the first stage is light, that the first score of barthel index and CNS is high. 6. Analysis of the effect of treatment about Korean medical treatment, Western medical treatment, cooperative treatment. In this study, the highest group of rate of treatment at four contrast groups (Korean medicine, Constitution medicine, Western medicine, cooperative treatment according to dyagnosis and range of treatment was the patient group of doing dyagnosis and method of treatment based on constitution medicine theory. This is that of doing demostation, A-Tx, po-herb-medication according to dyagnosis and treat method of constitution of Lee Je-ma In case of left, the case of dyagnosis any disease according to doctor view but, normal in TCDwas 22-beginning of attack, 20- two weeks later, 11 case-four weeks later in case of right, 15-beginning of attack, 12-two weeks later, 9 case four weeks later. So left vessel compares to right vessel is more interference, in fact more than a 1/2 of the patients of MCA disease can't do dyagnosis. In rate of imparement, the state of pacient improved but there isn't the improved case of result in TCD. 7. In TCD dyagnosis, between the case of inconsus the doctor view specially MCA in brain blood vessel is in large numbers and in total 86's patient, impossible case of dyagnosis according to interferiance of temporal is 21 case. 7. Result study about application of Kreaan medical treatment 1) The impossible patient of observation MCA blood vescular for interference temporal bone happened in large numbers. 2) There is the case having difference result to CT,MRI, MRA result. 3) Because individual difference is large, excluding to ananalogy of symptom. This is normal numerical value that has possibility of being checked as abnormal numerical value 4) there are a lot of cases that the speed of normal part is as similarly measured as that of abnormal part. It means that we cannot judge the disease by this measure 5) It is rare that this measure represent degree of improvement in patient's condition of disease. When we observe patient's condition become better, but we have no case that the result of TCD test better. 6) The result could be appear differently by the technique of the tester or by the experience of the tester 7) In the TCD test, abnormal symptoms is checked at 0 week, but at 2th week, normal symptoms is checked, again at 4th week abnormal is checked. According to the above result, CVA diagnosis is difficult only with TCD, as it appear in diagnosis error check which is suggested in the problem connected to project, for the aged persons who have the worst hardening of part of the cranium (1998. 5. 26 77 of 83 patients is 50s) there is a lot of cases that the measurement is impossible by TCD and the correction of measurement numerical value is decreased, as the age of cerebral infarction is high, TCD is inappropriate to diagnosis equipment through this study.

• Korean Journal of Poultry Science
• /
• v.32 no.4
• /
• pp.291-300
• /
• 2005

Two experiments were carried out to assess the appropriate incubation conditions namely; duration, moisture content and the ideal microbial inoculant for fermented dried food waste(EW) offered to broilers. The nutrient utilization of birds fed the FW diets at varying dietary inclusion rates was also compared with a control diet. In Experiment 1, different moisture contents(MC) of 30, 40, 50 and $60\%$ respectively were predetermined to establish the ideal duration of incubation and the microbial inoculant. A 1mL Aspergillus oryzae(AO) $(1.33\times10^5\;CFU/mL)$ was used as the seed inoculant in FW. This results indicated that the ideal MC for incubation was $40\~50\%$ while the normal incubation time was > 72 hours. Consequently, AO seeds at 0.25, 0.50, 0.75 and 1.00mL were inoculated in FW to determine its effect on AO count. The comparative AO count of FW incubated for 12 and 96 hours, respectively showed no significant differences among varying inoculant dosage rates. The FW inoculated with lower AO seeds at 0.10, 0.05 and 0.01mL were likewise incubated for 72 and 96 hours, respectively and no changes in AO count was detected(p<0.05). The above findings indicated that the incubation requirements for FW should be $%40\~50\%$ for 72 hours with an AO seed incoulant dosage rate of 0.10mL. Consequently, in Experiment II, after determining the appropriate processing condition for the FW, 20 five-week old male Hubbard strain were used in a digestibility experiment. The birds were divided into 4 groups with 5 pens(1 bird per pen). The dietary treatments were; Treatment 1 : Control(Basal diet), Treatment 2 : $60\%$ Basal+4$40\%$ FW, Treatment 3 : $60\%$ $Basal+20\%\;FW+20\%$ AFW(Aspergillus oryzae inoculate dried food-waste diet) and Treatment 4: $60\%$ Basal+$40\%$ Am. Digestibility of treatment 2 was lowed on common nutrients and amino acids compared with control(p<0.05) and on crude fat and phosphorus compared with AFW treatments(T3, T4)(plt;0.05). Digestibility of treatment 3 and 4 increased on crude fiber and crude ash compared treatment 2 (p<0.05). Digestibility of control was high on agrinine, leucine, and phenylalnine of essential amino acids compared with treatment 3 and 4(p<0.05), and diestibility of treatment 3 and 4 was improved on arginine, lysine, and threonine of essential amino acids. Finally, despite comparable nutrient utilization among treatments, birds fed the dietary treatment containing AO tended to superior nutrient digestion to those fed the $60\%$ Basa1+$40\%$ FW.

• Korean Journal of Psychosomatic Medicine
• /
• v.4 no.2
• /
• pp.269-276
• /
• 1996

A theroretical study was made on the psychodynamism of somatoform disorder. Somatoform disorder is caused by a defense mechanism of somatization. Somatization is the tendency to react to stimuli(drives, defenses, and conflict between them) physically rather than psychically(Moore, 1990). Ford(1983) said it is a way of life, and Dunbar(1954) said it is the shift of psychic energy toward expression in somatic symptoms. As used by Max Shur(1955), somatization links symptom formation to the regression that may occur in response to acute and chronic conflict. In the neurotic individual psychic conflict often provokes regressive phenomena that may include somatic manifestations characteristic of an earlier developmental phase. Schur calls this resomatization. Pain is the most common example of a somatization reaction to conflict. The pain has an unconscious significance derived from childhood experiences. It is used to win love, to punish misdeeds, as well as a means to amend. Among all pains, chest pain has a special meaning. Generally speaking, 'I have pain in my chest' is about the same as 'I have pain in my mind'. The chest represent the mind, and the mind reminds us about the heart. So we have a high tendency to recognize mental pain as cardiac pain. Kellner(1990) said rage and hostility, especially repressed hostility, are important factors in somatization. In 'Psychoanalytic Observation on Cardiac Pain', psychoanalyst Bacon(1953) presented clinical cases of patients who complained of cardiac pain in a psychoanalytic session that spread from the left side of their chests down their left arms. The pain was from rage and fear which came after their desire to be loved was frustrated by the analyet. She said desires related to cardiac pain were dependency needs and aggressions. Empatic relationship and therapeutic alliances are indispensable to psychotherapy in somatoform disorder. The beginning of therapy is to discover a precipitating event from the time their symptoms have started and to help the patient understand a relation between the symptom and precipitating event. Its remedial process is to find and interpret a intrapsychic conflict shown through the symptoms of the patient. Three cases of somatoform disorder patients treated based on this therapeutic method were introduced. The firt patient, Mr. H, had been suffering from hysterical aphasia with repressed rage as ie psychodynamic cause. An interpretation related to the precipitating event was given by written communication, and he recovered from his aphasia after 3 days of the session. The second patient was a dentist in a cardiac neurosis with agitation and hypochondriasis, whose psychodynamism was caused by a fear that he might lose his father's love. His symptom was also interpreted in relation to the precipitating event. It showed the patient a child-within afraid of losing his father's love. His condition improved after getting a didactic interpretation which told him, to be master of himself, The third patient was a lady transferred from the deparment of internal medicine. She had a frequent and violent fit of chest pains, whose psychodynamic cause was separation anxiety and a rage due to the frustration of dependency needs. Her symptom vanished dramatically when she wore a holler EKG monitor and did not occur during monitoring. By this experience she found her symptom was a psychogenic one, and a therapeutic alliance was formed. later in reguar psychotherapy sessions, she was told the relaton between symptoms and precipitating events. Through this she understood that her separation anxiety was connected to the symptom and she became less terrifide when it occurred. Now she can travel abroad and take well part in social activities.

• Journal of Korean Society of Forest Science
• /
• v.2 no.1
• /
• pp.19-28
• /
• 1962

Total area of bamboo groves in Korea which is limited to $37^{\circ}$ north latitude, i.e., to southern part of Chungchung-nam-do Province and Kangwon-do Province, is 3,235ha., but this country must import about 3,000 metric ton's bamboo culms from Japan every year. It may be true that the country is not so fit for economical cultivation of bamboo groves from the view point of climatic condition, but the author believes that self-sufficiency in bamboo is not impossible if some scientific method for improving bamboo groves is introduced to our primitive groves. Keeping this point in his mind the auther tried to study on the bamboo groves in the country, and as the first step set about to investigate the actual state of twenty good bamboo groves located in Cholla-nam-do Province from March, 1961 to January, 1962. This is a report on some characters of bamboo culms and growing stock with samples collected in the present investigation. 1) Numbers of bamboo culm per 0.1ha. are 1,183 in average, 1,840 in maximum and 87.5 in minimum before harvesting. 2) According to owners' saying, 1960 was such an off-year that they could hardly see any yearling bamboos in groves, but in 1961 very many new bamboos are produced as follows: the proportion of the number of yearling bamboos produced this year to that of mature bamboos (over 2 years old) is 58.7% in average; the highest 110.5% and the lowest 16.8%. 3) the average diameter of culms at eye height is 6.5cm, but the biggest diameter comes to 11.2 cm, and the average diameters of yearling and mature bamboos are 6.5cm and 6.6cm respectively. 4) Internode length records 29.4 cm in average, the shortest 21.3 cm and the longest 38.4 cm. Average internode lengths of new culms and mature culms are 27.6 cm and 29.4 cm respectively. This shows that the internode length of new culms is in the decrease to that of maturer's. 5) Through this investigation, it was found that internode length is in the influence of the exposure and density of bamboo groves, i. e., the more the dencity of bamboo groves is and the more the exposure nears the north-east, the longer the internode length becomes (see Table 7 and 8). 6) In the growing stock of bamboo groves, bundles per 0.1ha. amount to 271 sok (unit of bundle) in total average, 445 sok in maximum and 126 sok in minimum. 7) Among twenty typical bamboo groves, chosen in each County in Cholla-nam-do Province, only one passes perfectly by Veda's standard rule* prescribing the good bamboo grove, but the eight groves shown in Table 9 could be recommended as good ones in Cholla-nam-do Province, because the auther believes that those groves may be improved better, if we pay more attention to the management of them. 8) Considering that they have managed their groves carelessly and primitively, and that unfortunately their groves must have faced almost on clear felling over the entire area at the time of the Korean War, we can surely expect much more increments in bamboo groves, if we introduce some scientific methods in managing their groves.

• Korean Journal of Animal Reproduction
• /
• v.22 no.4
• /
• pp.425-435
• /
• 1998

To improve the efficiency of nuclear transplantation in bovine, in this study the development in vitro of nuclear transferred (NT) embryos was compared by different activation regimens of the enucleated oocytes. The effect of developmental stage and culture system of donor nuclei on fusion and development in vitro of NT embryos were also evaluated. Oocytes were collected from Hanwoo ovaries obtained from slaughterhouse and matured in Ham's F-10 supplemented with hormones. After 20~22 h maturation, the oocytes were vortexed to be free from cumulus cells and subsequently their nucleus and the first polar body were removed. Enucleated oocytes were divided into 3 groups for activation; the oocytes of group I were activated with ionomycin for 5 min and subsequently incubated in 6-dimetylarninopurine (DMAP) for 4 h, Those of group II were treated with DMAP for 4 h at 39 h after onset of in vitro maturation (IVM) and those of group III were kept in room temperature ($25^{\circ}C$) for 3 h at 39 h after onset of IVM. After in vitro fertilization (IVF) the embryos for muclear donor were cultured either by group culture (20 embryos /50 ${mu}ell$ drop) or individually (1 embryo /50 ${mu}ell$ drop) for 4 day and 5 day. At day 4 and 5 after IVF, blastomeres were separated in calcium-magnesium free medium, and then classified into small (day 5: $\leq$ 38 ${\mu}{\textrm}{m}$, day 4: $\leq$ 46 ${\mu}{\textrm}{m}$) and large (day 5 : $\geq$ 38 ${\mu}{\textrm}{m}$, day 4 ; $\geq$ 46 ${\mu}{\textrm}{m}$). The separated blastomeres were replaced into enucleated and activated recipient cytoplasm. The blastomere-oocyte complexes were fused by electrically. The NT embryos were cultured in TCM-199 containing 10% FCS in 39$^{\circ}C$, 5% $CO_2$ incubator for 7 day. The results obtained were summarized as follows; There were no differences in fusion and development to blastocyst between groups as group I (68%, 10%), group II (75%, 14%) and group III (73%, 9%), respectively. However, the cell number in blastocyst of NT embryos in group III were significantly fewer than in the other groups (P＜0.05). No differences in fusion and development to blastocyst were found between individual or group cultured and between small or large blastomeres of day 4 and day 5 donor embryos. From these results, it was concluded that the combination of ionomycin and DMAP, or treatment of DMAP at 39 h after onset of IVM were useful for the efficient of production of NT bovine embryos, and the individual cultured embryos could be simply used as donor nuclei for NT bovine embryo.