• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.629-632
• /
• 2006

This study investigated the engineering properties of crushed sand, based on improvement quality technology, and washed sand concrete by conducting mock-up test, in order to verify the availability of crushed sand for full sized structure. Test results showed that fluidity, air content, supersonic waves and corrosion state of concrete using crushed sand had favorable results. In addition, it is found that compressive strength, drying shrinkage length change, hydration heat and neutralization of crushed sand concrete exhibited similar tendency, with that of washed sand concrete. The crushed concrete using developed quality improvement technology shows comparable performance to washed sand concrete.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표대회 논문집(III)
• /
• pp.940-945
• /
• 1998

Recently, serious cracking problems have been reported in this country while the process of actual massive concrete construction. he hydration heat arising from the chemical reaction of cement with water causes temperature differentials in between inside and outside of a structural member, and these temperature differentials induce thermal stresses. In this paper, we described on the practical application and quality control of the mass concrete mixed with fly-ash. This project is investigating adiabatic temperature rise test of concrete, mock-up test in the laboratory, ad B/P before placing the mass concrete in site. As a result, we can be prevent temperature cracking from the cement hydration heat of mass concrete and also can be showed up secure quality control flow chart of mass concrete.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.113-116
• /
• 2006

After laws for recycling promotion of construction wastes was established on December, 2003, successive technical and institutional measures related to construction wastes are driven. Typically quality standards for recycled aggregate were enacted and officially announced, and recently the quality assurance system for recycled aggregate is promoted to be established. In relation, this study reviewed major factors affecting certification examination necessary to carry out quality assurance system for recycled aggregate and related standards to guarantee the quality of recycled aggregate. More specifically it is suggested that working place examination related to manufacturing facility and planning, quality control manpower and system, environmental and safety control, etc, and quality inspection with classified by for road construction, for concrete, and for asphalt concrete are used as quality assurance standards.

• 한국건축시공학회지
• /
• 제7권4호
• /
• pp.125-132
• /
• 2007

The use of Self-Leveling material is increasing recently. This paper assesses the quality of surface layer of concrete floor when Self-Leveling material is defective. The paper shows how to predict the defect of SL material before construction begins. The relationship between the quality of surface layer of concrete floor and the defect of SL material was determined and the quality of surface layer of concrete floor was then estimated. The relations between the quality of surface layer and the defect of SL material were determine considering surface strength, moisture, and consistency of surface layer. Absorbing amount was used as the indicator of consistency and the absorbing amount of test material was measured. Then the relations between the test material and surface strength were determined. Generally concrete floor with greater consistency has greater surface strength, however in this study, we hound that high impact concrete floor could have lower surface strength as the consistency gets bigger. The relations between the level of defect occurred in SL material and the quality of surface layer were examined and we clarified that the surface layer with lower consistency gets higher possibility to occur exfoliation in early stage, one or two weeks after constructing SL material. When the consistency is sufficient, the occurring situation of defect depends upon the moisture of surface layer. Little amount of moisture gets higher possibility not to occur the defect. As the amount increases, fissure generates and early exfoliation may occur. In addition, the level of fissure is highly related with the surface strength.

• 한국건설관리학회논문집
• /
• 제1권2호
• /
• pp.53-62
• /
• 2000

콘크리트는 콘크리트 구조 건물의 주요 구조 재료로서, 그 재료적 설계 물성은 생산ㆍ준비$\cdot$타설$\cdot$보양$\cdot$마감 및 보수/보강 등 여러 단계에 걸친 복합적 프로세스에 의해서 결정된다. 또한 콘크리트는 주요 설계 물성이 상당한 시일이 경과한 후 달성되는 재료적 특성으로 인해서 결함을 발견하기에 상당한 어려움이 있으며 결함을 수정하기 위해서 많은 비용과시간이 필요하다. 따라서 콘크리트의 재료적 설계 물성을 확보하기 위해서는 위에서 설명한 각 단계별로 소요 성능을 측정하고 선행 단계에서의 결함이 후속 단계로 전파되지 않도록 함으로써 최종 단계 프로세스가 완료되면 전체 설계 물성을 확보할 수 있도록 하기 위한 효율적인 관리 절차가 필수적이다. 따라서, 본 연구에서는 첫째 기존 품질관리 절차서를 분석하고, 둘째 분석 결과에 따라 새로운 다중 코드를 이용한 맞춤식 체크 리스트를 제시하며, 셋째 맞춤식 체크리스트를 활용함으로써 콘크리트 부재 유지관리시 유용하게 사용될 콘크리트 이력데이터 구축방법을 제시하고, 마지막으로 맞춤식 체크리스트를 현업에 적용하고 적용성을 보완한 개선된 체크리스트를 제시하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.609-612
• /
• 2008

본 연구는 콘크리트의 강도특성에서 잔골재 품질의 영향을 평가하고자 한다. 순환골재 콘크리트의 강도특성에 관한 몇몇 연구가 진행되었으나 대부분의 실험이 실험실 내에서의 소규모 실험이기 때문에 현장적용시 오차가 발생할 수 있다. 따라서 본 연구에 사용된 콘크리트는 레미콘 배합에 의해 생산되었으며, 잔골재의 품질[고품질(순환잔골재) : 흡수율 5%이하, 절건밀도 2.2g/cm$^3$이상, 저품질(저품질순환잔골재) : 흡수율 8.0${\sim}$10.0%, 절건밀도 2.2g/cm$^3$이하]과 치환율[0, 30, 60, 100%(고품질), 35, 70%(저품질)]을 변수로 설정하였다. 실험결과 순환잔골재를 사용한 콘크리트의 공기량 경시변화는 천연골재에 비해 큰 차이를 보이지 않았다. 또한 순환 및 저품질 순환잔골재 콘크리트에서 잔골재 치환율과압축강도 및 파괴계수와의 상관성은 높지 않은 것으로 나타났다.

• 대한토목학회논문집
• /
• 제3권4호
• /
• pp.33-45
• /
• 1983

레디믹스트콘크리트가 배치 플랜트에서 출하되어 현장에서 타설을 완료 할 때까지의 운반시간이 지연되는 경우가 있으며, 이로 인하여 워커빌리티가 저하되어 적절한 조치를 취하지 않고서는 시공이 어려운 문제점이 종종 야기되고 있다. 그래서 레디믹스트콘크리트의 운반시간에 따른 품질변화를 알아보며, 저하된 워커빌리티의 개선과 아울러 소요의 품질을 유지하기 위한 수단으로 시멘트와 물 및 유동화제를 추가로 첨가하는 방법과 유동화제의 적정 첨가량을 구하기 위한 실험을 실시하였다. 그 결과 레디믹스트콘크리트에 유동화제를 첨가하여 재믹싱함으로써 품질개선에 얼마간 유효한 결과를 얻었다.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2003년도 학술발표논문집
• /
• pp.407-410
• /
• 2003

The actual quality of the concrete in the structure for Irrigation may differ from that represented by the cylinders because the age, consolidation, or curing of the in-place material may not be well represented by the standard test specimens. The objective of this paper is to offer a base data of specification is the best fit the ready-mixed concrete strength to the specified, and to address this deficiency, so that the strength information of the concrete in the structure for Irrigation can be rationally accounted for in the assessment of the quality condition of this. The strength of concrete in the hydraulic structures is checked using strength of core obtained from that, and 28-day-old cylinder strength is analyzed using cylinder data of the ready-mixed concrete.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 가을 학술발표회 논문집
• /
• pp.423-428
• /
• 1994

High strength concrete was placed at the mass concrete slabs, walls, pillars of RC building from August till August. And the construction is going on now. This paper presents mix design, production, quality control and experience with field application of high strength ready-mixed concrete under hot weathered conditions. It is shown to be possible to produce high strength concrete that has 45MPa compressive strength using superplasticizer and cement replaced with 20% fly-ash with appropriate control.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1995년도 가을 학술발표회 논문집
• /
• pp.164-168
• /
• 1995

As nation's infrastructure is getting old, nondestructive evaluation of existing structures and construction quality control are getting important. In this paper non-destructive evaluations of concrete members using impact echo and SASW methods are introduced. Both techniques are based on the stress wave propagations. Experimental tests were performed using beam type concrete member where voids and cracks are included. Within reasonable accuracy, void locations were detected using impact echo method and the dynamic modulus of concrete were measured using SASW method. Both NDT methods showed a feasibility for the implementation into quality evaluaton of concrete members in practice