• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.629-634
• /
• 2001

This study is to characterize the material property of early age high performance concrete emphasizing compressive strength using nondestructive testing methods. Three high performance concrete slabs of 600, 850 and 1100kg/$cm^{2}$ compressive strengths were prepared together with cylinders from same batches. Cylinder tests were peformed at the ages of 7, 14, 21 and 28 days after pouring. Using the impact echo method, the compression wave velocities were obtained based on different high performance concrete ages and compressive strengths. The equation to obtain the compressive strengths of high performance concrete has been developed using the obtained compression wave velocities. Using the SASW (spectral analysis of surface wave) method, the equation have also been developed to obtain the compressive strengths of high performance concrete based on the surface wave velocities.

• Computers and Concrete
• /
• v.11 no.6
• /
• pp.531-539
• /
• 2013

An experimental investigation of mechanical properties of jute fiber-reinforced concrete (JFRC) has been reported for making a suitable construction material in terms of fiber reinforcement. Two jute fiber reinforced concretes, called jute fiber reinforced normal strength concrete (JFRNSC) and jute fiber-reinforced high-fluidity concrete (JFRHFC), were tested in compression, flexure and splitting tension. Compressive, flexural and splitting tensile strengths of specimens were investigated to four levels of jute fiber contents by volume fraction. From the test results, Jute fiber can be successfully used for normal strength concrete (NSC) and high-fluidity concrete (HFC). Particularly, HFC with jute fibers shows relatively higher improvement of strength property than that of normal strength concrete.

• Computers and Concrete
• /
• v.9 no.4
• /
• pp.293-310
• /
• 2012

This paper discusses a new constitutive model called the high-rate brittle microplane (HRBM) model and also presents the details of a new software package called the Virtual Materials Laboratory (VML). The VML software package was developed to address the challenges of fitting complex material models such as the HRBM model to material property test data and to study the behavior of those models under a wide variety of stress- and strain-paths. VML employs Continuous Evolutionary Algorithms (CEA) in conjunction with gradient search methods to create automatic fitting algorithms to determine constitutive model parameters. The VML code is used to fit the new HRBM model to a well-characterized conventional strength concrete called WES5000. Finally, the ability of the new HRBM model to provide high-fidelity simulations of material property experiments is demonstrated by comparing HRBM simulations to laboratory material property data.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.05a
• /
• pp.147-148
• /
• 2016

Generally, the vegetable oil contains glycerin esther and free fatty acid. When the vegetable oil reacts with concrete, the glycerin esther from oil induces saponification by reacting with and hydrolyzing calcium hydroxide from cement hydration. As a result of this saponification, it has been reported the expansion of concrete. although the free fatty acid from vegetable oil, as an acid, can decompose the concrete by producing soluble salt from calcium hydroxide or CSH, the hydration products of cement, there was no report on the harmful oil type for concrete. therefore, in this research, the property change of cement mortar incorporating fly ash was analyzed experimentally by immerging various types of vegetable oils.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1990.10a
• /
• pp.107-112
• /
• 1990

Chromatograms of asphalt cements were observed using high pressure - gel permeation chromatography (HP-GPC). The chromatogram characterzed profile of molecular size distribution of asphalt cements. Bituminous concretes using the asphalt cements were prepared in laboratory to measure mechanical properties, tensile strength (TS) and resilient modulus (MR), in dry and wet conditions. Three sources of AC-20 Asphalt cements and one aggregates were used for GPC test and strength test. Results of mechanical property tests and GPC tests were analyzed to evaluate correlation between those two results. Regression analysis showed strong correlation between a mechanical property and sliced percent areas of GPC profile. Mathematical models were developed for estimating mechanical properties of asphalt cement concrete based on HP-GPC data.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.2
• /
• pp.67-73
• /
• 2016

When assessing crack initiation of fiber reinforced concrete, usually tensile strength or flexural strength is becomes indicator, but also depend on the curing effect take place during the production of specimen. In general, after conducting concrete specimen is cured by water at temperature $20{\pm}3^{\circ}C$ in laboratory, and accomplished the assessment of strength, but most of concrete structure is kept in drying condition after moist curing through the prescribed period. However, unlike these trends that technological advances have been made, influence of the difference of curing method on crack strength is not yet clear. Therefore, in this study, it is examined on the effect of curing methods affecting the mechanical property of fiber reinforced concrete, especially crack strength.

• Computers and Concrete
• /
• v.7 no.2
• /
• pp.191-202
• /
• 2010

A laboratory investigation was conducted to characterize the constitutive property behavior of Cor-Tuf, an ultra-high-performance composite concrete. Mechanical property tests (hydrostatic compression, unconfined compression (UC), triaxial compression (TXC), unconfined direct pull (DP), uniaxial strain, and uniaxial-strain-load/constant-volumetric-strain tests) were performed on specimens prepared from concrete mixtures with and without steel fibers. From the UC and TXC test results, compression failure surfaces were developed for both sets of specimens. Both failure surfaces exhibited a continuous increase in maximum principal stress difference with increasing confining stress. The DP tests results determined the unconfined tensile strengths of the two mixtures. The tensile strength of each mixture was less than the generally assumed tensile strength for conventional strength concrete, which is 10 percent of the unconfined compressive strength. Both concretes behaved similarly, but Cor-Tuf with steel fibers exhibited slightly greater strength with increased confining pressure, and Cor-Tuf without steel fibers displayed slightly greater compressibility.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.509-512
• /
• 2006

We have many environmental problems by the polluted materials as a results of mechanical development these days. So people want to use building products made from natural things and take a good effect for people from those bio products. We can instance electron wave shelding, far infrared ray and anion emission, and anti-bacterial property as the latest trend of the bio building material. So we had a experiment to investigate how much bio materials affect concrete when we use in the concrete with cement substitution. We tested slump, 7days compressive strength, and air contents for physical properties of bio concrete. The result is that bio concretes with four bio ingredients have proper values comparing with target values for slump and air content but lower compressive strength than plain concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.225-228
• /
• 2006

To clarify the one body behavior of reinforcing bar and concrete, it is important to investigate bond characteristics between two materials. Bond strength is decided by applied force and interface area between reinforcing bar and concrete. And, the resultant force of chemical adhesive force, frictional force, and mechanical interaction are to be main factors. Property of concrete influences on chemical adhesive force and frictional force; bond strength is decreased by corrosion of reinforcing bar, as the result, durability is also decreased. In this study, to confirm bond characteristics with property of concrete, w/c ratio and blending of mineral admixture were selected as the main test parameters. The results obtained from this study will be used as the basic data for bond characteristics with corrosion.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.129-136
• /
• 1998

In this study, lightweight aggregates were developed to see the possible application as a structural uses. For the evaluation purpose, several testings were conducted to compare the physical characteristics between the controlled lightweight aggregates and other lightweight aggregates purchased from different sources. The tests included property changes of fresh concrete and strength characteristics of hardened concrete for both normal and high strength ranges. In addition, a experiment was performed to analyze the freezing and thawing resistance of new lightweight aggregate concrete against other lightweight aggregate concrete against other lightweight aggregate concretes with some experimental parameters such as lightweight aggregates, curing conditions, and water-cement ratio. The test showed that the new lightweight aggregate could be used structural components. Continuous study will be planned for future evaluations.