• Advances in concrete construction
• /
• v.4 no.4
• /
• pp.243-261
• /
• 2016

This research study focuses on utilizing sandstone which is overburden waste rock in coal mines to use in concrete as a replacement of fine aggregate. Physical properties of sandstone like water absorption, moisture content, fineness modulus etc., were found to be similar to conventional fine aggregate. Scanning Electron Microscope (SEM) analysis was carried out for analysing elemental composition of sandstone. There was no sulphur content in sandstone which is a good sign to carry the replacement. Fine aggregate was replaced with sandstone at 25%, 50%, 75% and 100% by volume and moulds of concrete cubes and cylinders were prepared. Compressive strength of concrete cubes was tested after 3, 7 and 28 days and split tensile & flexural strength was determined after 28 days. The strength was found to be increasing marginally with increase in sandstone content. Fine aggregate that was replaced by 100% sandstone gave highest strength among all the replacements for the compressive, split tensile and flexural strengths. Though increase in strength was marginal, still sandstone can be an effective replacement for sand in order to save the natural resource and utilize the waste sandstone.

• Structural Engineering and Mechanics
• /
• v.72 no.2
• /
• pp.155-168
• /
• 2019

This paper presents the results of an experimental investigation on the compressive strength of small scale concentrically axially loaded fiber-reinforced polymer (FRP) confined plain concrete columns, with cylinder concrete strength 19 MPa. For columns with circular (150-mm diameter) and square (150-mm side) cross sections wrapped with glass- and carbon-FRP sheets (GFRP and CFRP, respectively) applied with dry lay-up the effect of different jacket schemes and different overlap configurations on the confined characteristics is investigated. Test results indicate that the most cost effective jacket configuration among those tested is for one layer of CFRP, for both types of sections. In square sections the location of the lap length, either in the corner or along the side, does not seem to affect the confined performance. Furthermore, in circular sections, the presence of an extra wrap with FRP fibers parallel to the column's axis enhances the concrete strength proportionally to the axial rigidity of the FRP jacket. The recorded strains and the distributions of lateral confining pressures are discussed. Existing design equations are used to assess the lateral confining stresses and the confined concrete strength making use of the measured hoop strains.

• 한국도로학회:학술대회논문집
• /
• 2006.10a
• /
• pp.229-236
• /
• 2006

• Steel and Composite Structures
• /
• v.2 no.4
• /
• pp.259-276
• /
• 2002

In the present investigation the experimental and theoretical flexural and compressive behavior of short tubular steel columns filled with plain concrete and fiber-reinforced concrete (FRC) was examined. For a given length of the members, the effects of different geometry and dimensions of the transverse cross-section (square and circular) were investigated. Constituent materials were characterized through direct tensile tests on steel coupons and through compressive and split tension tests on concrete cylinders. Load-axial shortening and load-deflection curves were recorded for unfilled and composite members. Finally, simplified expressions for the calculus of the load-deflection curves based on the cross-section analysis were given and the ultimate load of short columns was predicted.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10a
• /
• pp.161-166
• /
• 2000

To save efforts for capping in the compressive strength tests of concrete, unbonded capping system has been standardized by ASTM C 1231 and AS 1012.9, respectively. These standards, however, do not sufficiently give a full detail of accessories such as steel retaining cap and rubber pad, especially hardness of rubber. Hence, without testing for sizes of steel retaining cap and rubber pad, tests for the quality control of rubber pads were conducted in detail according to Japanese studies. Based on tests, the range of hardness for rubber pad by the compressive strength(200~ 400kgf/$\textrm{cm}^2$) of concrete has been proposed and the guideline of reuses of a rubber pad is described.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.05a
• /
• pp.143-144
• /
• 2016

The core drilling method is considered to be the most effective and common method of assessing the compressive strength of concrete in existing reinforced concrete buildings for structural repair and retrofit. In general, core specimens within reinforcing bars are not permitted in the regulations with regard to assessing concrete strength even if the core specimens can contain the bars in some cases. The purpose of this study is to investigate the effects of the reinforcement arrangement on the concrete compressive strength as a basic research to propose the quantitative criteria of strength for core specimens containing reinforcements. To complete the basic research, cylinder specimens inserted in a variety of reinforcement arrangements were prepared and tested.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.10a
• /
• pp.101-107
• /
• 1996

In this study, the wedge splitting test (WST) specimens with various strength levels were tested to investigate the fatigue crack growth behavior of concrete. Selected test variables were concrete compressive strength with 2 levels (28 MPa, 60 MPa, 100 MPa) and maximum fatigue loading with 2 levels (75%, 85%). Fatigue testing was preceded by fracture energy test and the crack growth was measured by means of the compliance calibration method, 60 WST specimens were cast for the fatigue test, and 6 companion cylinders ($\phi$100${\times}$ 200 mm) for each batch. In fatigue test, the frequency of loading cycle was 1 Hz, and the minimum fatigue loading level was 5~10 % of ultimate monotonic loading. On the basis of the experimental results, a fracture mechanics-based empirical relationships for fatigue crack growth rate (da/dN-$\Delta$KI relationships) were presented. In addition, the effect of initial notch depth on the fracture energy and the validity of compliance calibration technique for the WST were shown.

• International Journal of Concrete Structures and Materials
• /
• v.11 no.2
• /
• pp.315-325
• /
• 2017

The purpose of the paper is to determine the influence of two widely used steel fibers and polypropylene fibers on the sulphate crystallization resistance, freeze-thaw resistance and surface wettability of ultra-high performance concrete (UHPC). Tests were carried out on cubes and cylinders of plain UHPC and fiber reinforced UHPC with varying contents ranging from 0.25 to 1% steel fibers and/or polypropylene fibers. Extensive data from the salt resistance test, frost resistance test, dynamic modulus of elasticity test before and after freezing-thawing, as well as the contact angle test were recorded and analyzed. Fiber hybridization relatively increased the resistance to salt crystallization and freeze-thaw resistance of UHPC in comparison with a single type of fiber in UHPC at the same fiber volume fraction. The experimental results indicate that hybrid fibers can significantly improve the adhesion properties and reduce the wettability of the UHPC surface.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.582-589
• /
• 2006

Shear wane velocity is important property for grasping the dynamic characteristics of material. It is has been used in various fields such as non-destructive testings of structures, seismic analysis of geotechnical structures and maintenance of concrete structure, and etc. Usually, shear wave velocities of rock cores and concrete cylinders are determined by free-free resonance tests, Shear wave measurement in free-free resonance tests is not straightforward, as compared with rod wave and flexural wane measurements. In This study, a new technique using resonance features of flexural and shear waves were proposed in which the nodal points for the fundamental mode of flexural waves were employed to generate and measure the shear waves with the flexural waves minimized. The real measurements for aluminum cylinders proved validity and reliability of the proposed algorithm. In addition to the proposed algorithm, the effects of material properties on elastic-wave velocities in resonance measurements were also studied. In summary, a new framework of the resonance measurements for shear-wave velocity determination was established, based on the results of this thesis.

• Magazine of the Korea Concrete Institute
• /
• v.11 no.2
• /
• pp.261-270
• /
• 1999

In these days, construction activities have caused civil petitions associated with vibration-induced damages or nuisances. Therefore, it is strongly needed to develop a remedial technique to mitigate unfavorable effects. The objective of this experimental research is to investigate material and structural dynamic characteristics of vibration-controlled concretes which have been proportionally mixed with various vibration reducing material, such as latex, rubber powder, plastic resin, polystyrofoams and etc. Normal and high strength concrete specimens are also prepared for corresponding comparison. As part of the recycling research for obsolete rubber and plastic materials, 32 concrete cylinders and 10 concrete flexural beams have been made for material and structural dynamic properties, respectively. In accordance with the resonance test on concrete cylinders, it can be concluded that concrete with vibration-reducing material have relatively larger material damping ration than normal or high strength concrete. Styrofoam is determined to be very effective vibration-reducing mixtures. From the vibration test on 10 concrete flexural beams, meamwhile, of importance observations was that material damping ratio is very smaller than structural damping ratio of corresponding specimen. But further vibration test on more flexural beams should be strongly needed by varying support conditions.