• Korean Institute of Interior Design Journal
• /
• no.36
• /
• pp.143-150
• /
• 2003

CAD System that was introduced In 1980 has significantly changed its way with the informatization in late 1990s. Nevertheless, tremendous data including interior Design has been produced, but it has been mixed without any organized direction. This study reviews the influence of Computer in interior Design Industry related to other Industries and searches for the common directionality that exists inside that diversity On the basis of this review, this study aims to make knowledge that is the new value from the Computer media as the guideline for research and development. For analysis, this study considers the development situation of other industries and the Computer systematization process in Korea and abroad at the same time on the basis of the change of interior Design process by CAD System.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.4
• /
• pp.356-363
• /
• 2016

The design methodology of an adequate input voltage and magnetizing inductance to minimize reactive power is suggested to design a wireless power transfer (WPT) converter for high-power transfer efficiency. To increase the magnetizing inductance, the turn number of the WPT coil is increased, thus causing high parasitic resistance in the WPT coil. Moreover, the high coil resistance produces high conduction loss in the transfer and receive coils. Therefore, the analysis of conduction loss is used in the design of the WPT coil and the operating point of the WPT converter. To verify the proposed design methodology, the mathematical analysis of the conduction loss is presented by experimental results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.13 no.1
• /
• pp.77-96
• /
• 1989

In diesel engines, it is inevitable that the torsional vibration is produced by the fluctuation of engine torque. Therefore, if the occurence of torsional vibration is confirmed in the design stage or the torsional vibration is observed on the bed of test run, it is necessary to establish some preventive measures to avoid dangerous conditions. Major preventive measures are as follows : 1. Changing the natural frequency of shaft system. 2. Repressing the vibration amplitude by the damping energy. 3. Counterbalancing the exciting torque by the resistant torque. 4. Counterbalacing the harmonic component of exciting energy. In above methos, the damper is the last measure to be used for controlling the torsional vibration. In this thesis, the design of viscous damper that absorbs the exciting energy is investigated and a number of problems associated with the design of viscous damper are treated and a computer pregram for the process of damper design is developed. A viscous damper for a high speed diesel engine is designed and its effect is simulated by the author's computer program.

• IEIE Transactions on Smart Processing and Computing
• /
• v.3 no.4
• /
• pp.167-172
• /
• 2014

In this paper we propose a waveform design algorithm that localizes the maximum output power in the target direction. We extend existing monostatic radar optimal waveform design schemes to bistatic multiple-input multiple-output (MIMO) radar systems. The algorithm simultaneously calculates the direction of departure (DoD) and the direction of arrival (DoA) using a two-dimensional multiple signal classification (MUSIC) method, and successfully localizes the maximum transmitted power to the target locations by exploiting the calculated DoD. The simulation results confirm the performance of the proposed algorithm.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.03a
• /
• pp.147-154
• /
• 1995

In this paper, a computer-aided design system for axisymmetric deep drawing process will be described. An approach to the system is based on the knowledge based system. The system has been written in AutoLISP with personal computer. The system is composed of four main modules, such as input , geometrical design, test & rectification and user modification . The system which aids designer provides powerful capabilities for the design of axisymmetric deep drawing process.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.195-196
• /
• 2006

Direct laser sintering (DLS) technology for the resign coated sand is one of attractive technologies to produce molds and cores for the foundry industry rapidly and cost effectively. The objective of this case study is to develop casting pilot models using computer simulation technology, DLS RP machine and industrial computed tomography. The proposed casting design was verified by the Z-Cast software in the fields of fluid flow and solidification during the casting process. Casting parts with aluminum alloy using the post-curing treated sand moulds and cores are accurate to dimension and defect free.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.10 no.1
• /
• pp.1-14
• /
• 1973

In the Department of Naval Architecture, Seoul National University, the development of computer programs for the computer-aided ship design sponsored by the Ministry of Science and Technology has been begun. The project is to be accomplished as a four-year plan, and the results of the works of the first year, preliminary design of dry-cargo ships based on an optimization technique and some fundamental calculations accompanied with the basic design of ships such as calculations of displacement, hydrostatic characteristics of hull forms, stability, floodable length, load line and longitudinal section modulus, are given in the Report R-72-9[9] published by the sopnsor for the public interests. In this paper, the philosophy and methodological principles with which the preliminary design program given in Appendix II was developed are summerized.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.2
• /
• pp.331-338
• /
• 2013

A new reliability calculation method is proposed based on design sensitivity analysis by the finite element method for nonlinear performance constraints in the optimal design of electromagnetic devices. In the proposed method, the reliability of a given design is calculated by using the Monte Carlo simulation (MCS) method after approximating a constraint function to a linear one in the confidence interval with the help of its sensitivity information. The validity and numerical efficiency of the proposed sensitivity-assisted MCS method are investigated by comparing its numerical results with those obtained by using the conventional MCS method and the first-order reliability method for analytic functions and the TEAM Workshop Problem 22.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.6
• /
• pp.125-131
• /
• 2005

The purpose of this study is an optimization of gate valve made by forging method instead of welding method. In this study, we propose an optimal shape design to improve the mechanical efficiency of gate valve. In order to optimize more efficiently and reliably, the meta-modeling technique has been developed to solve such a complex problems combined with the DACE (Design and Analysis of Computer Experiments). The DACE modeling, known as the one of Kriging interpolation, is introduced to obtain the surrogate approximation model of the function. Also, we prove reliability of the DACE model's application to gate valve by computer simulations using FEM(Finite Element Method).

• Journal of Engineering Education Research
• /
• v.26 no.1
• /
• pp.12-19
• /
• 2023

With the introduction of the accreditation of engineering programs in Korea, universities affiliated with the programs have opened introductory engineering design courses for first- or second-year students. Since these courses mainly aim at cultivating problem-solving skills through team projects, this type of classes has opened as face-to-face classes. However, from the beginning of 2020, online teaching was recommended or forced on universities due to the COVID-19 pandemic. Thus, effective design of online courses on introductory engineering design was inevitable during the period. In this paper, we introduce a case study of the course in the Department of Computer Science at S University in Fall 2021. Through concrete suggestions on project areas, selection of team members considering grade levels and interest, several systems for prevention of free riding, and carefully designed open-book exams, the course resulted in both high achievements and high satisfaction.