• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2010.05a
• /
• pp.67-70
• /
• 2010

This study investigates the physical properties of the acrylic emulsion mortar according to variable composition set of redispersible emulsion powders. This materials have to be composed of many types of binders and chemical additives. So it is difficult to decide suitable mixing proportion of composition materials. The redispersible emulsion powders using "2, 4, 6, 8kg" of EVA polymers dispersion ranges are prepared with acrylic emulsion mortars and were tested for basic characteristics such as flexural, and compressive strength, wheel load. Through experiments we found that the improved formula to satisfy the standard of wheel load by EVA polymers, and the masration rangs between about 2.0% to 2.6% which the white portland cenmet and EVA polymers is good for resistauce wheel load.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.146-147
• /
• 2014

In this study, as the resistance of the carbonation for high volume admixture incorporating concrete, coating effect of using refined cooking oil in the surface of high volume admixture incorporating concrete has been tested. The following results could be made as the conclusion. For the fresh concrete, the slump and air content has been identified as satisfying the target range. For the hardened concrete, comparing with specimen of Plain, specimen with coating showed better long age compressive strength. For the carbonation speed, the specimen of FA30 showed highest speed and the specimen of BS60 showed higher speed than specimen of Plain. For all the specimens coated with RCO, as the decrease of capillary pores inside the concrete, the carbonation speed has been obviously decreased and with even better effect than using PEP coating. It could be identified that specimens with coating by RCO showed good effect on refrain the speed of carbonation.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.11a
• /
• pp.49-52
• /
• 2008

The present study was to develop a dry PFB method similar to the existing gypsum board construction method in order to apply the existing wet PFB method that uses fire-resistant adhesive. It was found that the existing wet method can produce concrete compressive strength of 80MPa and fire resistance of 3 hours with 30mm PF boards. The goal of development in this study was fire resistance of 3 hours through dry construction of 15mm fire-resistant boards. 1. Improved PF board was prepared by adding inorganic fiber to existing board and using aggregate with grain size of 3mm or less. Molding was done at temperature higher than that for existing PF board molding. While wet curing is used for existing PF boards, this study used dry curing in order to enhance heat insulation performance. 2. According to the results of fire resistance test, when the dry PF method was applied, the temperature of the main reinforcing bar was 116℃ in 15mm, 103.8℃ in 20mm, and 94℃ in 25mm, and these results satisfied the current standards for fire resistance control presented by the Ministry of Land, Transport and Maritime Affairs. When a 3-hour fire resistance test was performed and the external properties of the specimen were examined, the outermost gypsum board hardly remained and internal PF board maintained its form without thermal strain.

• KIEAE Journal
• /
• v.10 no.2
• /
• pp.3-8
• /
• 2010

Many countermeasures are presented to make excessive earth circumstance pollution better in the earth. A lot of researches are in progress to lessen $CO_2$ among the industries exhausting it. The industries manufacturing cement are making many countermeasures. Many concernments on ECO-friendly materials, rather than cement, are increased, and researches are in progress to develop them. Lime, material mostly used before Portland cement appeared, attracts the Occident as well as the Orient. In the Occident, lime mortar was used in common, for maintaining and repairing cultural properties, too. This study is aimed at offering basic materials for the modern use of lime, ECO-friendly material. This study measured the change of intensity and weight with lime, sand, and earth, basic materials of Samhoimool. As a result, at the beginning, hydrated lime displayed its density late, but as time was gone, density was promoted continuously. In addition, density was promoted, when it was given heat at the beginning. If heat-generation reaction of quicklime and water was used, density was promoted at the beginning, but liquidity showed a drop.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.477-480
• /
• 2003

This study discusses the fundamental properties of cement mortar with the kinds and adding ratio of stabilizing agent of recycled water. According to the results, fluidity and air content hardly make difference by the kinds and adding ratio of stabilizing agent. When recycled water is used, setting time is shortened slightly in comparison with plain mortar because of an increase of fine particle. And it is similar to the use of recycled water in the case of A, Band D(stabilizing agent), but shortened significantly in the case of C. Also, it does not show difference with variation of the adding ratio, but as the adding ratio increases, it approach to the value of plain mortar. When recycled water is used, compressive strength is similar to plain concrete, and it shows the larger value in order of D, C and A. As the adding ratio of stabilizing agent increases, it decreases at 3days, but increases at 7 and 28days. However, at the adding ratio of 0.5%, it decreases, instead. Length change ratio by drying shrinkage increases in the case of B in comparison with plain mortar, but is similar to plain mortar in the other stabilizing agent. As the adding ratio of stabilizing agent increases, it decreases, however, increases at the adding ratio of 0.5%

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.603-610
• /
• 2005

The end bearing behavior of piles socketed in weathered/soft rock is generally dependent upon the mass conditions of rock with fractures rather than the strength of intact rock. However, there are few available data and little guidance in the prediction of the end bearing capacity of drilled shafts socketed in weathered/soft rock, considering rock mass weathering. Therefore, a database of 13 load tests was constructed first, and new empirical relationships between the base reaction modulus of piles in rock and rock mass properties were developed. No correlation was found between the compressive strengths of intact rock and the base reaction modulus of weathered/soft rock. The ground investigation data regarding the rock mass conditions(e.g. Em, Eur, RMR, RQD) was found to be highly correlated with the base reaction modulus, showing the coefficients of correlation greather than 0.7 in most cases. Additionally, the applicability of existing methods for the end bearing capacity of piles in rock was verified by comparison with the field test data.

• Journal of the Korean Ceramic Society
• /
• v.33 no.3
• /
• pp.307-312
• /
• 1996

In following addition of 0.3, -0.6, 0.8, 1.0 and 5 weight percent MgSiF66H2O studies have been made of the setting and hardening characteristics of ordinary portland cement. MgSiF66H2O retarded the setting time of ordinary portland cement and extended the induction pariod of the hydration. In ordinary portland cement the setting characteristics were drastically altered especially at high MgSiF66H2O contents. Evidence was also obtained by the formation of a KSiF6 which was very fine particle. The results wee as follows. 1. Slump was slightly decreased when MgSiF66H2O added. 2. Setting time was retarded depending on the amount of retarding agent 2 to 8 hours 3. Compressive strength was almost same or some increased in comparision with opc. 4. When MgSiF66H2O was added to cement paste K2SiF6 were formed It was fine-sized distributed uniformly in cement grain and caused retardation of cement setting.

• Journal of the Korean Ceramic Society
• /
• v.48 no.1
• /
• pp.6-13
• /
• 2011

In this study, we used activated carbon (AC) and charcoal (CH) as carbon sources with $TiO_2$ powder to prepare spherical carbons containing titania (SCCT) by using phenolic resin (PR) as a bonding agent. The physicochemical characteristics of the SCCT samples were examined by BET, XRD, SEM, EDX, iodine adsorption and compressive strength. The photocatalytic activity was evaluated by measuring the removal efficiency of three kinds of organic dyes: methylene blue (MB), methyl orange (MO) and rhodamine B (Rh.B) under a UV/SCCT system. In addition, evaluation of chemical oxygen demand (COD) of piggery waste was done at regular intervals and gave a good idea about the mineralization of wastewater.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.13 no.2
• /
• pp.17-25
• /
• 2013

It is important to eliminate thermal bridge for achieving passive and environmental-friendly buildings. Structural members may frequently act as thermal bridges that become a conduit of energy. it is emphasized that thermal bridge breaker (TBB) system is necessary for blocking thermal bridge of the structural members. This TBB system has to maintain a performance to tensile and compressive stress which arises in member section in order to being realized structurally. Thus, it is composed with anchorage devices which obtain continuity with structural members inside building and rebar of cantilever balcony, and compression joint which resist compression stress occurring to TBB. Applying method of TBB's compression joint is designed to have high strength with comparatively small element section which can cover external load. This study carried out finite elements method based on compression experiment. Throughout the FEM analysis, this study provides information on finding optimal shape for compression joint of TBB which can suitably apply to current building balcony of Korea.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.63-68
• /
• 1998

The fluidity of high flowing concrete can be affected by numerous parameters which characterize either the cement of the admixture. The reactivity of a cement as determined by its chemical composition(especially its $C_3$A content), its fineness and its content in sulfates and alkalies obviously plays a key role in rheology of high flowing concrete in fresh state. Specific properties of high range water reducing AE agent used to enhance the workability of high flowing concrete also exert important influence. The purpose of this experimental study is to investigate and analyze the effect of cement and high range water reducing AE agent in fluidity, setting, compressive strength of high flowing concrete. As a result, we found that fluidity of high flowing concrete is affected greatly by kind of cement and high range water reducing AE agent, also, there is harmonic character between high belite cement and polycarbonic acid high range water reducing AE agent.