• Proceedings of the Korean Institute of Interior Design Conference
• /
• 2008.05a
• /
• pp.236-241
• /
• 2008

As the population of olds increases, the number of old people with capability increases, and they actively participate to social works with interests in healthy life and leisures. Therefore the demand rises to expand social facilities to support their spare time, while there are limitation, such as land, financial state, to build such facilities. In case of Japan, a solution of such problem occurs by compounding Social facilities for Old people and local facilities in practical and finacial aspect of the selection of site and managing the facilities and social aspect of supporting oppotunities to use various facilities. Such community based complex facilities supports services depending on the health state of Old people locally residing and increases the communication between different generation. The purpose of this research is aimed to analyze programs and space organization of advanced facilities in Japan and provide basical data for planning complex facilities for old people in Korea.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1936-1938
• /
• 2005

$Al(OH)_3$ is added to the silicone rubber for improvement of its resistance against surface discharge. In this paper, four kinds of $Al(OH)_3$ were added to the SIR during compounding. SIR was deteriorated by a corona treatment. Hydrophobicity recovery rate after corona treatment and arc resistance of SIR were investigated. Hydrophobicity recovery rate of SIR was evaluated by the measurement of contact angle. Arc resistance was evaluated by measuring weight loss of SIR after arc resistance test.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.195-196
• /
• 2007

In this paper, we investigated impurity content of carbon nanotube reinforced semiconductive shield materials and conventional semiconductive shield materials in power cables. To reduce impurity content, we used solution compounding method that an adding process of extra additives neglected. Impurity content measured through ICP-AES(Inductively Coupled Plasma Atomic Emission Spectroscopy). Also, impurity measured Ca, Cu, Fe, Al, Mg, Na, K, Si in eight. As a result, carbon nanotube reinforced semiconductive shield materials is lower than conventional semiconductive shield materials in impurity content by ICP-AES.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.591-593
• /
• 2003

Silicone composites for high voltage insulator(HVI SC) were prepared by adding aluminum trihydrate(ATH) treated by surface treatment agent to base silicone compound at the ratio of 100:20, 100:40, 100:60, 100:80, and 100:100, respectively. And also, ATH was treated by various surface treatment agents, such as stearic acid, acryl silane vinyl silane under compounding process. electrical properties were investigated for the various contents of ATH and solace-treatment agents we mlas ured volume resistivity, breakdown and tracking resistance were for HVISC containing ATH treated by viuyl silane.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.4
• /
• pp.285-290
• /
• 2005

Mechanical properties of rubber mat are influenced by many factors such as compounding ingredients and states of cure, process of rubber, and fillers. Our study aim is to investigate influence of N-isopropyl-N'-chloro-P-phenylene diamine antioxidant on the thermal aging and ozone cracking. In this work, the degradation of antiblastic rubber mat was studied and suggested mechanism to involve two-types of degradation, thermal-aging and ozone-cracking both of which can be contained antioxidant or non-antioxidant.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.1
• /
• pp.69-74
• /
• 2000

Applicability of Thermal field flow fractionation (ThFFF) was investigated for the analysis of masticated natural rubber (NR) adhesives produced bya hot melt mastication process. An optimum ThFFF condition for NR analysis was found by using tetrahydrofuran (THF) as a solvent/carrier and a field-programming. Low flowrate (0.3 mL/min) was used to avoid stopping the flow for the sample relaxation. Measured molecular weight distribution was used to monitor degradation of rubber during the mastication process. Rubber samples collected at three different stages of the mastication process and were analyzed by ThFFF. It was found that in an anaerobic process rubber degradation occurs at the resin-mixing (compounding) zone as well as in the initial break-down zone, while in an aerobic process most of degradation occurs at the initial breakdown zone. It was also found that E-beam radiation on NR causes a slight increase in the NR molecular weight due to the formation of a branched structure.

• Design & Manufacturing
• /
• v.13 no.3
• /
• pp.24-28
• /
• 2019

In this study, a study was carried out that could effectively produce a heat dissipation effect on plastic materials. Using carbon nanotube (CNT), aluminum powder and plastic, the material properties were tested in 2 cases of compounding ratio. The test sample mold was designed and constructed prior to the experiment. The experiments include tensile strength, elongation rate, flexural strength, flexural elasticity rate, eye-jaw impact strength, gravity and thermal conductivity. Results from 60% and 70% mixture of aluminium to plastic were tested, and a 10% less combined result was a relatively good property. For research purposes, the heat dissipation effect and light weighting obtained a good measure when the combined amount of Al was 60%.

• Design & Manufacturing
• /
• v.13 no.3
• /
• pp.6-10
• /
• 2019

In this study, a study was carried out that could effectively produce a heat dissipation effect on plastic materials. Using carbon nanotube (CNT), aluminum powder and plastic, the material properties were tested in 2 cases of compounding ratio. The test sample mold was designed and constructed prior to the experiment. The experiments include tensile strength, elongation rate, flexural strength, flexural elasticity rate, eye-jaw impact strength, gravity and thermal conductivity. Results from 60% and 70% mixture of aluminium to plastic were tested, and a 10% less combined result was a relatively good property. For research purposes, the heat dissipation effect and light weighting obtained a good measure when the combined amount of Al was 60%.

• Elastomers and Composites
• /
• v.6 no.2
• /
• pp.65-72
• /
• 1971

The purpose of this study is to establish an effective way to utilize the application of EPDM-Polymer blends. First of all, the physical properties for EPDM/NR blends and compounding agents were studied. The results are shown as follows: 1. In blending, tensile strength and tear strength decreased with increase in EPDM contents. It was not effective more than the ratio of EPDM/NR is 50/50. 2. Elongation is influenced by blending, especially the ratio of EPDM/NR is 50/50. 3. It was found that both the resistance for ozone and aging were much improved after blending.

• Elastomers and Composites
• /
• v.56 no.4
• /
• pp.217-222
• /
• 2021

In this study, random polypropylene (rPP) was compounded with two of monoglycerides, namely, glyceryl monolaurate (GML) and glyceryl monostearate (GMS), as antifogging agents to improve its antifogging performance. rPP film samples were prepared by a film-casting method using a three-roll casting machine after melt blending through a twin screw extruder. With an increase in the monoglyceride content, the melt flow index for rPP films with GML and GMS increased, and their yield strength decreased. The incorporation of GMS in rPP was proven to be more effective in improving its physical properties than was rPP with GML. When GML and GMS were separately added to the rPP film at contents of more than 1 phr and more than 5 phr, respectively, the film exhibited antifogging performance.