• 열처리공학회지
• /
• 제13권4호
• /
• pp.224-230
• /
• 2000

Garbon steel(SM35C) was gas nitrocarburized at $580^{\circ}C$ in $55%N_2-40%NH_3-5%CO_2$ mixed gas atmosphere, and then the steel was induction hardened at $850^{\circ}C$. The microstructure of gas nitrocarburized surface layer was observed by optical microscope and SEM. The phase analysis was carried out by X-ray diffraction method. The mechanical properties of gas nitrocarburized SM35C steel was evaluated by hardness, wear and fatigue test. The thickness of compound and diffusion layer were increased with increasing the gas nitrocarburizing time and the densest compound layer was obtained at 3 hours gas nitrocarburizing time. In case of 15sec induction hardening after gas nitrocarburizing, the surface hardness was decreased from 800Hv to 630Hv owing to the decomposition of compound layer, but wear resistance was increased because of increased hardness of diffusion layer. The fatigue strength of induction hardened steel after gas nitrocarburizing, $58kgf/mm^2$, was higher than $41.5kg/mm^2$ of gas nitrocarburized steel and $45kg/mm^2$ of induction hardened steel, respectively.

• Bulletin of the Korean Chemical Society
• /
• 제32권3호
• /
• pp.894-898
• /
• 2011

The first example of lead compound from $Pb(NO_3)_2$ and $H_3L$ N-heterocyclic ligand $(H_3L\;=\;(HO_2C)_2(C_3N_2)(C_3H_7)CH_2(C_6H_4)(C_6H_3)CO_2H)$, $[Pb_4(L')_4]{\cdot}5H_2O$ 1 (L' = OOC$(C_3H_7)(C_3N_2)CH_2(C_6H_4)(C_6H_3)COO)$, has been obtained under hydrothermal condition by decarboxylation, and characterized by elemental analysis, IR, TGDTA, and single-crystal X-ray diffraction. Compound 1 possesses a rare two-dimensional upper-lower offset terrace-like layer structure. In 1, crystallographic distinct Pb(II) ion adopts five-coordination geometry, and two lattice water molecules occupy the voids between 2-D layers. Results of solid state fluorescence measurement indicate that the emission band 458 nm may be assigned to $\pi^*-n$ and $\pi^*-\pi$ electronic transitions within the aromatic systems of the ligand L', however, the emission bands centred at 555 nm, 600 nm and 719 nm may be derived from phosphorescent emission ($\lambda_{excitation}$ = 390 nm).

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1995년도 제9회 학술발표회 논문개요집
• /
• pp.146-146
• /
• 1995

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2001년도 추계 학술발표강연 및 논문개요집
• /
• pp.107-107
• /
• 2001

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2000년도 추계학술발표강연 및 논문개요집
• /
• pp.86-86
• /
• 2000

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2004년도 춘계학술발표대회 및 제6회 신소재 심포지엄
• /
• pp.25-25
• /
• 2004

• 한국전자현미경학회:학술대회논문집
• /
• 한국현미경학회 1992년도 제23회 학술대회 연제 초록
• /
• pp.21-22
• /
• 1992

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.534-538
• /
• 2002

Dissimilar friction stir welding of aluminum (AI) alloy 1050 and magnesium (Mg) alloy AZ31 was successfully done in the limited welding parameters. The dissimilar weld showed good quality and facility compared to conventional fusion weld. Transverse cross section perpendicular to the welding direction had no defects. The weld was divided into base material of Al alloy, an irregular shaped stir zone and base material of Mg alloy. The irregular shaped stir zone was roughly located around the initial weld center. The weld interface near plate surface shifted from initial weld centerline to the advancing side. Hardness profile of the weld was heterogeneous, and the hardness value of the stir zone was raised to about 150 Hv to 250 Hv. The mixed phase was identified to intermetallic compound $Mg_{17}$Al$_{12}$ using x-ray diffraction method, energy dispersive x-ray spectroscopy (EDX) and electron probe micro analysis (EPMA). The formation of intermetallic compound $Mg_{17}$Al$_{12}$ during FSW causes the remarkable increase in hardness value in the stir zone.one.

• 한국식품과학회지
• /
• 제34권3호
• /
• pp.493-497
• /
• 2002

한국산 인삼 5년근을 60% acetone으로 추출하여 Sepadex LH-20 gel column chromatography, MCI-CHP 20 gel column chromatography, Bondapak $C_{18}$, column chromatography을 이용하여 TLC와 HPLC로 순도를 검증한 후 3 종의 polyphenol 화합물을 분리하였다. Compound I과 II는 Sepadex LH-20 gel column chromatography에서 증류수상에서 용출되었고 compound Ⅲ는 40% methanol 상에서 용출됨을 보아 compound II와 compound III는 흡착성이 강한 polyphenol 화합물이라 추정되었다. 혈압강하에 관여하는 효소인 angiotensin converting enzyme(ACE)의 저해효과는 compound II가 157 ppm에서 31.86%로 3 가지 분획물 중 가장 우수하였으며 compound I과 III는 높은 활성을 보이지 않았다. 통풍예방에 관여하는 xanthine oxidase 저해효과는 compound I, II에서 666 ppm에서 100%저해효과를 나타내었으나 compound III는 저해효과가 낮았다. Melanin을 형성하는 tyrosinase 저해효과를 실함한 결과 compound III는 400 ppm에서 28.6%의 저해효과를 나타내었고 Compound I과 II의 저해효과는 낮았다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.236-239
• /
• 2001

In this study, the compound materials of GRT/plastics (HDPE, LLDPE, LDPE, PP and PS) were developed. Their tensile strength, strain at yield and flexural modulus according to the change in CRT content were measured. And, the physical properties of the compound materials that the GRT content was changed in the waste vinyl HDPE and pure HDPE were measured, compared and analyzed. If tile GRT is added to PE plastics, the physical properties were superior to those of PP and PS, and in the case of HDPE, the waste vinyl HDPE had superior physical properties by the GRT content to the pure HDPE.