• The Journal of Advanced Prosthodontics
• /
• 제11권6호
• /
• pp.313-323
• /
• 2019

PURPOSE. Shear bond strength (SBS) test is the most commonly used method for evaluating resin bond strength of zirconia, but SBS results vary among different studies even when evaluating the same bonding strategy. The purpose of this study was to promote standardization of the SBS test in evaluating zirconia ceramic bonding and to investigate factors that may affect the SBS value of a zirconia/resin cement/composite resin bonding specimen. MATERIALS AND METHODS. The zirconia/resin cement/composite resin bonding specimens were used to simulate loading with a shear force by the three-dimensional finite element (3D FE) modeling, in which stress distribution under uniform/non-uniform load, and different resin cement thickness and different elastic modulus of resin composite were analyzed. In vitro SBS test was also performed to validate the results of 3D FE analysis. RESULTS. The loading flat width was an important affecting factor. 3D FE analysis also showed that differences in resin cement layer thickness and resin composite would lead to the variations of stress accumulation area. The SBS test result showed that the load for preparing a SBS specimen is negatively correlated with the resin cement thickness and positively correlated with SBS values. CONCLUSION. When preparing a SBS specimen for evaluating bond performance, the load flat width, the load applied during cementation, and the different composite resins used affect the SBS results and therefore should be standardized.

• Composites Research
• /
• 제36권6호
• /
• pp.388-394
• /
• 2023

복합재료 제조 시 수지의 함침성을 높이는 것은 제조 공정속도와 제품의 품질을 향상시키는 핵심 방법이다. 수지 개선은 중요하지만, 간단한 섬유 표면 처리로도 수지의 흐름성을 개선할 수 있다. 본 연구에서는 탄소섬유 직물에 다양한 플라즈마 처리 시간을 적용함으로써 수지와 섬유 간의 함침성을 향상하게 하였다. 플라즈마 처리에 따라 변화된 섬유 내 수지의 분산을 평가하기 위해 전기저항 측정법을 사용했다. 섬유 표면처리가 수지 함침성에 미치는 영향을 실시간으로 관찰할 수 있었다. 수지에 탄소섬유 토우를 삽입할 때 토우에 스며든 수지의 양을 측정하여 수지 함침성을 객관적으로 비교하였다. 5분 동안의 플라즈마 처리로 복합재료의 인장과 압축 강도가 50% 이상 향상되었으며, 보이드 함유율을 감소시키고 소화점 임계열류량을 증가시켰다. 마지막으로 건축용 복합재료 부품으로 사용되는 일부분을 활용하여 동적 굴곡피로시험을 실시했고, 3 kN하중 백만 회에도 복합재료 부품은 파손되지 않았다.

• Advanced Composite Materials
• /
• 제16권4호
• /
• pp.385-394
• /
• 2007

In this study, the effect of molding condition on the tensile properties for plain woven hemp fiber reinforced green composite was examined. The tensile properties of the composite were compared with those of the plain woven jute fiber composite fabricated by the same process. Emulsion type biodegradable resin or polypropylene sheet was used as matrix. The composites were processed by the compression molding where the molding temperature and its heating time were changed from 160 to $190^{\circ}C$ and from 15 to 25 min, respectively. The following results were obtained from the experiment. The tensile property of hemp fiber reinforced polypropylene is improved in comparison with polypropylene bulk. The strength of composite is about 2.6 times that of the resin bulk specimen. Hemp fiber is more effective than jute fiber as reinforcement for green composite from the viewpoint of strength. The molding temperature and time are suitable below $180^{\circ}C$ and 20 min for hemp fiber reinforced green composite. Hemp fiber green composite has a tendency to decrease its tensile strength when fiber content is over 50 wt%.

• Restorative Dentistry and Endodontics
• /
• 제35권1호
• /
• pp.30-39
• /
• 2010

본 연구에서는, 삼차원 유한요소분석법을 이용하여 복합레진 및 도재 라미네이트로 전치부 치간이개를 폐쇄할 때, 치간이개의 간격과 수복방법이 수복물의 접착계면에서의 응력분포에 미치는 영향을 비교하였다. 복합레진 혹은 도재 라미네이트로 수복된 모습의 유한요소모델을 형성하여 접착계면에서의 von Mises stress 분포 양태를 분석하였다. 수복형태는 크게 네 가지 범주를 고려하였다. Type I, 복합레진으로 인접면을 최소한으로 수복하는 경우; Type II, 치아 삭제 없이 복합레진으로 순면의 절반까지 수복하는 경우; Type III, 치아삭제 후복합레진으로 순면의 2/3까지 수복하는 경우; Type IV, 도재 라미네이트로 수복하는 경우 이 실험의 한계 내에서 다음과 같은 결론을 내릴 수 있었다. 모든 수복형태에 대해 치간이개 간격이 넓어질수록 접착계면에서 발생하는 최대응력 값은 증가하였으며, 도재 라미네이트로 치간이개 부위를 수복한 경우(Type IV)가 복합레진으로 수복한 경우(Type I, II, III)에 비해 높은 최대응력값을 나타내었다. 그러나 치간이개 간격이 넓어질수록 도재 라미네이트와 복합레진에서 발생하는 최대응력값의 차리는 감소하였으며, 치간이개 간격의 증가에 따른 최대응력값의 증가율은 도재 라미네이트가 복합레진으로 수복하는 경우보다 낮았다.

• Progress in Superconductivity
• /
• 제9권1호
• /
• pp.107-110
• /
• 2007

Bi/CNT composite and resin/CNT were chosen to improve the mechanical properties of $YBa_2Cu_3O_7$(YBCO) superconductor. In order to elucidate the effects of Bi/CNT composite and resin/CNT in YBCO superconductors, melt texture superconductor were impregnated by mixed compound of Bi and CNT into the artificial holes parallel to the c-axis, which were drilled on the YBCO superconductor. Various amount of Bi/CNT and resin/CNT were impregnated to YBCO superconductor with different holes diameters. Typical artificial holes diameters were 0.5, 0.7, and 1.0 mm respectively. Result of three-point bending test measurement, the bending strength with resin/CNT impregnation was improved up to 59.64 MPa as compared with 50.79 MPa of resin/CNT free bulk. Resin/CNT impregnation has been found to be one of the effective ways in improving the mechanical properties of bulk superconductor.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.284-287
• /
• 2002

During resin transfer molding(RTM) process, in case of thick parts, resin flow and void formation should be modeled three dimensionally even though for parts of small thickness, resin flow and void formation can be modeled two dimensionally. In this study, numerical simulations of three dimensional mold filling and void formation during RTM process.

• Restorative Dentistry and Endodontics
• /
• 제38권1호
• /
• pp.36-42
• /
• 2013

Objectives: This study evaluated the antibacterial effect and mechanical properties of composite resins ($L_{CR}$, $M_{CR}$, $H_{CR}$) incorporating chitosan with three different molecular weights (L, Low; M, Medium; H, High). Materials and Methods: Streptococcus (S). mutans 100 mL and each chitosan powder were inoculated in sterilized 10 mL Brain-Heart Infusion (BHI) solution, and was centrifuged for 12 hr. Absorbance of the supernatent was measured at $OD_{660}$ to estimate the antibacterial activities of chitosan. After S. mutans was inoculated in the disc shaped chitosan-containing composite resins, the disc was cleansed with BHI and diluted with serial dilution method. S. mutans was spread on Mitis-salivarius bacitracin agar. After then, colony forming unit (CFU) was measured to verify the inhibitory effect on S. mutans biofilm. To ascertain the effect on the mechanical properties of composite resin, 3-point bending and Vickers hardness tests were done after 1 and 3 wk water storage, respectively. Using 2-way analysis of variance (ANOVA) and Scheffe test, statistical analysis was done with 95% significance level. Results: All chitosan powder showed inhibition effect against S. mutans. CFU number in chitosan-containing composite resins was smaller than that of control resin without chitosan. The chitosan containing composite resins did not show any significant difference in flexural strength and Vickers hardness in comparison with the control resin. However, the composite resin, $M_{CR}$ showed a slightly decreased flexural strength and the maximum load than those of control and the other composite resins $H_{CR}$ and $L_{CR}$. Conclusions: $L_{CR}$ and $H_{CR}$ would be recommended as a feasible antibacterial restorative due to its antibacterial nature and mechanical properties.

• Restorative Dentistry and Endodontics
• /
• 제26권2호
• /
• pp.180-187
• /
• 2001

The structure of current guides is largely illogical and without any rational use of color ordering. The shade guides are generally made of plastic (rather than the actual composite material) and do not accurately depict the true shade. translucency. or opacity of the composite resin after polymerization. To solve this problem, information based on evaluations of natural teeth and material that use the same method and experimental conditions is necessary. The present investigation measured the color of natural maxillary anterior teeth in vivo and compared the results with those of composite resins. 269 Korean subjects were selected for this study. Intact central incisor. lateral incisor. and canine were selected. The clinical crowns were free of caries or restorations. The middle site of the coronal portion on the labial surface of the tooth was measured by Chroma Meter. The five light activated. resin-based materials (Amelogen, Denfil, Elitefil, Spectrum, Z100) were used in this study. Resin composite was condensed into plastic mold with a diameter of 8mm and a thickness of 4mm. pressed between glass plates to flatten the surfaces. and polymerized using a Visilux II visible light activation unit. The surfaces were polished sequentially on wet sandpaper. Color measurements of each specimen were accomplished by Chroma Meter. A computer program that compares each tooth color with each composite resin color was written and the minimum CIELAB color difference ($\Delta$E$^*$) between tooth and each material was calculated. Under the conditions of this study: 1. Teeth tend to become darker with advancing age. 2. Canines were darker. more yellow. and less green than incisors. 3. The teeth from the women were lighter. more green. and less yellow than the male teeth. 4. In general. composite resins were lighter. more green. and less yellow than teeth. Deficiencies were noted in Hues in YR range. 5. Mean color differences between the five composite resin products and teeth were detectable to the naked eye($\Delta$E$^*$>1.0). 6. In comparing the mean $\Delta$E$^*$ values of materials. Spectrum showed the least followed by Z100, Elitefil, Amelogen, Denfil in increasing order.

• 한국세라믹학회지
• /
• 제35권4호
• /
• pp.371-377
• /
• 1998

HAC/PVA계 MDF 시멘트 복합재료의 수분안정성을 향상시키기 위하여 수용성 epoxy resm을 시멘트 중량에 대해 5wt% 에서 15wt%까지 첨가하고 calendering법, extruding법, warm pressing법으로 성형하여 epoxy resin첨가량 및 제조공정이 수분안정성에 미치는 영향을 살펴보았다. 제조된 시편은 건조상태 및 3일, 7일, 14일간 물 속에 침적 후 습윤강도를 3점 곡강도로 측정하고 SEM으로 표면 가까운 부분의 파단면을 관찰하고 수은압입법으로 기공분포 및 기공율을 분석하여 침수 재령벌 MDF 시멘트 복합재료의 미세조직 변화를 살펴보았다. 적량의 epoxy resin 첨가에 의해 건조강도는 감소하였으나 전반적으로 수분안정성이 향상되었다. 그러나 전반적으로 epoxy의 함량이 많아지면 초기건조강도는 감소하는 경향을 나타나었으며 epoxy 첨가량이 7wt% 이상일 경우에서는 수분안정성 역시 별다른 효과를 볼 수 없었다. 제조공정별로는 warm pressing법에 의해 성형된 경우 epoxy 첨가에 의한 강도 및 수분안정성 향상 효율이 다른 방법보다 월등히 뛰어났으며 epoxy resinmdmf 5wt%, 7wt% 첨가하였을 때, 최적의 강도 및 수분안정성 효과를 얻을 수 있었다.

• The Journal of Advanced Prosthodontics
• /
• 제12권5호
• /
• pp.322-328
• /
• 2020

PURPOSE. This study evaluated the shear bond strength between 3D printed provisional resin and conventional provisional resin depending on type of conventional provisional resin and different surface treatments of 3D printed resin. MATERIALS AND METHODS. Ninety-six disc-shaped specimens (Ø14 mm × 20 mm thickness) were printed with resin for 3D printing (Nextdent C&B, Vertex-Dental B. V., Soesterberg, Netherlands). After post-processing, the specimens were randomly divided into 8 groups (n=12) according to two types of conventional repair resin (methylmethacrylate and bis-acryl composite) and four different surface treatments: no additional treatment, air abrasion, soaking in methylmethacrylate (MMA) monomer, and soaking in MMA monomer after air abrasion. After surface treatment, each repair resin was bonded in cylindrical shape using a silicone mold. Specimens were stored in 37℃ distilled water for 24 hours. The shear bond strength was measured using a universal testing machine at a crosshead speed of 0.5 mm/min. Failure modes were analyzed by scanning electron microscope. Statistical analysis was done using one-way ANOVA test and Kruskal-Wallis test (α=.05). RESULTS. The group repaired with bis-acryl composite without additional surface treatment showed the highest mean shear bond strength. It was significantly higher than all four groups repaired with methylmethacrylate (P<.05). Additional surface treatments, neither mechanical nor chemical, increased the shear bond strength within methylmethacrylate groups and bis-acryl composite groups (P>.05). Failure mode analysis showed that cohesive failure was most frequent in both methylmethacrylate and bis-acryl composite groups. CONCLUSION. Our results suggest that when repairing 3D printed provisional restoration with conventional provisional resin, repair with bis-acryl composite without additional surface treatment is recommended.