• Structural Engineering and Mechanics
• /
• 제82권5호
• /
• pp.595-609
• /
• 2022

Prestressed composite steel-concrete beams are still a technology restricted to repair sites of large-scale structures and spans. One of the reasons for that is the absence of standard frameworks and publications regarding their design and implementation. In addition, the primary normative codes do not address this subject directly, which might be related to a scarcity of papers indicating methods of design that would align the two technics, composite beams and external prestressing. In this context, this paper proposes methods to analyze the sizing of prestressed composite beams submitted to pre-tension and post-tension with a straight or polynomial layout cable. This inquiry inspected a hundred and twenty models of prestressed composite beams according to its prestressing technology and the eccentricity and value of the prestressing force. The evaluation also included the ratio between span and height of the steel profile, thickness and typology of the concrete slab, and layout of the prestressing cables. As for the results, it was observed that the eccentricity of the prestressing force doesn't significantly influence the bending resistance. In prestressed composite beams subjected to a sagging moment, the ratio L/d can reach 35 and 30 for steel-concrete composite slabs and solid concrete slabs, respectively. Considering the negative bending moment resistance, the value of the L/d ratio must be less than or equal to 25, regardless of the type of slab. When it comes to the value of the prestressing force, a variation greater than 10% causes a 2.6% increase in the positive bending moment resistance and a 4% decrease in the negative bending moment resistance. The pre-tensioned composite beams showed a superior response to flexural-compression and excessive compression limit states than the post-tensioned ones.

• Composites Research
• /
• 제37권4호
• /
• pp.356-362
• /
• 2024

본 연구는 농업 폐기물인 왕겨로부터 합성된 활성탄과 코코넛으로부터 합성된 상용 활성탄을 사용하여 제작된 축전식 탈염 전극의 나트륨 이온 제거 효율을 평가하였다. 아민화된 왕겨로부터 합성된 활성탄과 상용 활성탄의 비율이 각각 1:1인 Composite 1 전극과 2:1인 Composite 2 전극을 제작하여, 주사전자현미경과 표면적 분석을 통해 구조 변화를 관찰하였다. 나트륨 이온 제거 효율은 활성탄의 조성과 전압을 변수로 하여 시간에 따라 평가하였다. 그 결과, 왕겨로부터 합성된 활성탄을 포함한 더 많이 포함한 Composite 2 전극이 가장 높은 제거 효율을 보였다. Composite 2 전극은 1.2 V에서 최대 75%의 나트륨 이온 제거 효율을 달성하였으며, 이는 다양한 전압 조건에서 성능 평가를 통해 확인되었다. 또한, 전극의 실제 적용 가능성을 입증하기 위해 재사용 성능을 평가한 결과, 7회의 재사용 후에도 65% 이상의 흡착 성능을 유지하는 것으로 나타났다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.919-924
• /
• 2001

The purpose of this study is to prepare the basic data for the development of building board with expanded perlite. Each paste was mixed with four levels of water cement ratio(30, 40, 50, 60%), and expanded perlite was substituted with four levels of substitutive ratio(20, 40, 60, 80%) for the each paste. The physical property, compressive strength, bending strength and thermal conductivity of each cement composite which is made through previously described method were analyzed and the result was as follow. In the case of 80 percent substitutive ratio, the cement composite had a mechanical defect which was resulted from lack of paste content. In the case of 40 and 60percent substitutive ratio, the cement composite had sufficient strength, light weight and low thermal conductivity for application to fire resisting board.

• 대한토목학회논문집
• /
• 제28권2A호
• /
• pp.179-186
• /
• 2008

강성비를 이용한 합성형교 외측강성 영향 평가의 타당성을 평가하기 위하여 동일 강성비에서 거더 간격 변화에 따른 수정계수를 해석적으로 분석하였으며, 강성비, 하중 형태, 거더 간격이 수정계수에 미치는 영향을 평가하였다. 현장재하시험 및 기존 설계법의 수정계수와 본 연구에서 분석된 수정계수를 비교한 결과 강성비를 이용한 외측강성 영향 평가가 가능한 것으로 판단된다.

• 한국전자파학회논문지
• /
• 제18권3호
• /
• pp.341-350
• /
• 2007

본 논문에서는 주파수 조정의 상세 계획에 적용할 목적으로 M/W 중계망의 보호비 유도를 새로이 제안하였으며, 실제 시스템 및 주파수에 대해 동일 및 인접 채널 보호비의 계산 결과를 제시하였다. 가용율 예측에 근거한 제시된 방법은 합성 페이드 마진, 간섭-대-잡음의 비(I/N), 통합 필터 변별도, 시스템 변수로 나타낸 것이다. 계산 결과에 의하면 6.7 GHz, 60 km, 64-QAM, I/N=-6 dB, $BER=10^{-6}$에서 합성 페이드 마진 및 동일 채널 보호비는 각각 25.5 및 50.7 dB을 갖는다. 또한 40 MHz 인접 채널에 대해 통합 필터 변별도 및 인접 채널 보호비는 26.3 및 24.4 dB을 얻는다. 제안된 방법은 M/W 중계망의 보호비 도출에 있어 보다 상세하고 다양한 장치의 변수를 고려한 확장의 용이성 및 실용성 측면에서 이점을 갖는다.

• 소성∙가공
• /
• 제18권1호
• /
• pp.45-51
• /
• 2009

Shape memory alloy has been used to improve the tensile strength of composite by the occurrence of compressive residual stress in matrix using its shape memory effect. In order to fabricate shape memory alloy composite, TiNi alloy fiber and Al2024 sheets were used as reinforcing material and matrix, respectively. In this study, TiNi/Al2024 shape memory alloy composite was made by using hot press method. In order to investigate bonding condition between TiNi reinforcement and Al matrix, the micro-structure of interface was observed by using optical microscope and diffusion layer of interface was measured by using Electron Probe Micro Analyser. And the mechanical properties of composite with three parameters(volume fraction of fiber, cold rolling amount and test temperature) were obtained by tensile test. The most optimum bonding condition for fabrication the TiNi/Al2024 composite material was obtained as holding for 30min. under the pressure of 60MPa at 793K. The strength of composite material increased considerably with the volume fraction of fiber up to 7.0%. And the tensile strength of this composite increased with the reduction ratio and it also depends on the volume fraction of fiber.

• Steel and Composite Structures
• /
• 제52권3호
• /
• pp.249-271
• /
• 2024

In this scientific work, an analytical solution for the dynamic analysis of cross-ply and angle-ply laminated composite plates is proposed. Due to technical issues during the manufacturing of composite materials, porosities and micro-voids can be produced within the composite material samples, which can carry on to a reduction in the density and strength of the materials. In this research, the laminated composite plates are assumed to have new distributions of porosities over the plate cross-section. The structure is modeled using a simple integral shear deformation theory in which the transverse shear deformation effect is included. The governing equations of motion are obtained employing the principle of Hamilton's. The solution is determined via Navier's approach. The Maple program is used to obtain the numerical results. In the numerical examples, the effects of geometry, ratio, modulus ratio, fiber orientation angle, number of layers and porosity parameter on the natural frequencies of symmetric and anti-symmetric laminated composite plates is presented and discussed in detail. Also, the impacts of the kinds of porosity distribution models on the natural frequencies of symmetric and anti-symmetric laminated composite plates are investigated.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1680-1682
• /
• 1999

In this study, three kinds of Mn-Zn ferrite/Ni-Zn ferrite/$Ni_2Y$ ferroxplana prepared by the coprecipitation method were compounded with the silicon rubber, and the ring-shaped specimens with various compositional ratio were made. The material constant of ferrite/rubber composite absorbers was obtained by the 2-port method. The material constants of the ferrite/rubber composite microwave absorber made of three kinds of ferrite with various compositional ratio were utilized in design the matching conditions (frequency and thickness) on the impedance matching map. We were able to predict the matching condition from the matching map. On all three kinds of ferrite/rubber composite microwave absorber with less than compositional ratio 60[wt.%] of ferroxplana, we have found that the reflection losses were over than 20[dB] at the S-Band $(2\sim4[GHz])$ and C-Band$(4\sim8[GHz])$.

• 한국도로학회논문집
• /
• 제15권3호
• /
• pp.17-22
• /
• 2013

PURPOSES: Current theories for composite structures are too difficult for design engineers for construction. The purpose of this paper is to demonstrate to the practicing engineers, how to apply the advanced composite materials theory to the road structures. METHODS: Some laminate orientations have decreasing values of $D_{16}$, $B_{16}$, $D_{26}$ and $B_{26}$ stiffnesses as the ply number increases. The plate aspect ratio considered is from 1 to 5. In order to study the effect of $M_x$ on the equilibrium equations, two cases are considered. $M_x$ term is considered or neglected. RESULTS: Most of the road structures have high aspect ratios, for such cases further simplification is possible by neglecting the effect of the longitudinal moment terms. CONCLUSIONS: Most of the road structures have plate aspect ratios higher than 2. It is concluded that, for all boundary conditions, neglecting the longitudinal moment($M_x$) terms is acceptable if the aspect ratio (a/b) is equal to or higher than 2. This conclusion gives good guide line for design of the road structures.

• 대한기계학회논문집A
• /
• 제27권8호
• /
• pp.1338-1346
• /
• 2003

Three-dimensional formability of the thermoplastic laminar composite was studied according to manufacturing conditions. Five different types of the plain weave fabric were used as reinforcement with PET matrix. The square blank was made by press consolidation technique and formed in the type hemisphere. B-factor defined as the ratio of width of yarn and distance between yarns was used as the factor of formability in the type of plain weave fabric. The formability of PET/Glass fabric laminar composite was estimated in terms of forming rate and B-factor with the thickness distribution, area ratio of blank, and intra-ply shear angle. The thickness distribution across hemisphere was strongly affected by the B-factor, forming rate and blank thickness. The area ratio of blank was increased with B-factor, forming rate and blank thickness. Also, it was found that the intra-ply shear angle depends on the B-factor and forming rate.