• Journal of IKEEE
• /
• v.17 no.4
• /
• pp.393-397
• /
• 2013

This paper introduces the T/RX combined compact active channel module which is a key unit of the active phased array antenna(APAA) system. This module is mainly compoased of two parts for TX and RX fabricated on both sides of the active module for size reduction. The TX-part is primarily composed of a 3-stage amplifier, a microstrip phase shifter, a thermal compensation and a power detection circuit. The RX-part is composed of LNAs a microstrip phase shifter and BPFs for TX power rejection. Using the proposed design structure we can realized a compact active channel module having high performance.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.397-397
• /
• 2011

In a low aspect ratio (LAR) tokamak reactor with a superconducting toroidal field (TF) coil, the radial build of TF coil and the shield play a key role in determining the size of a reactor. For self-consistent determination of the reactor components and physics parameters, a system analysis code is coupled with one-dimensional radiation transport code. Conceptual design study of a compact superconducting LAR tokamak reactor with aspect ratio less than 2.5 was conducted and the optimum radial build was identified. It is shown that the use of an improved shielding material and high temperature superconducting magnets with high critical current density opens up the possibility of a fusion power plant with compact size and small re-circulating power simultaneously at low aspect ratio, and that by using an inboard neutron reflector instead of breeding blanket, tritium self-sufficiency is possible with outboard blanket only and thus compact sized reactor is viable.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.3
• /
• pp.199-204
• /
• 2021

Ultra-compact electric vehicles have narrow space for power conversion devices. This work presents schemes to achieve the high-power density of a low-voltage DC-DC converter (LDC): simplifying a converter structure by using sync-buck topology, applying a planar inductor using PCB winding, and applying a plate-type heat sink. The heat sink is placed between two PCBs, which increases the contact surface between the PCB and the heat-dissipating device. It enables the miniaturization of the converter to improve the conditions of heat radiation. The validity of the proposed scheme is verified through the experiment using a 500 W(12 V, 41.67 A) prototype with an input voltage range from 58 V to 84 V.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.1443-1448
• /
• 2009

Numerical analysis has been carried out to investigate air-side convective heat transfer characteristics in compact heat exchangers with continuous plate fins. Simulation results such as air flow and temperature distributions are presented, and heat transfer characteristics are compared for various inlet conditions. Results from various turbulence models are also compared for applicability. There is large difference between the local heat transfer coefficient distributions along the cylinder wall for circular tubes. Colburn j factors from the calculated results of circular and flat tubes in the heat exchangers are compared for various Reynolds number. The predicted results in this study can be applied to the optimal design of air conditioning system. with compact heat exchanger.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.3
• /
• pp.73-76
• /
• 2020

The physics-based compact gate leakage current noise models in nanoscale MOSFETs are developed in such a way that the models incorporate important physical effects and are suitable for circuit simulators, including QM (quantum-mechanical) effects. An emphasis on the trap-related parameters of noise models is laid to make the models adaptable to the variations in different process technologies and to make its parameters easily extractable from measured data. With the help of an accurate and generally applicable compact noise models, the compact noise models are successfully implemented into BSIM (Berkeley Short-channel IGFET Model) format. It is shown that the noise models have good agreement with measurements over the frequency, gate-source and drain-source bias ranges.

• Structural Engineering and Mechanics
• /
• v.10 no.4
• /
• pp.371-392
• /
• 2000

Application of "advanced analysis" methods suitable for non-linear analysis and design of steel frame structures permits direct and accurate determination of ultimate system strengths, without resort to simplified elastic methods of analysis and semi-empirical specification equations. However, the application of advanced analysis methods has previously been restricted to steel frames comprising only compact sections that are not influenced by the effects of local buckling. A concentrated plasticity method suitable for practical advanced analysis of steel frame structures comprising non-compact sections is presented in this paper. The pseudo plastic zone method implicitly accounts for the effects of gradual cross-sectional yielding, longitudinal spread of plasticity, initial geometric imperfections, residual stresses, and local buckling. The accuracy and precision of the method for the analysis of steel frames comprising non-compact sections is established by comparison with a comprehensive range of analytical benchmark frame solutions. The pseudo plastic zone method is shown to be more accurate and precise than the conventional individual member design methods based on elastic analysis and specification equations.

• Transactions of the Korean hydrogen and new energy society
• /
• v.13 no.4
• /
• pp.304-312
• /
• 2002

In this study, the performance of the $5Nm^3/hr$ compact type steam reformer which was developed for application of fuel cell or hydrogen station was evaluated in terms of gas process efficiency. For these purposes, reforming efficiency and total efficiency with system load change were analyzed. The reforming efficiency was calculated from the total molar flow of hydrogen output over total fuel flow input to the reformer and the burner on the higher heating value(HHV). In the case of the total efficiency, recovered heat at the heat recovery exchanger was considered. From the results, it was known that system performance was stable, because methane conversion showed the a slight decline which is about 2% though increasing system load to full. Reforming efficiency was increased from 20% to 58%, respectively as increasing system load from 10% to 90%. It was found that total efficiency was higher then reforming efficiency because of terms of heat recovered. As a results, it was known that total efficiency was increased form 75% to 83% at the 10% and 90% system load, respectively. From these results, it is concluded that compact steam reformer which is composed of stacking plate-type reactors is suitable to on-site hydrogen generator or to fuel cell application because of quick start within 1 hr and good performance.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.7 no.6
• /
• pp.31-37
• /
• 2008

In order to organize the Intelligent Transport System(ITS) as a communication equipment, the satellite and wireless system demand broadband characteristics for collecting information from the wide road. Band-pass filters (BPF) or broad BPFs used in such communication system are required for broadband characteristics. This paper presents a design of such broad BPF which can be used in the system. Designed BPF which was difficult to get broadband characteristics after realization, become possible to realize filter with broad bandwidth and compact structure using parallel coupled line. The designed filter achieved the insertion losses improved by 0.4 dB and the return losses improved by 17.4 dB respectively with 60% of bandwidth at the 5.8 GHz of the center frequency, respectively.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.2
• /
• pp.193-202
• /
• 2012

In this paper, we propose a new approach for compact range sensor system for real-time robot applications. Instead of using off-the-shelf camera and projector, we devise a compact system with a CMOS image-sensor and a DMD (Digital Micro-mirror Device) that yields smaller dimension ($168{\times}50{\times}60mm$) and lighter weight (500g). We also realize one chip hard-wired processing of projection of structured-light and computing the range by exploiting correspondences between CMOS images-ensor and DMD. This application-specific chip processing is implemented on an FPGA in real-time. Our range acquisition system performs 30 times faster than the same implementation in software. We also devise an efficient methodology to identify a proper light intensity to enhance the quality of range sensor and minimize the decoding error. Our experimental results show that the total-error is reduced by 16% compared to the average case.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1620-1622
• /
• 2003

Recently, as the technology for the development of high voltage power apparatus using SF6 gas has made remarkable progress, it became possible to develop more compact power apparatus adopting single body substation system. In these gas insulated power apparatus, it is impossible to achieve perfect and safe insulation using only SF6 gas, because some solid insulation parts should be installed to support current-carrying conductor parts for electrical and mechanical safety. When spacers were installed in SF6 gas insulation system, they were exposed to severe electrical intensification which could reduce system insulation performance and restrict the rated operating voltage So, it is necessary to clarify the dielectric characteristics of spacers by analytically and experimentally, in order to design and develop more compact and optimum gas insulated systems. In this paper, the field distribution of three-phase spacers were investigated using three dimensional electrostatic field analysis tool adopting BEM method. And the obtained results were compared to the conventional two dimensional computations. According to these three dimensional calculations, it was possible to find out weak points in the spacer more clearly and these results could be applied to design more compact and optimum three phase spacer developments.