• Journal of the Korean Graphic Arts Communication Society
• /
• v.24 no.2
• /
• pp.61-68
• /
• 2006

Rubber rollers in off-set printing process are one of the most important factor, transferring the ink and water to the plate. Each different roughness of roller surface and different rubber compounds could effect to ink transparency and printability. Three different rubber compounds (NBR, EPDM, PU) and each different roughness of roller surface would show us different result of ink transparency and density of actual printing result. There might be a differences from actual printing result not only the amount of transferred ink, but there is also some other point we should check it out. According to the result of this studies, we found that different rubber compounds and their surface roughness directly effect to the rate of ink transfer. It also shows that the amount of transferred ink is not even and stable amount what we expect to get optimum printability. To reach a targeted printability with rollers, firstly it is necessary to choose correct rubber compounds with certain purpose and the roughness of roller surface has to be as smooth as less than $5{\mu}m{\sim}7{\mu}m$.

• Journal of KIISE:Computer Systems and Theory
• /
• v.32 no.9
• /
• pp.465-474
• /
• 2005

For high density SoC design, on-chip communication based on bus interconnection encounters bandwidth limitation while an NoC(Network-on-Chip) approach suffers from unacceptable complexity in its Implementation. This paper introduces a new on-chip communication protocol, SNP (SoC Network Protocol) to overcome these problems. In SNP, conventional on-chip bus signals are categorized into three groups, control, address, and data and only one set of wires is used to transmit all three groups of signals, resulting in the dramatic decrease of the number of wires. SNP efficiently supports master-master communication as well as master-slave communication with symmetric channels. A sequencing rule of signal groups is defined as a part of SNP specification and a phase-restoration feature is proposed to avoid redundant signals transmitted repeatedly over back-to-back transactions. Simulation results show that SNP provides about the same bandwidth with only $54\%$ of wires when compared with AMBA AHB.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.17 no.4
• /
• pp.198-204
• /
• 2024

LDPC, known for its excellent error correction capability, has been adopted as the channel coding technique in the IRIG 106 standard, which is standard for data transmission methods in the aerospace field. Iterative codes such as LDPC require large block sizes and number of iterations in order to improve performance. However, large number of iterations induce computational complexity and power consumption. To solve these problems, this paper presents a parity check-based early stop algorithm that reduces the average number of iterations while maintaining the same performance. BER performance and iteration reduction amounts are compared between early stop algorithm and conventional method that has fixed number of iterations for various coding rate and information bit size defined in the IRIG 106 standard. Through simulation results, we confirmed required iteration numbers are reduced about 50% above without performance loss.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.16 no.2
• /
• pp.75-89
• /
• 1998

FM screening has been praised for its apparent resolution advantage over conventional AM screening. FM screening is also known for its criticalness of film output and difficulties in the proofing stage because of the microdot formation. However, FM screening is not a well understood process from press performance point of view. This study was carried out for the purposes of introducing the availability of hifi-offset printing to domestic printing industries and evaluating the print qualities between 300lpi AM screen and FM screen with the equivalent sized microdots to 4-5% dot area of the 300lpi AM screen, together with comparing with 175lpi AM screen representing a conventional printing. Solid density, dot gain, color gamut and some other quality properties were measured and discussed.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.16 no.2
• /
• pp.1-10
• /
• 1998

Even if some kinds of software for halftoning such as raster image process program are on the market, most of them couldn`t apply to the new laser gravure cylinder making machine because they are closed the source program. In order to develop new laser gravure engraving machine, we were investigated new suitable halftoning software based on the mapping and equal density expansion algorithm that we are mapped. As the results of actual practice with Microsoft Visiul C++2.0 in 133Khz 64M ram IBM personal computer, we found that the new software for halftone generation for laser gravure engraving machine are available in new machine, and easily load and processing the graphic image for gravure hardcopy.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.18 no.1
• /
• pp.121-139
• /
• 2000

This study is to test the possibility of applying the low-molecular weighted waste cellulase, which is produced in the process of cellulase production, to paper making. After experimenting on high-crystallized non-wood fibers with beating catalyst. I got the result that the condition for the optimal effect is temperature 40~6$0^{\circ}C$, the time 90min to 120min, pH 5.0 to 6.0, the enzyme contents 0.3% and that the effect of beating such as slight reduction of fiver viscosity, increase of water retention value(WRV) and shortening of fiber length was increased with waste cellulase. Through this process, the density, folding endurance, tensile strength and burst strength of paper was remarkably increased, which is inferred to result from the increased flexibility of fiber by individual characteristics of non-wood fiber, which was high-crystallized by penetrated low-molecular weight cellulases in the fiber.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1672-1675
• /
• 2003

Microstrip antennas have many applications in wireless communication system. This paper propose a analytical far-field pattern of radiation for application of the wireless communication. The triangular slot antenna fed by micorstrip line is proposed at resonance frequency 10 GHz. The simulation results of the electromagnetic field radiation pattern, S parameter, characteristic of input impedance are obtain by using the finite difference time domain (FDTD) method. The analytical space in FDTD analysis are $50{\times}171{\times}120$ cells with the cell dimension ${\Delta}x=0.152\;mm$, ${\Delta}y={\Delta}z=0.15\;mm$.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.3
• /
• pp.60-65
• /
• 1984

In this paper, we have used symmetrical GaAs/(Ga, Al) As DH-LED as a model for the optimization of frequency response which is the most important design parameter of the optical communication-LED. And optimum design parameters have been chosen to improve performance factors of the DH-LED by computer simulation. This is for the purpose of systematic consideration of the interrelation of the physical parameters such as impurity concentration of the active layer, thickness of the active layer, minority carrier lifetime, space charge capacitance and injected current density.

• The Journal of Korea Robotics Society
• /
• v.11 no.1
• /
• pp.19-25
• /
• 2016

In this paper, we propose a new method for improving the accuracy of localizing a robot to find the position of a robot in indoor environment. The proposed method uses visible light for indoor localization with a reference receiver to estimate optical power of individual LED in order to reduce localization errors which are caused by aging of LED components and different optical power for each individual LED, etc. We evaluate the performance of the proposed method by comparing it with the performance of traditional model. In several simulations, probability density functions and cumulative distribution functions of localization errors are also obtained. Results indicate that the proposed method is able to reduce localization errors from 7.3 cm to 1.6 cm with a precision of 95%.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.3 no.3
• /
• pp.3-7
• /
• 2010

As the distance between signal lines in memories of high density ICs like SoCs decreases rapidly, failure occurs more frequently and effective memory test techniques are needed. In this paper, a new SRAM structure is proposed to decrease test complexity and test time for embedded DRAMs. In the presented technique, because memory test can be handled as a single port testing and read-write operation is possible at dual port without high complexity, test time can be much reduced.