• Smart Structures and Systems
• /
• v.24 no.5
• /
• pp.641-648
• /
• 2019

The authors investigate the feasibility of applying a vision-based displacement-measurement technique in the characterization of a SMA damper recently introduced in the literature. The experimental campaign tests a steel frame on a uni-axial shaking table driven by sinusoidal signals in the frequency range from 1Hz to 5Hz. Three different cameras are used to collect the images, namely an industrial camera and two commercial smartphones. The achieved results are compared. The camera showing the better performance is then used to test the same frame after its base isolation. U-shaped, shape-memory-alloy (SMA) elements are installed as dampers at the isolation level. The accelerations of the shaking table and those of the frame basement are measured by accelerometers. A system of markers is glued on these system components, as well as along the U-shaped elements serving as dampers. The different phases of the test are discussed, in the attempt to obtain as much possible information on the behavior of the SMA elements. Several tests were carried out until the thinner U-shaped element went to failure.

• Nuclear Engineering and Technology
• /
• v.54 no.12
• /
• pp.4652-4659
• /
• 2022

Among the detector materials available at room temperature, thallium bromide (TlBr), which has a relatively high atomic number and density, is widely used for gamma camera imaging. This study aimed to verify the usefulness of TlBr through quantitative evaluation by modeling detectors of various compound types using Monte Carlo simulations. The Geant4 application for tomographic emission was used for simulation, and detectors based on cadmium zinc telluride and cadmium telluride materials were selected as a comparison group. A pixel-matched parallel-hole collimator with proven excellent performance was modeled, and phantoms used for quality control in nuclear medicine were used. The signal-to-noise ratio (SNR), contrast to noise ratio (CNR), sensitivity, and full width at half maximum (FWHM) were used for quantitative analysis to evaluate the image quality. The SNR, CNR, sensitivity, and FWHM for the TlBr detector material were approximately 1.05, 1.04, 1.41, and 1.02 times, respectively, higher than those of the other detector materials. The SNR, CNR and sensitivity increased with increasing detector thickness, but the spatial resolution in terms of FWHM decreased. Thus, we demonstrated the feasibility and possibility of using the TlBr detector material in comparison with commercial detector materials.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2529-2532
• /
• 2003

The quality of agricultural products is represented a degree of freshness and a special qualify that has a close relation to commercial value. To grade tomatoes, it used to nondestructive equipment of a charge-coupled device(CCD) camera and near-infrared(NIR) spectrum analysis method. The NIR spectrum analysis method is used to determine internal qualities such as a brix and an acidity. The CCD camera is used to measure external qualities like color and a size of tomatoes. This paper explaines the structure and movement of the automatic grade system and applies the algorithm for deformed tomtatoes and characteristics of tomatoes through image processing to the grade system.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.9
• /
• pp.2191-2204
• /
• 1993

A sensor system has been developed to measure the posture(position and orientation) of mobile robots working in industrial environments. The proposed sensor system consists of a CCD camera, retro-reflective landmarks, a strobe unit and an image processing board. The proposed hardware system can be built in economic price compared to commercial vision systems. The system has the capability of measuring the posture of mobile robots within 60 msec when a 386 personal computer is used as the host computer. The experimental results demonstrated a remarkable performance of the proposed sensor system in the posture measurement of mobile robots - the average error in position is less than 3 mm and the average error in orientation is less than 1.5.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.6
• /
• pp.57-64
• /
• 1999

Initial flame development and propagation were visualized under the new ignition system developed to estimate the effects of ignition characteristics on the engine performance in a port injection SI engine. Effects of intake air flow characteristics were also investigated by three different kinds of the swirl control valve. Experiments were performed in an optical single cylinder engine modified form a commercial engine. Flame images were captured through the quartz window mounted in the piston by the high speed video camera and analyzed to compare initial flame development. Results show that IMEP tends to rise slightly as the ignition duration gets longer. The direction of flame propagation is decisively governed by the in-cylinder flow motion. Every flame grows toward the exhaust valve forming a kind of turbulent flame. Initial flame propaagation characteristics are very similar to ones analyzed form pressure data.

• Proceedings of the KSRS Conference
• /
• 2002.10a
• /
• pp.578-578
• /
• 2002

Thermal infrared imaging is a highly promising technology for condition monitoring and predictive maintenance of electronic, electrical and mechanical elements in nuclear power plants. However, conventional low-cost infrared imaging systems suffer from poor spatial resolution compared to commercial CCD cameras. This paper describes an approach to enhance inspection performances for calandria reactor area of Wolsung nuclear power plant through the technique of superimposing thermal infrared image into real CCD image. In the occurrence of thermal abnormalities on observation points and areas of calandria reactor area, unusual hot image taken from thermal infrared camera is mapped upon real CCD image. The performance of the technique has been evaluated in the experiment carried out at Wolsung nuclear power plant in the overhaul period. The results show that localizations of thermal abnormalities on calandria reactor face can be estimated accurately.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.33 no.1
• /
• pp.31-43
• /
• 2015

This study had been aimed to conduct the camera calibration on VLBI antenna in the Space Geodetic Observation Center of Sejong City with a low-cost digital camera, which embedded in a mobile phone to determine the three-dimension position coordinates of the VLBI antenna, based on stereo images. The initial values for the camera calibration have been obtained by utilizing the Direct Linear Transformation algorithm and the commercial digital photogrammetry system, PhotoModeler $Scanner^{(R)}$ ver. 6.0, respectively. The accuracy of camera calibration results was compared with that the camera calibration results, acquired by a bundle adjustment with nonlinear collinearity condition equation. Although two methods showed significant differences in the initial value, the final calibration demonstrated the consistent results whichever methods had been performed for obtaining the initial value. Furthermore, those three-dimensional coordinates of feature points of the VLBI antenna were respectively calculated using the camera calibration by the two methods to be compared with the reference coordinates obtained from a total station. In fact, both methods have resulted out a same standard deviation of $X=0.004{\pm}0.010m$, $Y=0.001{\pm}0.015m$, $Z=0.009{\pm}0.017m$, that of showing a high degree of accuracy in centimeters. From the result, we can conclude that a mobile phone camera opens up the way for a variety of image processing studies, such as 3D reconstruction from images captured.

• Journal of electromagnetic engineering and science
• /
• v.16 no.4
• /
• pp.214-218
• /
• 2016

In this paper, we present an ambient light backscatter communication design that enables Internet of Things (IoT) devices to communicate through the backscattering ambient light emitted from lighting infrastructure or sunlight. The device can selectively modulate ambient light by switching a liquid crystal display (LCD) shutter located on its surface, so that a nearby smart device, which includes a photodiode or a camera, can demodulate this backscattered light information. To verify the practicality of the proposed concept, we design an IoT device equipped with a commercial LCD shutter and a microcontroller. Our device produces ambient light backscattered data at a speed of 100 bps, and these data are successfully decoded by a commercial photodiode module 10 cm away from the IoT device. We believe that our ambient light backscatter communication design is appropriate for implementation in various IoT applications.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.11
• /
• pp.1872-1879
• /
• 1989

In this paper, we implement optical holographic associative memory based on the two-dimensional neural network model by using commercial LCTV as a spatial light modulator. The system consists of the simple Vander Lugt correlator utilizing plane Fourier hologram and the pinhole array. The associated output signal is detected on a two-dimensional CCD camera and electronically thresholded and fed back to the input plane of the system. Through the experimental demonstration of nonlinear holographic associative memory, it is suggested that commercial LCTV can be used as a new coherent spatial light modurator.

• Journal of the Korean Society of Combustion
• /
• v.20 no.4
• /
• pp.1-9
• /
• 2015

The object of this study is a deriving the relations according to the measuring locations between the chemiluminescence and the flame state at commercial burner. In this study, the flame chemiluminescence of the flame of commercial burner is measured using a photomultiplier tube and the optical band-pass filter. In addition, the contour of the chemiluminescence of the flame is measured using the common CCD camera and the optical band-pass filters, and the acquired images is converted by the simple image processing as a matrix form. The results showed that certain relationship between optical data and equivalence ratio exists, and the contour according to the measuring location of the flame chemiluminescence is different by equivalence ratio.