• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.8
• /
• pp.1259-1265
• /
• 2003

We present a new post-fabrication frequency tuning method for laterally driven electrostatic microresonators using a DC-biased electrostatic comb array of linearly varied finger-length. The electrostatic tuning force and the equivalent stiffness, adjusted by the DC-biased tuning-comb array, have been formulated as functions of geometry and DC tuning voltage. A set of frequency-turnable microresonators has been designed and fabricated by 4-mask surface-micromachining process. The resonant frequency of the microfabricated microresonator has been measured for a varying tuning voltage at the reduced pressure of 1 torr. The maximum 3.3% reduction of the resonant frequency is achieved at the tuning voltage increase of 20V.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.2
• /
• pp.142-150
• /
• 2004

A preliminary study of the behavior of ultrasonic guided wave mode in a pipe using a comb transducer for maintenance inspection of power plant facilities has been verified experimentally. The mode identification has been carried out in a pipe using the time-frequency analysis methods such as the wavelet transform(WT) and the short time Fourier transform (STFT), compared with theoretically calculated group velocity dispersion curves for longitudinal and flexural modes. The results are in good agreement with analytical predictions and show the effectiveness of using the time-frequency analysis method to identify the individual modes. It was found out that the longitudinal mode(0,1) is less affected by mode conversion compared with the other modes. Therefore, L(0,1) is selected as an optimal mode for the evaluation of the surface defect in a pipe.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.3
• /
• pp.427-430
• /
• 2020

The multi-channel analog signal to digital signal conversion is increasing in the field of IoT and medical measurement equipments. It has chip area and power consumption constraints to use a few single or 2_channel ADC for multi_channel application. This paper described to design and implement a proposed comb filter for multi-channel, 24bit ADC. The function of proposed comb filter is verified by matlab simulation and the FPGA test board. It was fabricated using SK Hynix 0.35㎛ CMOS standard process. The performance and chip size is compared with the existing design method that uses integrator/differentiator and FIR construction. The proposed comb filter is expected to use the IoT product and medical measurement equipments that require multi-channel, low power consumption and small hardware size.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.14 no.6
• /
• pp.699-712
• /
• 1989

This paper describes a method of Korean speech synhes is using format VOCODER. The parameters of speech synthes is are a follows, 1) format F1, F2, and F3 by spectrum moment method and F4, F5 using the length of vocal tract. 2) pitch frequencies obtained by optimu, Comb method using AMDF. 3) short time average energy and short time mean amplitude. 4) The decision method of bandwidth reportd by Fant. 5) voicde/unvoiced discrimination using zerocrossing. 6) excitation wave reported by Rosenberg. 7) gaussian white noise. Synthesis results are in fairly good agreement with original speech.

• Polymer(Korea)
• /
• v.34 no.6
• /
• pp.501-506
• /
• 2010

Natural chitosan has high molecular weight and the poor solubility in water. Water-soluble chitosan with low molecular weight was prepared by the hydrolysis method. In order to develop an efficient gene delivery carrier, chitosan was conjugated with lipoic acid to form the comb-type copolymer. The copolymer with the amphiphilic property formed the self-assembled nanoparticles in the aqueous solution. The average size of nanoparticles was 217.6 nm and the average size of nanoparticles/DNA complex was 170 nm. New chitosan-lipoic acid copolymer showed the low cytotoxicity and 10 times higher transfection efficiency than that of the pure chitosan.

• Proceedings of the IEEK Conference
• /
• summer
• /
• pp.199-203
• /
• 2004

In this paper, we only describe the digital block of two-channel 18-bit analog-to-digital (A/D) converter employing sigma-delta method and xl28 decimation. The device contains two fourth comb filters with 1-bit input from sigma­delta modulator. each followed by a digital half band FIR(Finite Impulse Response) filters. The external analog sigma-delta modulators are sampled at 6.144MHz and the digital words are output at 48kHz. The fourth-order comb filter has designed 3 types of ways for optimal power consumption and signal-to-noise ratio. The following 3 digital filters are designed with 12tap, 22tap and 116tap to meet the specification. These filters eliminate images of the base band audio signal that exist at multiples of the input sample rate. We also designed these filters with 8bit and 16bit filter coefficient to analysis signal-to-noise ratio and hardware complexity. It also included digital output interface block for I2S serial data protocol, test circuit and internal input vector generator. It is fabricated with 0.35um HYNIX standard CMOS cell library with 3.3V supply voltage and the chip size is 2000um by 2000um. The function and the performance have been verified using Verilog XL logic simulator and Matlab tool.

• Korean Journal of Materials Research
• /
• v.15 no.1
• /
• pp.54-60
• /
• 2005

Recently a lots of problems have observed in high densified and high integrated electronic components. One of them is ion migration phenomena, which induce the electrical short of electrical circuit. ion migration phenomena has been observed in the field of exposing the specific environment and using for a long tin e. This study was evaluated the generation time of ion migration and was investigated properly test method through water drop test and high temperature high humidity test. Also we observed direct causes and confirmed generation mechanism of dendritic growth as we reproduced the ion migration phenomena. We utilized PCB(printed circuit board) having a comb pattern as follows 0.5, 1.0, 2.0 mm pattern distance. Cu, SnPb and Au were electroplated on the comb pattern. 6.5 V and 15 V were applied in the comb pattern and then we measured the electrical short time causing by ion migration. In these results, we examined a difference of ion migration time depending on pattern materials, applied voltage and pattern spacing of PCB conductor.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.147.2-148
• /
• 2016

Light management technology is very important for thin film solar cells, which can reduce optical reflection from the surface of thin film solar cells or enhance optical path, increasing the absorption of the incident solar light. Using proper light trapping structures in hydrogenated amorphous silicon (a-Si:H) solar cells, the thickness of absorber layers can be reduced. Instead, the internal electric field in the absorber can be strengthened, which helps to collect photon generated carriers very effectively and to reduce light-induced loss under long-term light exposure. In this work, we introduced a chemical etching technology to make honey-comb textures on glass substrates and analyzed the optical properties for the textured surface such as transmission, reflection and scattering effects. Using ray optics and finite difference time domain method (FDTD) we represented the behaviors of light waves near the etched surfaces of the glass substrates and discussed to obtain haze parameters for the different honey-comb structures. The simulation results showed that high haze values were maintained up to the long wavelength range over 700 nm, and with the proper design of the honey-comb structure, reflection or transmission of the glass substrates can be enhanced, which will be very useful for the multi-junction (tandem or triple junction) thin film a-Si:H solar cells.

• Journal of Conservation Science
• /
• v.30 no.4
• /
• pp.329-334
• /
• 2014

A scientific analysis of ancient textiles provides significant data to understand weaving techniques and culture of textiles in each region and charateristics of materials used at that time. In addition, species identification of waterlogged wooden objects is a scientific analysis method that allow us to verify information of relation of foreign species trade and exchange, of preferable species through kinds of wooden products, and of forest environment as well as method setting of conservation. As a result of a species analysis about historical textiles and a wooden comb in a bronze bowl that were excavated from Hapgang-ri, Dong-Myun, Yungi-gun, Chungcheongnam-do, Textile1 and Textile3 are identified as Urticacese Boehmeri nivea ; ramie, Textie2 is identified as Malvaceae Gossypium herbaceum, and a wooden comb is identified as Betulaceae Betula spp. It is expected that this result will help to make further comparative studies, identifying species of textiles and trees of ancient times.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.11
• /
• pp.2347-2354
• /
• 2012

On Android environment, program development is conducted with JAVA SDK. However, using JAVA, it is operated over virtual machine which shows lower performance in terms of speed than traditional C language programming. The method writes program in C language, which conducts operation efficiently. In the paper, we implement multiplication using NDK and SDK to analyze the public key cryptography over Android environment. In case of SDK, we used BigInteger package and in case of NDK, we used Comb method. Moreover, execution time of arithmetic, branch and call operations over Android environment is compared to understand performance enhancement using NDK package.