• Journal of Magnetics
• /
• 제21권1호
• /
• pp.12-19
• /
• 2016

The <100> oriented $Fe_{83}Ga_{17}$ alloys with various contents of NbC or B were prepared by directionally solidification method at the growth rate of $720mm{\cdot}h^{-1}$. With a small amount of precipitates, the columnar grains grew with cellular mode during directional solidification process, while like-dendrite mode of grains growth was observed in the alloys with higher contents of 0.5 at% due to the dragging effect of precipitates on the boundaries. The NbC precipitates disperse both inside grains and along the boundaries of $Fe_{83}Ga_{17}$ alloys with NbC addition, and the Fe2B secondary phase particles preferentially distribute along the grain boundaries in B-doped alloys. Precipitates could affect grain growth and improved the <100> orientation during directional solidification process. Small amount of precipitate element addition slightly increased the magnetostrictive strain, and a high value of 335 ppm under pre-stress of 15 MPa was achieved in the alloys with 0.1 at% NbC. Despite the fact that the effect on magnetic induction density of small amount of precipitates could be negligible, the coercivity markedly increased with addition of precipitate element for $Fe_{83}Ga_{17}$ alloy due to the retarded domain motion resulted by precipitates.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제31권1호
• /
• pp.1-7
• /
• 2009

Purpose: The purpose of this study is to investigate the therapeutic use of Hepatocyte growth factor(Adv.CMV.HGF) in temporomandibular joint disc defect. Materials and methods: Twelve New Zealand white rabbits, weighing 2.5 - 3.0 kg, were used in this experiment. Defects(2 mm in diameter) were created in their TMJ discs. Recombinant Adv.CMV.HGF with gelatin sponge($Gelfoam^{(R)}$) as carrier was implanted in the defects. We divided the rabbits into four batches according to the duration of the implantation - of 1, 4, 8, 12 weeks - and both left and right TMJ of each rabbit in all groups were used in the research : left joints were used as experiment group and right were control group. Each batch of rabbits was killed one, four, eight and twelve weeks after the experimentation respectively, and called Group A, B, C, and D. (Group A = 1 wk, B = 4 wks, C = 8 wks, and D = 12 wks) Results: The experimental group showed a significant increase in the number of chondroblasts and active cell differentiation at the margin of the defects. Compared to the control group, in the experiment group chondroblasts increased and chondrocytes showed a columnar arrangement, which is witnessed at the time of cell differentiation. Conclusion: This study supports the case that Avd.CMV.HGF may be useful in the repair of articular disc of the rabbit TMJ.

• Composites Research
• /
• 제31권2호
• /
• pp.43-50
• /
• 2018

화학기상증착 탄화규소(CVD-SiC)의 높은 증착율과 우수한 굽힘강도 특성을 얻기 위해 증착온도에 대한 영향을 연구하였다. Hot-wall CVD 방법으로 메틸트리클로로실란(MTS : $CH_3SiCl_3$)을 이용하여 $1250{\sim}1400^{\circ}C$ 조건에서 제조된 탄화규소는 $95.7{\sim}117.2{\mu}m/hr$ 정도의 증착율을 보였다. 율속반응은 $1300^{\circ}C$ 미만에서는 표면반응, 그 이상의 온도에서는 물질전달 지배영역 특성을 나타내었다. Arrhenius plot을 통해 계산한 활성화 에너지는 각각 11.26 kcal/mole과 4.47 kcal/mole이였다. 증착온도별 표면 형상은 $1250^{\circ}C$ pebble에서 $1300^{\circ}C$ facet 구조로 변하였고, $1350^{\circ}C$ 이상에서는 multi-facet 구조를 나타내었다. 단면 형상은 $1300^{\circ}C$ 이하에서 columnar, $1350^{\circ}C$ 이상에서 isometric 구조를 보였다. 결정상은 모두 ${\beta}$-SiC로 확인되었지만 결정성장 방향은 $1250^{\circ}C$ (111)에서 $1300^{\circ}C$ 이상부터 (220) peak가 관찰되었으며, $1400^{\circ}C$에서는 (220)으로 완전히 변함을 알 수 있었다. 굽힘강도 특성은 증착온도가 증가할수록 치밀화되고, columnar에서 isometric 조직으로 변화되면서 $1350^{\circ}C$에서 최대값을 나타내었으며, $1400^{\circ}C$에서는 grain size 증가와 결정성장 방향이 최밀충진면인 (111)에서 (220)으로 완전히 변하면서 감소된 것으로 보인다.

• 한국결정성장학회지
• /
• 제29권6호
• /
• pp.308-316
• /
• 2019

전자빔 물리기상증착기술(EBPVD)은 주상형 성장거동과 같이 고온에서의 구조 안정성에 기여할 수 있는 특성으로 인해 터빈블레이드 등과 같은 항공기 엔진 고온부품의 열차폐 코팅(TBC) 제조기술로 개발되어 상용화된 기술이다. 전자빔 증착으로 열·기계적 특성이 상용화 가능한 수준에 만족하는 고품질 열차폐 코팅제조를 위해서는 성장거동, 균일두께형성 등과 같은 구조적 요소의 제어가 반드시 수반되어야 한다. 본 연구에서는 실품형상에 근사한 터빈 블레이드 mock-up에 대한 기하학적 코팅인자 조건에 따른 7YSZ(7 wt% 이트리아 안정화 지르코니아) 열차폐 코팅의 성장거동과 구조변화를 고찰하였으며, 전산모사 기법을 활용한 기하학적 코팅인자 조건에 따른 코팅성장거동 모델링을 수행하여 실제 코팅결과와 비교하였다.

• 한국패류학회지
• /
• 제24권3호
• /
• pp.229-241
• /
• 2008

TBTCl에 36주 동안 노출된 대복(Gomphina veneriformis)의 성장과 외투막의 조직학적 변화를 관찰하였다. 대복의 성장은 모든 실험구의 개체들이 12주 이후부터 대조구에 비해 유의적인 차이를 보이며 감소하였다(p < 0.05). 대복의 외투막은 가장자리에 4 개의 주름 (내부 안쪽, 외부 안쪽, 가운데, 바깥쪽)을 가지며, 단층의 원주형 상피층이 결합조직층을 둘러싸고 있는 구조였다. 대복의 외투막은 TBTCl 노출 12주 이후부터 혈림프동이 확장과 근섬유 다발의 분절이 관찰되었다. 노출 20주에는 내부상피층에 존재하는 점액세포들이 대조구보다 유의적인 차이를 보이며 감소하였지만(p < 0.05), 외투막 가장자리에 존재하는 주름들에서는 노출 12주까지 감소하였던 점액세포가 증가하면서 AB-PAS (pH 2.5) 반응시 보라색 (2587c)으로 관찰되는 점액물질이 관찰되었다. 이후 노출 28주에는 가운데 주름 부위의 안쪽 분지에서 상피세포의 변형이 관찰되었고, 외부 상피층에서는 상피세포의 부분적인 파괴가 관찰되었다. 실험 종료시기인 36주에는 바깥쪽 주름 부위에 호산성 과립들이 관찰되었으며, 가운데 주름부위의 바깥 분지에서 상피세포의 변형과 파괴로 인한 상피층의 붕괴가 관찰되었다. 또한 외부 상피층의 상피세포들은 입방형 또는 편평형으로의 변화와 함께 부분적인 상피층의 붕괴가 나타났고, 그로 인하여 상피층의 두께가 감소하였다. 따라서 섬모의 탈락과 점액세포의 감소 그리고 상피층의 파괴는 외투강 정화 기능의 장애로 인한 먹이 섭식의 장애를 유발할 것으로 생각되며, 특히 외투막 가장자리에 존재하는 주름들의 구조적인 변화는 각피층 형성을 억제하여 패각 성장 장애의 직접적인 원인으로 생각되어진다.

• Nuclear Engineering and Technology
• /
• 제41권2호
• /
• pp.149-154
• /
• 2009

The microstructure, the corrosion behavior and the oxide properties were examined for Zr-1.5Nb-0.4Sn-0.2Fe-0.1Cr (HANA-4) alloys which were subjected to two different final annealing temperatures: $470^{\circ}C$ and $570^{\circ}C$. HANA-4 was shown to have $\ss$-enriched phase with a bcc crystal structure and Zr(Nb,Fe,Cr)$_2$ with a hcp crystal structure with $\ss$-enriched phase being more frequently observed compared with Zr(Nb,Fe,Cr)$_2$. The corrosion rate of HANA-4 was increased with an increase of the final annealing temperature in the PWR-simulating loop, $360^{\circ}C$ pure water and $400^{\circ}C$ steam conditions, which was correlated well with a reduction in the size of the columnar grains in the oxide/metal interface region. The oxide growth rate of HANA-4 was considerably affected by the alloy microstructure determined by the final annealing temperature.

• 마이크로전자및패키징학회지
• /
• 제11권3호
• /
• pp.63-70
• /
• 2004

The structural, electrical properties of $(Ba, Sr)TiO_3[BSTO]/RuO_2$ thin films were examined by the addition of amorphous BSTO layer between crystlline BSTO film and $RuO_2$ substrate. We prepared BSTO films with double-layered structure, that is, amorphous layers deposited at $60^{\circ}C$ and crystalline films. Crystalline films were prepared at 550 on amorphous BSTO layer. The thickness of the amorphous layers was varied from 0 to 170 nm. During the deposition of crystalline films, the crystallization of the amorphous layers occurred and the structure was changed to circular while crystalline BSTO films showed columnar structure. Due to insufficient annealing effect, amorphous BSTO phase was observed when the thickness of the amorphous layers exceeded 30 nm. Amorphous BSTO layer could also prevent the formation of oxygen deficient region in $RuO_2$ surface. Leakage current of total BSTO films decreased with increasing amorphous layer thickness due to structural modifications. Dielectric constant showed maxi-mum value of 343 when amorphous layer thickness was 30 nm at which the improvement by grain growth and the degradation by amorphous phase were balanced.

• Journal of Welding and Joining
• /
• 제6권4호
• /
• pp.16-26
• /
• 1988

The effect of carbon content on hot cracking of welded carbon steel was investigated Eight steel plates whose carbon content range from 0.02 to 0.23 percent were welded by autogeous gas tungsten are process. Constant strain was applied to the hot crack test specimen under the strain rate of 0.15 mm per second during welding. The hot cracking susceptibility ws high in the rnage of 0.02-0.05 and 0.12-0.23 percent carbon contents. The critical carbon content immune to hot cracking is in the range from 0.07 to 0.12 percent carbon. By electron probe microanalyser, amanganese segregation was not seen significantly in the whole carbon range. But segregation of silicon was higher in the region of low carbon contents. However, sulphur was segregated remarkably in the region betwen 0.18 and 0.23 percent carbon by peritectic reaction. Very smal lamount of dnedritic structure was observed in the region from 0.02 to 0.05 percent carbon by peritectic reaction. Very small amount of dendritic structure was observed in the region from 0.02 to 0.05 percent carbon but the predominant solidification structure was smooth by cellular growth. The higher the carbon content is, the more the columnar dendritic structure was observed.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 춘계학술대회논문집
• /
• pp.51-56
• /
• 2005

For a fire cause judgement this paper describes the short circuit characteristics of a electric wire through the cross section analysis under ac condition. The cower wires prepared for the experiment were 1.2mm, 1.6mm, and 2.0mm in diameter. Through the cross section analysis(CSA), it was confirmed that the dendrite structure grew at the angle of about $40^{\circ}\;or\;60^{\circ}$ when the fusing current was applied to the wires. The larger the fusing current is, the more decreased the growth angle of the dendrite structure is. It was confirmed that the dendrite structure was arranged like the columnar structure. In this paper, the characteristics analysis of short circuit was carried out in the range of transient duration and the correlation constant k was investigated by measuring the short circuit duration and the fusing current.

• 한국주조공학회지
• /
• 제3권1호
• /
• pp.3-12
• /
• 1983

The influence of columnar dendirtes on the mechanical properties of Al-1% Cu alloys as unifirectionalloy solidified under the conditions of controlled crystal growth rate (R) and temperature gradient (G) was investigated. And the change of metallography and mechanical properties when unifirectionalloy solidified alloys and cast alloys were cold-rolled from 10% to 90% in reduction ratio was studied. The results are as follows: 1. The elongation and yield strength of unifirectionalloy solidified alloy are higher then those of cast alloy, but there is a little decrease in ultimate tensile strength. 2. The metallography and mechanical properties are changeable with the primary arm spacings when the unidirectionalloy solidified alloys were cold-rolled from 10% to 90% in reduction ratio. An alloy with larger primary arm spacings was easily changeable in metallography and mechanical properties when it was cold-rolled. 3. The tensile strength of transversely cold-rolled to 90% in reduction ratio was higher then that of longitudionalloy cold-rolled to 90% in reduction ratio. In the case, the fractorgraphs of fractured surface showed that the cast alloy and the unifirectionalloy solidified alloy was ductile-fractured, but the surface of transversely cold-rolled to 90% reduction of unidirection alloy solidified was slip plane qracture.