• Journal of Technologic Dentistry
• /
• v.38 no.4
• /
• pp.281-290
• /
• 2016

Purpose: The increased aesthetic requirements and demands of patients have resulted in the developments of coloring liquid for zirconia. Methods: In this study, zirconia block was dipped into $Fe(NO_3)_3$solution, which showed a color and then concentration of $Fe(NO_3)_3$and zirconia's color and physical properties depending on the dipping time were observed and compared with exclusive coloring solutions. As the result, the following conclusions were obtained. Results: When compared with the specimens that were colored using exclusive solutions, $L^*$ value rose overall depending on the concentration of $Fe(NO_3)_3$and $a^*$ value was red in the form of (+) in all the specimens. Also, $b^*$ value was in the form of (+) at 0.5 to $1{\ss}fl$, but was in the form of (-) at 1.5 to $2{\ss}fl$. The dipping time did not highly influence $L^*$ value, but $a^*$ value and $b^*$ value were directly opposite to the specimens, which were not colored, except the sample that was dipped for only 2 seconds. When compared with exclusive coloring solutions, $Fe(NO_3)_3$had the most similar color at 0.5 to $1{\ss}fl$ and the longer the coloring time, the higher the rate of color change became. In relation to the density change depending on the addition of $Fe(NO_3)_3$, there was the lowest density at $2{\ss}fl$ and the density was increased in the specimens that were not colored. Conclusion: These results show that $Fe(NO_3)_3$solution can be used to make colored zirconia. It is expected that newly made colored zirconia can be used in clinical practice because the colored zirconia not only possesses the mechanical properties that all ceramic core material should have but also was biocompatible to a living cells.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.40 no.2
• /
• pp.203-214
• /
• 2014

We measured the contact dermatitis-causing substances concentrations in 28 commercial oxidative hair-coloring products. This study was aimed to provide the fundamental data about oxidative hair-coloring products. We selected 10 oxidation dyes (p-phenylenediamine, toluene-2,5-diamine, m-phenylenediamine, nitro-p-phenylenediamine, p-aminophenol, m-aminophenol, o-aminophenol, p-methylaminophenol, N,N'-bis(2-hydroxyethyl)-p-phenylenediamine sulfate, 2-methyl-5-hydroxyethylaminophenol) and 4 heavy metal (nikel; Ni, chromium; Cr, cobalt; Co, copper; Cu) as contact dermatitis-causing substances. To identify 10 oxidation dyes, hexane-2% sodium sulfite was used for the rapid and simple extraction and ultra performance liquid chromatography (UPLC) analysis was used for simultaneous analysis in 12 minutes. 10 oxidative dyes were detected as indicated on the product packaging and each concentration was lower than prescribed upper concentration limit by pharmaceutical manufacturing standards. And we analysed inductively coupled plasma-optical emission spectrophotometer (ICP-OES) for content search of heavy metal after microwave digestion. The heavy metal average concentration in oxidative hair-coloring products was 0.572 ${\mu}g/g$ for Ni, 3.161 ${\mu}g/g$ for Cr, 2.029 ${\mu}g/g$ for Co, 0.420 ${\mu}g/g$ for Cu, respectively. The average of concentration in powder type (henna) was higher than those of other foam and cream type oxidative hair-coloring products as follows; 1.800 ${\mu}g/g$ for Ni, 10.127 ${\mu}g/g$ for Cr, 7.082 ${\mu}g/g$ for Co, 1.451 ${\mu}g/g$ for Cu. Hair coloring products were classified into the six colors - black, dark brown, brown, dark brown, light brown, red brown and analyzed. Brown color had the highest average concentration of Co and the others had the highest average concentration of Cr.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.24 no.3
• /
• pp.73-80
• /
• 1998

This Study was performed to get the suitable oil dispersion agent by assessment of color strength of organic pigment in non-aqueous systems. Organic pigment is used as a color expression material with other body pigments in the make-up products. But occasionally aggregation or agglomeration occurs for the lack of affinity with medium, This function is the cause of disturbing homogeneous dispersion, and then bring about an instability of products. Our study, research of dispersion mechanism between the pigment and oil phase, has been executed to solve this problem, and find a oil dispersion agent having optimum dispersion condition. Generally dispersion is related to between the solid-liquid mutual properties and electrical phenomena associated with solid-liquid interface. This factor is determined to input energy, milling time, optical properties, particle size, rheological properties, etc. Ideal dispersion state is told that coloring primary solid particle is homogeneously dispersed in medium. Good dispersed colorants are strongly and clearly appeared. We are already known that the particle size of organic pigment, chemical properties and viscosity of medium, refractive index. Consequently We determine the affinity of medium and organic pigment by measuring of color strength in the same mechanical condition. UV-VISIBLE RECORDING SPECTRO PHOTOMETER is used for measuring apparatus. We can decided the dispersion level of oil dispersion agent by measuring absorbance of color strength in the visible range that diluted medium for colloid colorant particles.

• Journal of Applied Biological Chemistry
• /
• v.50 no.4
• /
• pp.221-226
• /
• 2007

The high molecular-weight mucilage extracted and purified from cactus fruit of Opuntia ficus-indica var. Saboten was degraded by the cell-free culture filtrate of a fungus isolated from soil. TLC analysis of the polymeric mucilage after incubation with the fungal culture filtrate confirmed its degradation. When the degradation products were tested for their qualitative reactions with ninhydrin and phenol-sulfuric acid, only phenol-sulfuric acid gave positive development, and ninhydrin did not show any observable color reaction. This coloring reaction suggested the presence of a carbohydrate without an amino group within the mucilage. Analyses by HPLC and liquid gel permeation chromatography on sephadex G-100 also provided additional information on degradation of the mucilage by the fungal culture filtrate. The sequences of ITS-5.8S rDNA from the fungal isolate that was cultivated for the preparation of mucilage-degrading enzyme showed 99% similarity to those of Pestalotiopsis aquatica.

• The Journal of Advanced Prosthodontics
• /
• v.8 no.1
• /
• pp.37-42
• /
• 2016

PURPOSE. This study investigated the effect of amount of thickness reduction on color and translucency of dental monolithic zirconia ceramics. MATERIALS AND METHODS. One-hundred sixty-five monolithic zirconia specimens ($16.3mm{\times}16.3mm{\times}2.0mm$) were divided into 5 groups (Group I to V) according to the number of A2-coloring liquid applications. Each group was then divided into 11 subgroups by reducing the thickness up to 1.0 mm in 0.1-mm increments (Subgroup 0 to 10, n=3). Colors and spectral distributions were measured according to CIELAB on a reflection spectrophotometer. All measurements were performed on five different areas of each specimen. Color difference (${\Delta}E^*{^_{ab}}$) and translucency parameter (TP) were calculated. Data were analyzed using one-way ANOVA and multiple comparison $Scheff{\acute{e}}$ test (${\alpha}=.05$). RESULTS. There were significant differences in CIE $L^*$ between Subgroup 0 and other subgroups in all groups. CIE $a^*$ increased (0.52<$R^2$<0.73), while CIE $b^*$ decreased (0.00<$R^2$<0.74) in all groups with increasing thickness reduction. Perceptible color differences (${\Delta}E^*{^_{ab}}$>3.7) were obtained between Subgroup 0 and other subgroups. TP values generally increased as the thickness reduction increased in all groups ($R^2$>0.89, P<.001). CONCLUSION. Increasing thickness reduction reduces lightness and increases a reddish, bluish appearance, and translucency of monolithic zirconia ceramics.

• Journal of the Korean Chemical Society
• /
• v.8 no.2
• /
• pp.47-56
• /
• 1964

When a developed paper partition chromatogram was irradiated by means of the pneumatic tube system of the Korean research reactor (neutron flux: 1.5 ${\times}10^{12}n/cm^2$sec.) the qualitative confirmation of the developed spot on the chromatogram was possible. In the case of an organic halogen compounds (chloro-acid, chloro-ester, iodide, and fluoride) the spot analysis was possible by the present method whereas the same spot could not give the distinct coloring with a common coloring reagents. Filterpaper thickness calibration and activity calibration induced by irradiation of the components of the filter paper, which were a source of erraneous interpretation of the spot, were searched and an average filterpaper calibration method and filter paper activity were improvised to obtain a good qualitative analysis of the spot. Finally the use and applicability of this method for the analysis identification of an organic halogen compound were evaluated. As the filter paper phase an ordinary phase (Whatmann #1, filter paper) and reversed phase (liquid paraffin impregnated) were used.

• Journal of dental hygiene science
• /
• v.15 no.5
• /
• pp.577-584
• /
• 2015

The purpose of this study was to evaluate the effect of metal chloride infiltration treatment on color and strength changes of the yttria-stabilized tetragonal zirconia polycrystals (Y-TZP). Fifty disc specimens were prepared with a Y-TZP powder (ZPEX; Tosoh, Japan). Thirty different metal chloride solutions containing 0.03~0.08 wt% chromium and 0.03~0.07 wt% terbium ions were prepared. Presintered Y-TZP specimens were soaked in metal chloride coloring liquids for 3 minutes and sintered in air at $1,450^{\circ}C$ for 2 hours. The color of the specimens was measured with spectrophotometer and color difference (${\Delta}E^*$) was obtained based on the CIE $L^*$, $a^*$, $b^*$ color coordinate values. To evaluate the effect of metal chloride infiltration strength changes, the biaxial flexural test was performed at crosshead speed 0.5 mm/min. Colors of the sintered Y-TZP showed the colors of Vita shade guide A1, A2 and A3 with the infiltration of chromium and terbium chloride solutions. Density of the sintered Y-TZP increased by the infiltration of chromium and terbium chloride solutions. Bi-axial flexural strength of the sintered Y-TZP did not show statistically significant differences by the infiltration of chromium and terbium chloride solutions (p>0.05). Chromium and terbium chloride did not affect the crystal phase of zirconia, and all specimens showed tetragonal phase. Accordingly, this study suggests that chromium and terbium chlorides can make colored zirconia while adding in a liquid form. The color of colored zirconia differ from that of vita shade guide but it can use all ceramic restoration as substructure in dental clinic.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.3
• /
• pp.765-769
• /
• 2014

An analytical methodology was developed for qualitative and quantitative impurity profiling of the coloring agent Sudan III by high-performance liquid chromatography (HPLC)-diode array detection (DAD). The impurities in commercial Sudan III were characterized by comparison of their retention times and UV spectra with those of authentic standards. Four impurities regulated by International Committees in Sudan III were quantified by HPLC-selective UV detection. The impurities in Sudan dye were successfully separated on a reversed phase C18-column within 25 min and sensitively detected by UV spectrometry at two selective wavelengths. Method validation was conducted to determine linearity, precision, accuracy, and limit of quantification (LOQ). The linear dynamic range extended from 0.002 to 4.0%, with a correlation coefficient (R2) greater than 0.995. The LOQs of the impurities ranged from 8.04 to $54.29{\mu}g/mg$. Based on the established method, the levels of regulated impurities in five commercial Sudan III dyes were determined.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.2
• /
• pp.151-157
• /
• 2010

Purpose: The purposes of this study was to evaluates shear bond strength between zirconia core and veneer-ceramic in order to examine the clinical practice of colored zirconia block fabricated by infiltration method into the metal chloride solution. Material and methods: CNU block and $Everest{(R)}$ ZS blank were used. VITA In-$Ceram{(R)}$2000 YZ Coloring liquid (LL1) and 3 aqueous metal chloride solutions containing chromium and molybdenum ingredients were used. 40 zirconia specimens were prepared into cuboid shape ($5{\times}5{\times}10 mm$). All specimens were divided into 5 groups by infiltrating into the coloring liquids. After that, porcelain was build up into the shape of $5{\times}5{\times}4mm^3$, followed by sintering. The maximum loading and shear bond strength was measured. Failure patterns and failure sites were examined. Results: 1. There were no statistical differences in shear bond strength between zirconia blocks (P > .05). 2. There were no statistically significant differences in shear bond strength between non-colored and colored zirconia blocks, while shear bond strength of non-colored zirconia blocks is higher than that of colored specimen (P > .05). 3. In the comparison with shear bond strength among colored zirconia blocks, there were no statistical differences according to kinds of coloring liquid (P > .05). 4. Mixed failure patterns were mainly observed in the failure between zirconia and veneering ceramic. The veneering ceramic failure of all specimens was observed in either interface of zirconia or veneering ceramic. Conclusion: Shear bond strength between colored zirconia and veneering ceramic shows lower tendency than non-colored zirconia, but there was clinically allowable value.

• Journal of the Korean Chemical Society
• /
• v.46 no.1
• /
• pp.57-63
• /
• 2002

The hydropurification reaction of CTA (crude terephthalic acid) was carried out with hydrogen over PdRu/CCM (carbon-carbonaceous composite material) catalyst in a batch reactor at high temperature. The first order kinetics of hydropurification is confirmed with the linear dependence of ln(4-CBA; 4-carboxybenzaldehyde) with reaction time. The reaction condition studied is thought to represent the hydropurification well because of the linear dependence of catalytic activity on the catalyst weight. The p-toluic acid (p-tol) in solid and liquid increases with the conversion of reaction or the decrease of 4-CBA. However, the benzoic acid (BA) concentration does not depend much on the conversion. The AT (alkali transmittance) does not depend on the 4-CBA when the concentration is higher than about 0.2% which shows the 4-CBA, in itself, does not cause the coloring effect. The AT of PTA depends inversely with the concentration of 4-CBA when the 4-CBA is less than about 0.15%. This may show the coloring materials are removed in parallel with the hydrogenation of 4-CBA. The (0.3%Pd-0.2%Ru)/CCM shows larger residual catalytic activity than a commercial catalyst, 0.5%Pd/C, after using in a commercial reactor even though the former has smaller fresh activity than the latter. The palladium and ruthenium in PdRu/CCM show the synergetic effect in activity when the ruthenium concentration is about $0.2{\sim}0.35$ wt%. It may be supposed that the PdRu/CCM catalyst can be a promising candidate to replace the commercial Pd/C catalyst.