• 공업화학
• /
• 제33권2호
• /
• pp.222-228
• /
• 2022

As a possible feedstock for biodiesel, the marine green alga Tetraselmis sp. was cultivated under different conditions of phototrophic, mixotrophic and heterotrophic cultures. Glycerol, a byproduct from biodiesel production process, was used as the carbon source of mixotrophic and heterotrophic culture. The effects of glycerol supply and nitrate-repletion were compared for different trophic conditions. Mixotrophic cultivation exhibited higher biomass productivity than that of phototrophic and heterotrophic cultivation. Maximum lipid productivity of 55.5 mg L^-1 d^-1 was obtained in the mixotrophic culture with 5 g L^-1 of glycerol and 8.8 mM of nitrate due to the enhancement of both biomass and lipid accumulation. The major fatty acid methyl esters (FAME) in the produced biodiesel were palmitic acid (C16:0), oleic acid (C18:1), linoleic acid (C18:2), and linolenic acid (C18:3). The degree of unsaturation was affected by different culture conditions. The biodiesel properties predicted by correlation equations based on the FAME profiles mostly complied with the specifications from the US, Europe and Korea, with the exception of the cold-filter plugging point (CFPP) criterion of Korea.

• 한국추진공학회지
• /
• 제15권4호
• /
• pp.26-34
• /
• 2011

스월러를 가진 천연가스 연료분사기가 장착된 희박 예혼합 연소기에서 화염구조의 일부분인 재순환 영역의 형성이 연소불안정에 미치는 영향에 대하여 실험적으로 연구를 진행하였다. PIV 계측기법으로 연소장에서의 화염의 안정화 그리고 불안정한 영역에서 유동장을 확인해본 결과 스월러에 의한 재순환 영역은 화염의 안정화 및 난류의 강도뿐만 아니라 재순환영역 형성의 크기에 따른 화염 재점화에도 영향을 미쳐 연소불안정 발생의 원인이 되는 열방출 섭동과 매우 밀접한 관계가 있음을 확인하였다.

• 방사성폐기물학회지
• /
• 제8권2호
• /
• pp.143-150
• /
• 2010

가압경수로 원전의 농축폐액건조설비에서 발생된 농축폐액 건조물을 유리화 하는 방안이 연구되어 왔다. 중저준위 방사성폐기물을 유리화할 경우 최종 생성물은 내구성이 우수하고 현저한 부피저감 효과의 장점을 가지고 있다. 붕산농축폐액에 대한 유리화 타당성 연구는 분말시료의 전처리 방법 개발, 유리조성 프로그램을 이용한 유리개발 및 실증시험으로 수행되었다. 분말시료에 대한 전처리 방안으로는 유리화설비에 투입하기 전에 고형성을 갖도록 펠렛화하는 것이다. 농축폐액 성분중 Na와 B의 함량 분포는 유리속에 용융되는 정도와 설비로부터의 폐기물 배출 처리에 영향을 주기 때문에 이를 고려하여 유리조성이 개발되어야 한다. 실증시험에서는 폐기물 투입률, 배기체 특성 및 최종 생성물인 유리고화체의 특성이 검토되었다. 본 연구는 붕산농축폐액에 대한 유리고화체의 물리화학적 특성을 검토하고 유리화 타당성을 확인하는데 목적이 있다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제36회 춘계학술대회논문집
• /
• pp.445-452
• /
• 2011

스월러를 가진 천연가스 연료분사기가 장착된 희박 예혼합 연소기에서 화염구조의 일부분인 재순환 영역의 형성이 연소불안정에 미치는 영향에 대하여 실험적으로 연구를 진행하였다. PIV 계측기법으로 연소장에서의 화염의 안정화 그리고 불안정한 영역에서 유동장을 확인해본 결과 스월러에 의한 재순환영역은 화염의 안정화 및 난류의 강도뿐만 아니라 재순환영혁 형성의 크기에 따른 화염 재점화에도 영향을 미쳐 연소불안정 발생의 원인이 되는 열방출 섭동과 매우 밀접한 관계가 있음을 확인하였다.

• 한국수소및신에너지학회논문집
• /
• 제28권1호
• /
• pp.56-62
• /
• 2017

Although most electricity production contributes to air pollution, the vehicle organizations and environmental agency categorizes all EVs as zero-emission vehicles because they produce no direct exhaust or emissions. Currently available EVs have a shorter range per charge than most conventional vehicles have per tank of gas. EVs manufacturers typically target a range of 160 km over on a fully charged battery. The energy efficiency and driving range of EVs varies substantially based on driving conditions and driving habits. Extreme outside temperatures tend to reduce range, because more energy must be used to heat or cool the cabin. High driving speeds reduce range because of the energy required to overcome increased drag. Compared with gradual acceleration, rapid acceleration reduces range. Additional devices significant inclines also reduces range. Based on these driving modes and climate conditions, this paper discusses the performance characteristics of EVs on energy efficiency and driving range. Test vehicles were divided by low / high-speed EVs. The difference of test vehicles are on the vehicle speed and size. Low-speed EVs is a denomination for battery EVs that are legally limited to roads with posted speed limits as high as 72 km/h depending on the particular laws, usually are built to have a top speed of 60 km/h, and have a maximum loaded weight of 1,400 kg. Each vehicle test was performed according to the driving modes and test temperature ($-25^{\circ}C{\sim}35^{\circ}C$). It has a great influence on fuel efficiency amd driving distance according to test temperature conditions.

• 한국항공우주학회지
• /
• 제43권7호
• /
• pp.619-625
• /
• 2015

스월 인젝터는 액체로켓 엔진에서의 연료 분사 장치로 널리 사용되고 있으며, 이에 따른 연구 또한 활발하게 진행되고 있다. 특히 연소 불안정 문제를 해결하는 것은 모든 종류의 액체로켓 엔진에서 필수적이다. 본 연구에서는 연소불안정을 해결하기 위한 기초 연구로 오픈형 스월 인젝터에 대한 수류실험을 수행하였다. 인젝터로 유입되는 작동유체에 압력 섭동을 발생시키고, 그에 따른 응답특성을 실험적으로 파악하였다. 또한, 인젝터 스월 챔버의 길이와 지름을 변화시킴으로써 인젝터 구조의 변화에 따른 응답 특성의 변화를 확인하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권4호
• /
• pp.508-514
• /
• 2010

본 논문은 커먼레일 디젤엔진의 정속운전시 배출되는 나노크기의 입자상 물질을 분석하는데 초점을 두었다. 디젤산화촉매 후단에서 나노입자상 물질의 개수농도 저감수준은 크지 않았으나 매연여과장치 후단에서 분석한 결과 1,000배 정도 저감되는 결과를 확인하였다. 고속 고부하 조건에서는 매연여과장치의 자연재생 효과로 인해 입자상 물질은 증가하였다. 연료분사시기를 BTDC $6^{\circ}CA$ 에서 ATDC $4^{\circ}CA$까지 지각시킨 결과 입자상 물질의 개수농도는 감소하였지만 최지각 조건인 ATDC $9^{\circ}CA$에서는 증가하는 결과를 확인하였다. EGR 적용시 핵화모드 입자상 물질은 저감되는 경향을 보였으며 축적모든 입자는 증가하였다.

• 한국자동차공학회논문집
• /
• 제19권5호
• /
• pp.58-66
• /
• 2011

A 2-loop waste heat recovery system with Rankine steam cycles for the improvement of fuel efficiency of gasoline vehicles has been investigated. A high temperature loop(HT loop) is a system to recover the waste heat from the exhaust gas, a low temperature loop(LT loop) is for heat recovery from the engine coolant cold relatively. This paper has dealt with a layout of a LT loop system, the review of the working fluids, and the design of the cycle. The design point and the target heat recovery of the LT boiler, a core part of a LT loop, has been presented and analytically investigated. Considering the characteristics of the cycle, the basic concept of the LT boiler has been determined as a shell-and tube type counterflow heat exchanger, the performance characteristics for various design parameters were investigated.

• 한국분무공학회지
• /
• 제25권1호
• /
• pp.27-33
• /
• 2020

NOx, PN and CO emissions from diesel trucks make up a significant portion of domestic air pollutant emissions. Therefore, test vehicles with various emission standards and driving modes were selected to evaluate the emission characteristics of regulated pollutants (NOx, PN, CO) in medium-duty trucks. As a result of test, all test vehicles were satisfied with Euro 5 or 6 regulation. NOx emissions of Euro 6 vehicles with after-treatment of LNT + DPF were lower than those of Euro 5 vehicles with DPF. In WLTC mode, all vehicles have high NOx emissions at section of extra high speeds, which are determined by increased fuel consumption and high combustion temperatures. CO and PN emissions from all vehicles were found to be low at section of low speeds. Also, The NO₂/NOx ratio was analyzed at 7-23% in each mode, and the NO₂/NOx ratio increased as the average vehicle speed increased. In NIER 9 mode, the CO, HC, and PN emissions were higher under cold conditions of engine than hot conditions of engine. In addition, vehicles with after-treatment system of LNT have similar NOx emissions level in this study.

• Nuclear Engineering and Technology
• /
• 제33권4호
• /
• pp.355-364
• /
• 2001

In order to evaluate and finally optimize the vitrification condition for combustible dry active waste (DAW), dust and gas generation characteristics were investigated for PE, cellulose, and mixed waste Tests were conducted by varying the operation variables such as melter configuration, excess oxygen amount, and waste feeding rate. Results showed that dust generation characteristics were affected by the operation parameters and the melter＇s configuration is the dominant one. For all tested DAWs, dust generation was reduced by increasing the waste feeding rate and the excessive oxygen amount in the melter. Among waste types, dust amount was decreased by the order of mixed wastes, PE, and cellulose. Other parameters such as temperature variation and operation time have also affected the dust generation. The optimum condition for the DAW vitrification was determined as the melter＇s configuration equipped for minimizing the waste dispersion with 20 kg/h of waste feeding rate and 100% of excessive oxygen supply. CO gas concentration in the off-gas was immediately influenced by the combustion state in the melter, but showed similar trend as the dust generation. For the NOx production during the vitrification process, thermal NOx, which is generated from the Post Combustion Chamber (PCC), rather than fuel NOx was assumed to be dominant. The gas cleaning of efficiencies of the PCC, wet scrubber, and Selective Catalytic Reduction system (SCR) were found to be high enough to keep the concentration of pollutants (CO, NOx, SOx, HCI) in the stack below their relevant emission limits.