• Journal of Sensor Science and Technology
• /
• v.6 no.6
• /
• pp.466-475
• /
• 1997

In this paper, an implantable middle ear hearing aids using an electromagnetic transducer which consists of a tiny coil and a magnet is designed, and objective design method to implement a vibrator of the electromagnetic type transducer is proposed. Sound characteristic of the electromagnetic type vibrator is excellent but power transfer rate is lower than that of a ceramic type. To improve power transfer efficiency of system, external and inner part of a middle ear system is designed using FM transmission method. We implemented an experimental set of the designed transducer, inner part, and outer part. Then, we measured vibration characteristics of a metal strip and a temporal bone of a dead body. As the results, we confirmed the advantage of FM method and showed that designed transducer could effectively transmit vibration of amplified input sound pressure to ossicle.

• Journal of Sensor Science and Technology
• /
• v.4 no.3
• /
• pp.9-14
• /
• 1995

For the development of liquid density measuring sensor using the natural frequency of a pipe, its principle and construction method were described. The stainless steel pipe, which has length of 32 cm, inside diameter of 2.3 cm and outside diameter of 2.5 cm, was used for the sensor. The exciting coil and the photo sensor were used to excite and to pick-up it, and the feedback circuit was designed to continue its vibrating. The natural frequency was consistent with the result of the spectrum analysis. It had a linearity of 0.0027 % and a sensitivity of 0.032 % in liquid density range from $0.8\;g/cm^{3}$ to $1.4\;g/cm^{3}$ and its frequency variation ratio was 0.024 $%/^{\circ}C$ in temperature range from $10^{\circ}C$ to $35^{\circ}C$.

• Journal of the Institute of Convergence Signal Processing
• /
• v.15 no.4
• /
• pp.148-154
• /
• 2014

This paper suggests a new system based on image-processed information which is designed to control traffic light by measuring two-way traffic at the same time with a surveillance camera. With this system, the existing way of using one camera for one lane or loop coil will be improved to the more effective way of using only one camera to monitor a two-way, 8 lane roads statistically. Car images can be detected clearly even in irregular condition because of the background updating in real time. In addition, more accurate measurement is possible to users by selecting extra attention-needed regions. The automatic traffic light controlling algorithm, suggested in this paper, will prevent users and drivers from wasting their time and energy by controlling the number of traffic in advance.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.3
• /
• pp.9-12
• /
• 2012

Usually, the AC loss from the superconducting element of an SFCL due to the load current is very small because it is composed of the combination of bifilar windings with very small reactance. Although the AC loss is small enough, we should be albe to predict for the design and control of the cryogenic system. In fact, an SFCL for the transmission voltage class may not generate ignorable AC loss because of the inevitable space between the HTS wires for the high voltage insulation and cryogenic efficiency. To measure the AC loss dependency on the space between the 2G HTS wires with the width of 4.4 mm, we prepared an experimental setup which could adjust the distance between the wires. We used two 500-mm length HTS wires in parallel and applied the current in the opposite direction for each wire to simulate a part of a current limiting module for a high voltage SFCL. We also put two couples of voltage taps at the ends of each wire and a cancel coil in the voltage measurement circuit to compensate the reactive component from the voltage taps. In this condition, we varied the distance between the wires to investigate the change of the transport current loss. A similar experimental study with HTS wire with the width of 12 mm is now in progress.

• Progress in Superconductivity and Cryogenics
• /
• v.17 no.1
• /
• pp.48-52
• /
• 2015

The electrical insulation design for a superconducting coil system is important for developing high voltage superconducting apparatuses. Also, the degraded characteristics of superconducting tapes due to an electrical breakdown should be considered for superconducting coils design. In this study, the degradation characteristics of 2G high temperature superconducting (HTS) tapes were studied with respect to electrical breakdown tests. The degradation tests of 2G HTS tapes were performed with various stabilizer materials. The degradation characteristics of 2G HTS tapes such as critical current(Ic) and index number were observed by performing electrical breakdown tests. It was found that the characteristics such as Ic and index number can be degraded by an electrical breakdown. Moreover, it was concluded that the degradation characteristics of 2G HTS tapes were affected by a stabilizer material and applied breakdown voltage. The cross sectional view of 2G HTS tapes was observed by using a scanning electron microscope (SEM). As results, it is found that the degradation characteristics of 2G HTS tapes are concerned with hardness and electrical resistivity of stabilizer layers.

• KSBB Journal
• /
• v.17 no.4
• /
• pp.350-356
• /
• 2002

Low density polyethylene(LDPE) film was fabricated with the addition of benzoic acid, or/and JP which contained water-soluble silica adsorbed a natural antimicrobial compounds. The used antimicrobial compounds were isolated from culture broths of methylotropic actinomycetes strains MO-16 and MO-17 which was newly isolated from soils. An antimicrobial compound retained antimicrobial activity after heat treatment at 121$^{\circ}C$ for 5 min. JP, which obtained from Japan as a antimicrobial agent, showed antimicrobial activity in the concentration of 100 mg/mL. The silica LDPE film revealed the growth inhibition of total aerobic bacteria in packaged minced pork compared with commercial film and of E. coil on a contained agar plate. In the storage testing of various packaged foods at room temperature for 30 days, the film showed excellent preservation compared with commercial film in case of small tomato and Agaricus bisporus.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.11
• /
• pp.601-611
• /
• 2002

As resent trends in structural construction have been to build taller and larger structures than any time in the past, they have had high flexibility and low damping that can cause large vibration response under severe environmental loading such as earthquakes, winds, and mechanical excitations. The damper with mass and sqring is one aproach to safeguarding the structure against excessive vibrations. In this paper, a large capacity hybrid-type linear motor damper(LMD) was designed and fabricated for the application to the vibration control of a large building structure model. It has been designed to be able to move the damper mass, 1,500 kg up to ${\pm}250mm$ strokes at the first mode natural frequency of the building structure model, ${\pm}0.51Hz$. Linear motor is consisted of the fixed coil and the movable NdFeB permanent magnets field part. The PM field part composed magnet modules and iron yoke, is the damper mass itself, 1500kg. LMD therefore has a simplified structure and requires a few elements in the driving system, being compared with a rotary motor damper and a hydraulic damper. However, the manufacture of large PM linear actuator is difficult because of the limit of PM size and the attraction and repulsion at the assembly of PM. Therefore, large damper system is manufactured and tested for dynamic characteristics and frequency response.

• Journal of the Korean Magnetics Society
• /
• v.6 no.6
• /
• pp.367-374
• /
• 1996

The developmement of electronic machine industries requires miniature of size as well as increasement of driving frequency in electronic parts, recently. To realize micro-struture of magnetic devices, in this study, we fabricated thin film inductors by using thin film manufacturing techniques such as photolithography and wet etching process, and these devices are measured at high frequency range of 1 MHz~1 GHz. The results are as follows. The accurate measuring technique by using network analyzer system having microstrip line was established. The manufactured inductors are fabricated with several ten micrometers by means of wet etching process known as easier and more economic than dry etching process. VVhen the device size of two types (spiral, meander) is the same, inductance value L and quality factor Q of spiral type devices are larger than those of meander type, but driving frequency of spiral type is lower than that of meander type due to increasement of inductance L. It is necessary to decrease resistance value R by increasing cross section of the conductor film coil. Thus high frequency measuring method would be a very useful for another measuring fields of the range over several hundreds MHz.

• 한국균학회소식:학술대회논문집
• /
• 2015.11a
• /
• pp.26-26
• /
• 2015

Phytophthora infestans is the causal agent of potato and tomato late blight, one of the most devastating plant diseases. P. infestans secretes effector proteins that are both modulators and targets of host plant immunity. Among these are the so-called RXLR effectors that function inside plant cells and are characterized by a conserved motif following the N-terminal signal peptide. In contrast, the effector activity is encoded by the C terminal region that follows the RXLR domain. Recently, I performed in planta functional profiling of different RXLR effector alleles. These genes were amplified from a variety of P. infestans isolates and cloned into a Potato virus X (PVX) vector for transient in planta expression. I assayed for R-gene specific induction of hypersensitive cell death. The findings included the discovery of new effector with avirulence activity towards the Solanum bulbocastanum Rpi-blb2 resistance gene. The Rpi-blb2 encodes a protein with a putative CC-NBS-LRR (a coiled-coil-nucleotide binding site and leucine-rich repeat) motif that confers Phytophthora late blight disease resistance. We examined the components required for Rpi-blb2-mediated resistance to P. infestans in Nicotiana benthamiana. Virus-induced gene silencing was used to repress candidate genes in N. benthamiana and to assay against P. infestans infections. NbSGT1 was required for disease resistance to P. infestans and hypersensitive responses (HRs) triggered by co-expression of AVRblb2 and Rpi-blb2 in N. benthamiana. RAR1 and HSP90 did not affect disease resistance or HRs in Rpi-blb2-transgenic plants. To elucidate the role of salicylic acid (SA) in Rpi-blb2-mediated resistance, we analyzed the response of NahG-transgenic plants following P. infestans infection. The increased susceptibility of Rpi-blb2-transgenic plants in the NahG background correlated with reduced SA and SA glucoside levels. Furthermore, Rpi-blb2-mediated HR cell death was associated with $H_2O_2$, but not SA, accumulation. SA affects basal defense and Rpi-blb2-mediated resistance against P. infestans. These findings provide evidence about the roles of SGT1 and SA signaling in Rpi-blb2-mediated resistance against P. infestans.

• Nuclear Engineering and Technology
• /
• v.48 no.5
• /
• pp.1206-1218
• /
• 2016

This article proposes a highly reliable power and communication system that guarantees the protection of essential instruments in a nuclear power plant under a severe accident. Both power and communication lines are established with not only conventional wired channels, but also the proposed wireless channels for emergency reserve. An inductive power transfer system is selected due to its robust power transfer characteristics under high temperature, high pressure, and highly humid environments with a large amount of scattered debris after a severe accident. A thermal insulation box and a glass-fiber reinforced plastic box are proposed to protect the essential instruments, including vulnerable electronic circuits, from extremely high temperatures of up to $627^{\circ}C$ and pressure of up to 5 bar. The proposed wireless power and communication system is experimentally verified by an inductive power transfer system prototype having a dipole coil structure and prototype Zigbee modules over a 7-m distance, where both the thermal insulation box and the glass-fiber reinforced plastic box are fabricated and tested using a high-temperature chamber. Moreover, an experiment on the effects of a high radiation environment on various electronic devices is conducted based on the radiation test having a maximum accumulated dose of 27 Mrad.