• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.8
• /
• pp.675-680
• /
• 2000

In this study the temperature coefficient of resonant frequency(TC $F_{r}$) dielectric and piezoelectric properties of Pb[(S $b_{1}$2//N $b_{1}$2/)$_{0.065}$)-(Z $r_{x}$, $Ti_{1-x}$ )$_{0.90}$] $O_3$ceramics were investigated with Zr/Ti ratio. The compositions near the morphotropic phase boundary (MPB) appeared when Zr/Ti ratio was 49.5/50.5 The dielectric constant and electromechanical coupling factor( $k_{p}$) also showed the highest values of 1,257, 0.653 respectively when the Zr/Ti ratio was 49.5/50.5 Moreover the mechanical quality factor( $Q_{m}$) showed th lowest value of 713 when the Zr/Ti ratio. The temperature coefficient of resonant frequency(TC $F_{r}$) abruptly change at the morphotropic phase boundary(MPB) which existed between the rhombohedral phase with highly negative TC $F_{r}$ of -106ppm/$^{\circ}C$ and the tetragonal phase with highly positive TC $F_{r}$ of +64pp $m^{\circ}C$ as Zr/Ti ratio varied from 50/50 to 49.5/50.5.50.5..50.5.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.2
• /
• pp.135-139
• /
• 2008

In this paper, tunable SC(switched capacitor) 2nd order bandpass $\Sigma-\Delta$(Sigma-Delta) modulator with novel architecture that can adjust the IF band center frequency by one coefficient value is proposed for data conversion in the IF(Intermediate Frequency) band. Its architecture can optionally adjust all the 2nd order noise transfer function in comparison with the conventional architecture. In order to adjust the center frequency, the conventional architecture needs the two variable coefficient values, basic clock and eight clocks. On the other hand, the proposed architecture can adjust the center frequency by one variable coefficient value and basic clock only.

• Tribology and Lubricants
• /
• v.13 no.3
• /
• pp.33-41
• /
• 1997

In this paper the linearized stiffness and damping coefficients of tilting pad thrust bearing are calculated by the perturbation method. The coefficients are obtained for a wide range of pivot positions. The effects of exciting frequency and pad mass on stiffness and damping coefficients are investigated. Critical frequencies due to the tilting motions of the pad are presented and are shown to be strongly influenced by the pivot position and the pad mass.

• International Journal of Aeronautical and Space Sciences
• /
• v.18 no.4
• /
• pp.797-806
• /
• 2017

In this study, the reflection coefficient (RC) and the flame transfer function (FTF) were measured by applying acoustic excitation to a duct-type model combustor and were used to predict the frequency of the combustion instability (CI). The RC is a value that varies with the excitation frequency and the geometry of the combustor as well as other factors. Therefore, in this study, an experimentally measured RC was used to improve the accuracy of prediction in the cases of 25% and 75% hydrogen in a mixture of hydrogen and methane as a fuel. When the measured RCs were used, an unstable condition was correctly predicted, which had not been predicted when the RCs had been assumed to be a certain value. The reason why the CI occurred at a specific frequency was also examined by comparing the peak of the FTF with the resonance frequency, which was calculated using Helmholtz's resonator analysis and a resonance frequency equation. As the CI occurred owing to the interaction between the perturbation in the rate of heat release and that in the pressure, the CI was frequent when the peak of the FTF was close to the resonance frequency such that constructive interference could occur.

• Journal of Sensor Science and Technology
• /
• v.24 no.3
• /
• pp.181-187
• /
• 2015

The magnetoelectric characteristics on layered $Fe_{78}B_{13}Si_9/PZT$ and $Fe_{78}B_{13}Si_9/PZT/Fe_{78}B_{13}Si_9$($t_m=0.017$, 0.034mm) composites by epoxy bonding for magnetic field sensor were investigated in the low-frequency range and resonance frequency range. The optimal bias magnetic field $H_{dc}$ of these samples was about 23~63 Oe range. The Me coefficient of $Fe_{78}B_{13}Si_9/PZT/Fe_{78}B_{13}Si_9(t_m=0.034mm)$ composites reaches a maximum of $186mV/cm{\cdot}Oe$ at $H_{dc}=63Oe$, f=50 Hz and a maximum of $1280mV/cm{\cdot}Oe$ at $H_{dc}=63Oe$, resonance frequency $f_r=95.5KHz$. The output voltage shows linearity proportional to ac fields $H_{ac}$ and is about U=0~130.6 mV at $H_{ac}=0{\sim}7Oe$, f=50 Hz, U=0~12.4 V at $H_{ac}=0{\sim}10Oe$, $f_r=95.5KHz$(resonance frequency). The optimal frequency(f=50 Hz) of this sample is around the utility ac frequency(f=60 Hz). Therefore, this sample will allow for ac magnetic field sensor at utility frequency and low bias magnetic fields $H_{dc}$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.9
• /
• pp.726-730
• /
• 2001

Temperature stabilities of dielectric constraints and resonant frequencies of the substrates are very important in piezoelectric ceramics oscillators and filters. In this study, it was investigated temperature stability of the length-extensional vibration mode of Pb(Zr$\_$y/Ti$\_$1-y/)O$_3$+x[wt%]Cr$_2$O$_3$ ceramics. The mode can be utilized in fabricating ultra-small 455 kHz IF devices. Addition of Cr$_2$O$_3$ in morphotrophic phase PZT decreased the variations of dielectric constant, electro-mechanical coupling factor k$\_$31/ and resonant frequency by thermal shock. As additive weight of Cr$_2$O$_3$increased, the temperature coefficient of resonant frequency changed from positive number to negative one. And the composition tith temperature coefficient of resonant frequency was shifted to the one with increased Cr$_2$O$_3$ additive weigh by thermal aging.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.521-524
• /
• 2005

To protect a satellite and electronic equipment from the acoustic loads generated by rocket propulsion system, many launch vehicle use acoustic blanket. Most high frequency region of the acoustic loads is reduced by nose fairing skins and acoustic barrier, but low frequency region is not. In order to control low frequency acoustic mode, we designed away resonator panel which was made of composite materials. This paper shows the absorption coefficient measurement result of resonator and SPL(Sound Pressure Level) reduction by using resonators in a rectangular cavity for experiment. Proper arrangement of acoustic resonators at each mode reduce effectively SPL around the satellite through changing boundary condition.

• International Journal of Ocean Engineering and Technology Speciallssue:Selected Papers
• /
• v.3 no.1
• /
• pp.23-28
• /
• 2000

A numerical investigation was made to examine characteristics of rectangular pontoon type floating breakwaters in oblique waves. Sway and heave wave exciting forces, roll moment acting on the floating breakwater and three motion reponses decrease as the incident wave angle increases for the most of the wave ranges. There exists a minimum wave transmission coefficient which is a function of wave frequency. In short wave range wave transmission coefficient increases as the incident wave angle increases. In long wave range, however, wave transmission coefficient decreases as the wave incident angle increases.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.21-24
• /
• 2008

This study proposes a optimized shape of diffuser profile through investigating the scattering and diffusion characteristics of diffusers. The scattering coefficient according to ISO 17497-1 evaluates uniformity of reverberant sound field of late reflections, while the diffusion coefficient according to AES-4id-2001 evaluates polar response of early reflections. Thus both scattering and diffusion characteristics should contribute to design shape of diffusers to maximize physical performance. To find out design method, the previous results on hemisphere diffusers are reviewed. The frequency characteristics of scattering coefficients depended on the structural height of the diffusers, while amount of scattering coefficients depended on the surface coverage density of the diffusers. However absorptive properties also increased with augment of surface coverage density, thus optimum coverage density should be considered. For the directional diffuser, three types of 2D-diffusers are proposed; semicylinder of h=5mm, semi-truncated cone of h=5-25mm and semicylinder of h=25mm. As results, diffusers with the maximum height of 25mm show the highest scattering coefficients, while diffuser of h=5mm shows high scattering coefficients only at the high-frequency bands. Diffusion coefficient will be investigated for diffusive properties of the early reflection.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.12
• /
• pp.1011-1016
• /
• 2000

The (1-x)MgTi $O_3$-xSrTi $O_3$(x=0.02~0.08) ceramics were fabricated by the conventional mixed oxide method. The sintering temperature and time were 125$0^{\circ}C$~1375$^{\circ}C$ and 2hours. The structure and microwave dielectric properties were investigated with sintering temperature and composition ratio. From the X-ray diffraction patterns, the cubic SrTi $O_3$and hexagonal MgTi $O_3$structures were coexisted in the (1-x)MgTi $O_3$-xSrTi $O_3$(x=0.02~0.08) ceramics. The dielectric constant($\varepsilon$$_{r}$) was increased and the temperature coefficient of resonant frequency($\tau$$_{f}$)was decreased with addition of SrTi $O_3$. The temperature coefficient of resonant frequency($\tau$$_{f}$) was gradually varied from negative value to positive value with increasing SrTi $O_3$. In the case of 0.96MgTi $O_3$-0.04SrTi $O_3$ceramics sintered at 130$0^{\circ}C$, the dielectric constant, quality factor and temperature coefficient of resonant frequency were 20.5, 5918(at 7.33GHz) and +10ppm/$^{\circ}C$, respectively.y.y.y.