• 대한금속재료학회지
• /
• 제49권5호
• /
• pp.367-373
• /
• 2011

This paper studies the experimental method that uses the homogeneous precipitation method to prepare mica flakes coated with anatase-type titania pearlescent pigment with urea as precipitant. The optimum technology parameters, the chemical composition, the microstructure, and the color property of resulting pigments are discussed. The coating principle of mica coated titania with various coating thickness is analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy(TEM) and tested by spectrophotometer analysis. The colored nanocrystalline pigments with different morphology and coating thickness 45-170 nm were prepared by homogeneous precipitation treatment of $TiOSO_4$(titanum oxysulfate) aqueous solutions. Characterizations on the pigments show that the pearlescent effects of the pigments depend mainly on mica size, thickness of the metal oxide deposit, its chemical composition, and crystal structure.

• 대한치과보철학회지
• /
• 제45권6호
• /
• pp.769-779
• /
• 2007

Statement of problem. When TiN coating is applied to the abutment screw, occurrence of greater preload and prevention of the screw loosening could be expected due to decrease of frictional resistance. However, the proper thickness of TiN coating on abutment screw has not been yet reported. Purpose. The purpose of this study is to find out the appropriate TiN coating thickness by evaluating the detorque force and the surface change of titanium abutment screw with various TiN coating thickness. Material and methods. 1. Material Thirty five non-coated abutment screws were prepared for TiN coating. TiN coatings were prepared by Arc ion plating method. Depending on the coating deposition time(CDT), experimental groups were divided into 6 groups(CDT 30min, 60min, 90min, 120min, 150min, 180min) and those of 1 group was not coated as a control group. Each group was made up of 5 abutment screws. 2. Methods FE-SEM(Field Emission Scanning Electron Microscoper) and EDX(Energy Dispersive X-ray Spectroscopy) were used to observe the surface of the abutment screw. Electric scales was used to measure the weight of the abutment screw after the repeated closing and opening of 10 trials. Detorque force was measured with digital torque gauge, at each trial. Results. 1. As the coating deposition time increased, the surface became more consistent and smooth. 2. As for the abutment screws that were TiN coated for more than 60 minutes, no surface change was found after the repeated closing and opening. 3. The TiN coated abutment screws showed less weight change than the non-coated abutment screws. 4. The TiN coated abutment screws showed higher mean detorque force than the noncoated abutment screws. 5. The abutment screw coated for 60 minutes showed the highest mean detorque force. Conclusion. The coating layer of proper thickness is demanded to obtain consistent and smooth coating surface, resistance to wear, and increased detorque force of the abutment screw. In conclusion, the coating deposition time of 60 minutes indicated improved mechanical property, when TiN coating was conducted on titanium abutment screw.

• 폴리머
• /
• 제35권6호
• /
• pp.574-579
• /
• 2011

자동차 선도장 강판을 위한 핵심 응용기술로서 3-롤코팅 공정을 연구하였다. 본 연구를 위한 3-롤코팅은 저장조로부터 코팅액을 끌어 올리는 pick-up롤, 적절한 코팅 두께로 계량시키기 위한 계량롤, 강판에 직접 코팅시키기 위한 applicator 롤로 구성되어 있다. 전단담화의 유변물성을 갖는 고분자 도료의 코팅 유동 특성과 코팅 운전 영역을 pickup 롤과 계량롤 사이의 속도비와 간격 등의 공정조건과의 상관관계를 통해 고찰하였다. 안정한 코팅 영역에서, 간격이 크거나 속도비가 작을수록 코팅 두께는 증가하였다. 또한, ribbing과 cascade라는 불안정성은 각각 속도비가 낮고 높을 때 관찰되었다. 특히, 속도비가 낮을때, ribbing의 파장과 심각도가 증가함을 확인하였다.

• Steel and Composite Structures
• /
• 제15권1호
• /
• pp.1-14
• /
• 2013

Predicting the fire resistance of structures has been significantly advanced by full scale fire tests in conjunction with improved understanding of compartmental fire. Despite the progress, application of insulation is still required to parts of structural steelwork to achieve over 60 minutes of fire rating. It is now recognised that uncertainties on insulation properties hinder adaptation of performance based designs for different types of structures. Intumescent coating has recently appeared to be one of most popular insulation types for steel structures, but its design method remains to be confirmed by empirical data, as technical difficulties on the determination of the material properties at elevated temperatures exist. These need to take into account of further physiochemical transitions such as moving boundary and endothermic reaction. The impetus for this research is to investigate the applicability of the conventional differential equation solution which examines the temperature rise on coated steel members by an inorganic intumescent coating, provided that the temperature-dependent thermal/mechanical insulation properties are experimentally defined in lab scale tests.

• 한국표면공학회지
• /
• 제36권5호
• /
• pp.398-405
• /
• 2003

The stainless steel wire requires good corrosion resistance and mechanical properties, such as drawing ability, combined with a high resistance to corrosion. For increasing drawing ability of stainless steel, Ni coating methods have been used in this study. However, there is no information on the electrochemical corrosion behavior of drawed wires after Ni coating. To investigate corrosion resistance and mechanical property of drawed wire, the characteristics of Ni coated wires have been determined by tensile strength tester, hardness tester, field emission scanning microscope, energy dispersive x-ray analysis and potentiodynamic method in 0.1 M HCl. The drawed stainless steel wires showed the strain-induced martensitic structure, whereas non-drawed stainless steel wire showed annealing twin in the matrix of austenitic structure. The hardness and tensile strength of drawed stainless steel wire were higer than that of non-drawed stainless steel wire. Electrochemical measurements showed that, in the case of drawed stainless steel o ire after Ni coating, the corrosion resistance and pitting potential increased compared with non-coated and drawed stainless steel wire due to decrease in the surface roughness.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 2003년도 가을 학술발표회 논문집
• /
• pp.38-41
• /
• 2003

Recently, Waterhorne polyurethane(WBPU) have been used for a wide range of commercial applications due to the increasing environmental regulation to reduce low-volatile organic compounds in coating and adhesives materials [1-8]. The WBPU was used in coating industry on fiber at first, and its market is increasing these days. Especially, the Waterborne polyurethane film even is widely used in the field of breathable coating fiber or medical science [9-10]. Water vapor permeability(WVP) is the key property for application to breathable coating fiber. (omitted)

• 한국가구학회지
• /
• 제11권1호
• /
• pp.37-44
• /
• 2000

This work was done to investigate problems of cashew coating in a wooden-art industry such as ritual vessels and to improve a curing property of cashew film. The main problem in the cashew coating industry was a small-scale business, insufficiency of facilities, lack of knowledge about cashew resin and painting, and lack of a technology of productivity improvement by accelerated drying time of cashew film. In present, cashew coating for ritual vessels mostly used the petroleum as a thinner. The time of set to touch of cashew film thinning with petroleum on glass plates was increased with the increasement of the thinning proportion, but retarded from 3 to 11 times compared to that of an exclusive thinner according to thinning level. The addition of 20% aceton to petroleum contributed to the high reduction rate up to about 60% at the thinning level of 100%, which was effective to accelerate the drying time of cashew film. Even though only the petroleum or the petroleum-aceton(20%) mixture was used as a thinner, it did not exhibit any distinguishable differences in crack and appearance of cashew-film coated on Frexinus rhynchophylla after 5 cycles of soak under the vacuum-drying treatment.

• Corrosion Science and Technology
• /
• 제4권1호
• /
• pp.33-38
• /
• 2005

Some feasibility studies are conducted to produce an advanced ceramic coating, which reveals superior chemical and mechanical strength, on metal base structure used in chemical plant. This advanced coating on metallic frame can replace ceramic delivery pipe and reaction chamber used in chemical plant, which are operated in hi-temperature and corrosive/erosive environment. An dual spraying is adopted to reduce the residual stress in order to increase the coating thickness and the residual stress is estimated by in-situ manner. Then new methodology is tried to form special coating of yttrium aluminum garnet(YAG), which reveals hi-strength and low-creep rates at hi-temperature, superior anti-corrosion property, hi-stability against Alkali-Vapor corrosion, and so on, on iron base structure. To verify the formation of YAG during thermal spraying, XRD(X ray diffraction) technique was used.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.215-222
• /
• 2007

Coating of Hot-dip galvannealed steel consists of various Fe-Zn intermetallic compounds. Since the coating is hard and there for is very brittle, the surface of steel sheet is easy to be ruptured during second manufacturing processing. This is called as powdering. In addition, forming equipment might be polluted with debris by powdering. Therefore, various research have been carried out to prohibit powdering fur improving the quality of GA steel. This paper carried out finite element analysis combined with damage model which simulate the failure of local layer of hot-dip galvannealed steel surface during v-bending test. Since the mechanical property of intermetallic compound was unknown exactly, we used the properties calculated from measurements. The specimen was divided into substrate, coating layer and interface layer. Local failure at coating layer or interface layer was simulated when elemental strain reached a prescribed strain.

• Journal of Welding and Joining
• /
• 제18권6호
• /
• pp.96-101
• /
• 2000

Sintered alumina ceramic substrate has been used for the insulating substrate for thick Hybrid IC owing to its cheapness and good insulating properties. Some of thick HIC's are important to eliminate the heat emitted from the parts that are mounted on the ceramic substrate. Sintered ceramic substrate can not transfer and emit the heat efficiently. It's been tried to do plasma spray coating of alumina ceramic on the metal substrates that have a good heat emission property. The most important properties to commercialize this ceramic coated metal substrate are surface roughness and deposition efficiency. In this study, plasma spray coating parameters are optimized to minimize the surface roughness and to maximize the deposition efficiency using Taguchi experimental method. By this optimization, the deposition efficiency was greatly improved from 35% at the frist time to 75% finally.