• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.47-47
• /
• 2008

P-type transparent semiconductor $SrCu_2O_2$ thin films have been prepared by RF sputtering using low-alkali glass for LCD and quartz as substrates. Single phase of $SrCu_2O_2$ powder was obtained by heating a stoichiometric mixture of CuO and $SrCO_3$ at 1223K for 96h under N2 gas flow, and target was fabricated at 1243K for 24h. Room temperature conductivity of the sintered body was about 0.02S/cm, and the activation energy in the temperature range of $-50^{\circ}C$~RT and RT~$150^{\circ}C$ were 0.18eV, 0.07eV, respectively. Effects of deposition pressure and post-annealing temperature on the electrical and optical properties of the obtained thin film have been investigated.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.4
• /
• pp.173-178
• /
• 2009

DLC film was synthesized on plastic injection mold(SKD11, $30\;mm\;{\times}\;19\;mm\;{\times}\;0.5\;mm$) and Si(100) wafer for 2 h at $130^{\circ}C$ under 6 mTorr using hybrid method of rf sputtering and ion source. The obtained film was analysed by Raman spectroscopy, AFM, TEM, Nano indenter and scratch tester, etc. The film was defined as an amorphous phase. In the Raman spectrum, broad peak of $sp^2$-bonded carbon attributed to graphite at $1550\;cm^{-1}$ were observed, and the ratio of ID($sp^3$ diamond intensity)/IG($sp^2$ graphite intensity) was approximately 0.54. The adhesion of DLC film was more than 80 N with scratch tester when $0.2\;{\mu}m$ thickness Cr was coated as interlayer. The micro-hardness was distributed at 35~37 GPa. The friction coefficient was 0.02~0.07, and surface roughness(Ra) was 0.34~1.64 nm. The lifetime of DLC coated plastic injection mold using as a connector part in computer was more than 2 times of non-coated mold.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.1
• /
• pp.29-32
• /
• 2010

In this study, transparent and conductive Al-doped zinc oxide (AZO) films were prepared on a glass substrate by an radio frequency (RF) magnetron sputtering method using a 150-nm-thick AZO target (Al: 2 wt.%) at room temperature. We investigated the effects of RF power between 100-350 W (in steps of 50 W) on the structural, electrical, and optical properties of the AZO films. The thickness and cross-sectional images of the films were observed by field emission scanning electron microscopy. The thicknesses of all films were kept constant at 150 nm and grown on a glass substrate. The grain sizes of the AZO films were determined with the X-ray diffraction by using the Scherrer' equation, and their electrical properties were investigated using a Hall effect electronic transport measurement system. The transmittance of the AZO films was also measured by an ultraviolet-visible spectrometer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.359-359
• /
• 2010

Self-organized nanostructures of dots, holes or ripples produced by energetic ion bombardment have been reported in a wide variety of substrates. Ion bombardment on an alloy or compound also draws much attention because it can induce a surface composition modulation with a topographical surface structure evolution. V. B. Shenoy et al. further suggested that, in the case of alloy surfaces, the differences in the sputtering yields and surface diffusivities of the alloy components will lead to a lateral surface composition modulation [1]. In the present work, the classical molecular dynamics simulation of Ar bombardment on metallic alloys at room temperature revealed that this bombardment induces a surface composition modulation in layer-by-layer mode. In both the $Co_{0.5}Cu_{0.5}$ alloy and the CoAl B2 phase, the element of higher-sputtering yield is accumulated on the top surface layer, whereas it is depleted in lower layers. A kinetic model considering both the rearrangement and the sputtering of the substrate atoms agrees with the puzzling simulation results, which revealed that the rearrangement of the substrate atoms plays a significant role in the observed composition modulation.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.3
• /
• pp.117-122
• /
• 2012

ZTO/GZO double layered films were prepared on unheated non-alkali glass substrates. ZTO films were deposited by RF/DC hybrid magnetron co-sputtering using ZnO (RF) target and $SnO_2$ (DC) targets, and then GZO films were deposited by DC magnetron sputtering using an GZO ($Ga_2O_3$:5.57 wt%) target. These films were post-annealed at temperature of 200, $300^{\circ}C$ in air and vacuum ambient for 30 min. In the case of post-annealing in air, ZTO/GZO double layer showed relatively low resistivity change, compared to GZO single layer. Furthermore, ZTO/GZO double layer revealed low WVTR, compared to GZO single layer. Therefore, it can be confirmed that ZTO film doing a role with barrier for water or oxygen diffusion.

• Journal of Energy Engineering
• /
• v.26 no.3
• /
• pp.30-50
• /
• 2017

Currently, exhaust gas emitted from thermal power plants and various combustion facilities that consume large amounts of fossil fuels such as coal, oil, and natural gas contains high concentrations of $CO_2$ and is a major cause of global warming. Conventionally, as a countermeasure against this problem, research and development are being carried out from various fields, and it is considered to be one of the most promising methods for separating and recovering $CO_2$ in the exhaust gas. One of the reasons for the low use of carbon dioxide is oxidized among the carbon compounds and is present in the most stable state. From the viewpoint of $CO_2$ emissions, $CO_2$ immobilization technology, which converts $CO_2$ into chemically useful compounds, is considered to be more important.

• Journal of the Korean Magnetics Society
• /
• v.9 no.6
• /
• pp.296-300
• /
• 1999

Cross-shape structures of spin tunneling junctions were fabricated using DC magnetron sputtering and metal masks. The film structures were $substrate/Ta/NiFe/FeMn/NiFe/CoFe/Al_2O_3/CoFe/NiFe$ and $substrate/Ta/NiFe/CoFe/ Al_2O_3/CoFe/NiFe/FeMn/NiFe$. Fabrication conditions of insulating layer ($Al_2O_3$) and thickness and sputtering power of each film layer were varied, and maximum magnetoresistance ratio of 24.3 % was obtained. Magnetic characteristic variations in the above mentioned two structures and two types of substrates (Corning glass 7059 and Si(111)) were compared. Annealing of the junctions was performed to find out magnetic characteristic variations expected from the device fabrication. Magneoresistance Ratio were observed to maintain as-deposited value up to 150 $^{\circ}C$ annealing and then to drop rapidly after 180 $^{\circ}C$ annealing.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.12a
• /
• pp.334-334
• /
• 2003

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.91-91
• /
• 2003

• Proceedings of the Korean Vacuum Society Conference
• /
• 2005.02a
• /
• pp.76-76
• /
• 2005