• Membrane and Water Treatment
• /
• v.10 no.2
• /
• pp.127-137
• /
• 2019

The D2EHPA/TBP co-extractants immobilized PolyHIPE membrane can be used for the selective separation of Mn (II) from Co (II). By solvent-nonsolvent method, D2EHPA/TBP co-extractants can be effectively immobilized into PolyHIPE membrane. The pore structure of PolyHIPE membrane and the presence of TBP enhance the stability of immobilized co-extractants. The optimal operating conditions for the separation of Mn (II) and Co (II) are feeding phase at pH 5.5, sulfuric acid concentration in the stripping phase of about 50 g/L and stirring speed at 400 rpm. The D2EHPA/TBP co-extractants ratio of 5:1 shows synergetic effect on Mn/Co separation factor about 22.74. The removal rate and recovery rate of Mn (II) is about 98.4 and 97.1%, respectively, while for Co (II) the transport efficiency is insignificant. The kinetic study of Mn (II) transport shows that high initial flux, $J_f^o=80.1({\mu}mol/m^2s)$, and maxima stripping flux, $J_s^{max}=20.8({\mu}mol/m^2s)$, can be achieved with D2EHPA/TBP co-extractants immobilized PolyHIPE membrane. The stability and reusability study shows that the membrane can maintain a long term performance with high efficiency. High purity of Co (II) and Mn (II) can be recovered from the feeding phase and stripping phase, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3761-3767
• /
• 2009

This study was investigated to determine the combustion characteristics, decomposition efficiency, and the flue gas concentrations after combustion in the high temperature reactor($1,250{\sim}1,400^{\circ}C$, 1 atm) for the liquid wastes(waste oil and waste solvent) generated from the industrial complex. The concentration of nitrogen oxide(NOx) is decreased and the synthetic gas is increased when the mass ratio of $O_2$/waste is about 1.53 because the reaction condition was changed to reduction state. And BTEXs(benzene, toluene, ethylbenzene, xylene) are decomposed more than 99.99%. If the highly concentrated liquid waste (waste oil and waste solvent) is treated under the operating conditions suggested by this study, our treatment method for the liquid waste was found to be proper because of the contaminants emission concentration is very low. In addition, the synthetic gas after combustion can be used as an alternative fuel.

• Journal of Applied Biological Chemistry
• /
• v.59 no.1
• /
• pp.5-7
• /
• 2016

One of oriental medicinal plants, Potentilla chinensis, has been used for anti-inflammation, hemostatic, decryption, and antipyretic. Especially, a root of Potentilla chinensis was used as important material for oriental medication. Although several kinds of bioactive component of Potentilla chinensis extract from stems and leaves were identified, the major component of Potentilla chinensis from roots is not well established. In this study, the root of Potentilla chinensis was extracted in different solvent system and analyzed by high performance liquid chromatography (HPLC). According to HPLC analysis, a major component was isolated and its physicochemical properties were evaluated by mass spectrometry and nuclear magnetic resonance. Based on these results, isolated compound was identified as 2,3,8-Tri-O-methylellagic acid. And quantification of 2,3,8-Tri-O-methylellagic acid with different extraction solvent system was performed for industrial application.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.2
• /
• pp.590-596
• /
• 2010

Through this study, we have attempted the thermodynamic analysis on the dimethyl ether (DME) separation process, which can be used for diesel alternative fuel, additive to LPG and natural gas. And we also have completed the simulation of DME separation process using PRO/II with PROVISION. As an appropriate thermodynamic models, we selected NRTL liquid activity coefficient model to describe the non-ideality between methanol and water. To estimate the vapor phase non-idealities, we have chosen the Peng-Robinson equation of state model. And we also use the Henry's law option to predict the solubilities of non-condensible gases like CO, $CO_2$, $H_2$, $CH_2$ and $N_2$ in methanol solvent. Case study showed that optimal solvent to feed molar ratio was 3.40

• Journal of the Korean Magnetics Society
• /
• v.6 no.4
• /
• pp.251-257
• /
• 1996

A coercivity of barium ferrite (BaM) tape was found to be higher than the coercivity of BaM powder, This difference is in the range of 50 Oe to 600 Oe, which depends on substituted cations. physical properties of powder, and preparation conditions of the tape. The coercivity difference is attributed to both particle stacking and adsorption of organic solvent on particle surface. Regardless of substituted cations, the coercivity of longitudinally oriented BaFe tape was higher than that of BaM powder by a range of 100 Oe to 120 Oe, which is caused by particle stacking' During the active adsorption process on preparation of magnetic paint, where MEK (methyl ethyl ketone), TOL (toluene) and CHO (cyclohexanone) were used, chemisorption of solvents on the surface of substituted BaFe particle occurred to form polymeric compounds surrounding the particle. An increase in coercivity, caused by the solvent adsorption, was significant for Co-substutited BaM tape. Among these solvents CHO was the most effective one in increasing the coercivity of the Co-Ti substituted BaM tape.

• Journal of the Korean Chemical Society
• /
• v.41 no.8
• /
• pp.385-391
• /
• 1997

Diffusion Coefficient$(D_0)$ and electrode reaction rate Constant$(K_0)$ of Co$(dimethyl bipyridine)_3(ClO_4)_2$ were determined by cyclic voltammetry and chronoamperometry. It was also investigated that the effects of solvent, concentration, and scan rate, etc. on the diffusion coefficient and the temperature effect on the rate constant. The peak currents and diffusion coefficients were dcreased as increasing the viscosity of solvent. Diffusion coefficient was $5.54{\times}10^{-6 }cm^2/sec$ and the reaction rate constant was $2.39{\times}10^{-3 }/s$ at 25$^{\circ}C$. The thermodynamic parameters such as ${\Delta}G^{\neq},\;{\Delta}H^{\neq},\;and\;{\Delta}S$ were calculated from plotting the reaction rate constants versus the solution temperatures. This compound was shown the catalytic effect on the oxygen reduction that the reduction peak current of oxygen was greatly enhanced and the peak potential was shifted to +0.2 volt.

• Journal of the Korean Chemical Society
• /
• v.41 no.2
• /
• pp.63-68
• /
• 1997

Calorimetric measurements have been carried out for the binary mixture between protic, ROH (R=Me, Et) and dipolar aprotic solvents, MeCN,$Me_2CO,\;MeNO_2(or EtNO_2)$in order to investigate the molecular interaction and liquid structure of isodielectric solvents. From the measured partial molar enthalpies of the solutions, excess enthalpies for the mixing process were determined. The hydrogen bond strength between two components decreases in the order of$ROH-ROH>ROH-Me_2CO>ROH-MeCN>ROH-MeNO_2(or EtNO_2)$and the hydrogen bond donor acidity decreases in the order of MeOH>EtOH. From this result, we can conclude that the most important interaction for the formation of binary liquid mixture comes from the specific hydrogen bond.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.12
• /
• pp.2454-2458
• /
• 2007

Exploring the basic concepts for the design of CO2-philic molecules is important due to the possibility for “green” chemistry in supercritical CO2 as substitute solvent systems. The Lewis acid-base interactions and C?H…O weak hydrogen bonding were suggested as two key factors for the solubility of CO2-philic molecules. We have performed high level quantum mechanical calculations for the van der Waals complexes of CO2 with trimethylphosphate and trimethylphosphine oxide, which have long been used for metal extractants in supercritical CO2 fluid. Structures and energies were calculated using the MP2/6-31+G(d) and recently developed multilevel methods. These studies indicate that the Lewis acid-base interactions have larger impact on the stability of structure than the C?H…O weak hydrogen bonding. The weak hydrogen bonds in trimethylphosphine oxide have an important role to the large supercritical CO2 solubility when a metal is bound to the oxygen atom of the P=O group. Trimethylphosphate has many Lewis acid-base interaction sites so that it can be dissolved into supercritical CO2 easily even when it has metal ion on the oxygen atom of the P=O group, which is indispensable for a good extractant.

• Journal of Powder Materials
• /
• v.6 no.1
• /
• pp.88-95
• /
• 1999

The purpose of this study is to investigate the manufacturing feasibility of WC-Co milling inserts via Powder Injection Molding (PIM) process. WC-Co is used in a wide variety of cutting tools due to its high hardness, stiffness, compressive strength and wear resistance properties. WC-Co parts for a high stress application were conventionally produced by the press and sinter method, which were Iimited to 2 dimensional shapes. Manufacturing WC-Co parts for a high stress application by PIM implies that tool efficiency can be highly improved due to increased freedom is design. P30 grade WC powder (WC-Co-TiC-TaC system) was mixed with RIST-5B133 binder and injection molded into milling inserts (Taegu Tech. Model WCMX 06T 308). The mean grain size of the powder was about 0.8$\mu$m. Injection molded specimens were debound by solvent extraction and thermal degradation method at various conditions. The specimens were sintered at 140$0^{\circ}C$ for 1 hr in vacuum. Carbon content, weight loss, dimensional change, and macro defects of the specimen were carefully monitored at each stage of the PIM process. PIMed WC-Co milling inserts reached 100% full density after sinteing. Its mechanical properties and micro-structures were comparable with the press and sintered milling insert. Carbon content of the sintered WC-Co insert was mainly determained by the atmosphere of thermal debinding. By controlling powder loading and injection molding condition, dimensional accuracy could be obtained within 0.4%. We confirm that PIM can not only be an alternative manufacturing method for WC-Co parts economically but also provide a design freedom for more effieient cutting tools.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.30 no.1
• /
• pp.1-19
• /
• 2012

According as gradually increasing the demand for eco-friendly at the printing process, it has been progressed fairly development. Especially, the inks are used by soy oil beginning of ink industry for preventing environment, it is possible to make eco-friendly inks with vegetable ester. So it is not necessary to use petroleum-based solvents at all for preventing environment. These eco-friendly inks have a benefits they are able to use the renewable resource. But basically vegetable oils have that reduce the VOC(Volatile Organic Compound) and high viscosity, high solubility properties. So if the vegetable oils use in the ink, set off problem occur on the paper because of slow drying time. In case of vegetable ester, it has similar the molecular weight and kinetic viscosity with hydrocarbon solvent, it is able to control the power of dilution about the resin. So, it has benefit that solve the problem of the existing eco-friendly inks. In this study, different types of ester were made by six types of vegetable oils and used ester in the varnishes and inks properties are comparison with hydrocarbon solvent based ink. By considering the intrinsic properties of vegetable oil, ester used to analyze the changes in ink properties, using ester varnish is applied to study the rheology characteristics and emulsification with inks.